ROOF HEADLINING REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

PROCEDURE


  1. INSTALL TONNEAU COVER STOPPER

    Tech Tips

    Use the same procedure for both tonneau cover stoppers.


    1. B0029MW

      Install the tonneau cover stopper with the 2 screws.

  2. INSTALL TONNEAU COVER STOPPER SILENCER (w/ Silencer)

    Tech Tips

    Use the same procedure for both tonneau cover stopper silencers.


    1. B0029GO

      Install a new tonneau cover stopper silencer in the location shown in the illustration using double-sided tape.

  3. INSTALL NO. 2 ANTENNA CORD SUB-ASSEMBLY

    Click here

  4. INSTALL NO. 1 ROOF WIRE


    1. w/o Sliding Roof:


      1. Apply new double-sided tape as shown in the illustration.

        B0029XZC01
        *a 1 mm (0.0394 in.) *b 15 mm (0.590 in.)
        B002AN0 Double-sided Tape - -

      2. Attach the No. 1 roof wire to the double-sided tape.

      3. Apply new one-sided tape.

      4. Turn the 2 connectors approximately 90° counter clockwise to connect them.

      5. If any slack forms, take up the slack in the areas A shown in the illustration.

        Note

        Secure any wire that protrudes from the double-sided tape with one-sided tape.

      6. Check that the No. 1 roof wire is not twisted, raised, or protruding in any way.

        B002AJUC01
        *A w/ EC Mirror, w/o Pre-crash Safety System *B w/ EC Mirror, w/ Pre-crash Safety System
        *C w/ Rain Sensor, w/o Pre-crash Safety System *D w/ Rain Sensor, w/ Pre-crash Safety System
        *E w/ Pre-crash Safety System *F w/ Camera Heater
        *1 No. 1 Roof Wire - -
        *a 90° - -
        B002AN0 One-sided Tape B002A77 Double-sided Tape

    2. w/ Sliding Roof:


      1. Apply new double-sided tape as shown in the illustration.

        B002AAOC01
        *a 1 mm (0.0394 in.) *b 15 mm (0.590 in.)
        B002AN0 Double-sided Tape - -

      2. Attach the No. 1 roof wire to the double-sided tape.

      3. Apply new one-sided tape.

      4. Turn the 2 connectors approximately 90° counter clockwise to connect them.

      5. If any slack forms, take up the slack in the areas A shown in the illustration.

        Note

        Secure any wire that protrudes from the double-sided tape with one-sided tape.

      6. Check that the No. 1 roof wire is not twisted, raised, or protruding in any way.

        B0029SKC01
        *A w/ EC Mirror, w/o Pre-crash Safety System *B w/ EC Mirror, w/ Pre-crash Safety System
        *C w/ Rain Sensor, w/o Pre-crash Safety System *D w/ Rain Sensor, w/ Pre-crash Safety System
        *E w/ Pre-crash Safety System *F w/ Camera Heater
        *1 No. 1 Roof Wire - -
        *a 90° - -
        B002AN0 One-sided Tape B002A77 Double-sided Tape

  5. INSTALL VANITY LIGHT ASSEMBLY LH


    1. Attach the claw to install the vanity light assembly LH.

    2. Attach the 2 claws to connect the bulb holder to the vanity light assembly LH.

  6. INSTALL VANITY LIGHT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. INSTALL NO. 2 ROOF HEADLINING PAD (for Cold Area)


    1. B002AI7C01
      B002AN0 Silencer Marking

      Install a new No. 2 roof headlining pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.

  8. INSTALL ROOF HEADLINING PAD (for Cold Area)

    Tech Tips

    Use the same procedure for both roof headlining pads.


    1. B0029S0C01
      B002AN0 Silencer Marking

      Install a new roof headlining pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.

  9. INSTALL NO. 3 ROOF SILENCER PAD


    1. B002A9LC01
      B002AN0 Silencer Marking

      Install a new No. 3 roof silencer pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.

  10. INSTALL NO. 1 ROOF SILENCER PAD (w/o Sliding Roof)


    1. Install a new No. 1 roof silencer pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.

      B0029N3C01
      B002AN0 Silencer Marking - -

  11. INSTALL NO. 1 ROOF SILENCER PAD (w/ Sliding Roof)


    1. B0029UTC01
      B002AN0 Silencer Marking

      Install a new No. 2 roof silencer pad using double-sided tape, hot-melt glue or adhesive as shown in the illustration.

  12. INSTALL CENTER ROOF HEADLINING PAD


    1. Install a new center roof headlining pads using double-sided tape, hot-melt glue or adhesive as shown in the illustration.

      B002APJC01
      *A for RH Side *B for LH Side, Type A
      *C for LH Side, Type B - -
      *a Silencer Marking - -