UPPER INSTRUMENT PANEL INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for RHD and LHD vehicles.

  • The procedure listed below is for LHD vehicles.

  • A bolt without a torque specification is shown in the standard bolt chart.

    Click here

PROCEDURE


  1. INSTALL UPPER INSTRUMENT PANEL


    1. Attach the 8 clips to install the upper instrument panel.

    2. for Single Type Airbag:


      1. Install the 2 bolts <C> or <D>.

      2. Install the 2 bolts <B>.

        Torque:
        20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      3. Connect each connector.

        A01KC5AC01
        *1 Bolt <B> *2 Bolt <C> or <D>
        *3 Airbag Connector - -
      4. A01KBT6C01
        *1 Lock Slider
        *a Lock Position

        Connect the airbag connector.

        Note

        When handling the airbag connector, take care not to damage the airbag wire harness.

      5. Check that the lock slider is in the lock position.

    3. for Dual Type Airbag:


      1. Install the 2 bolts <C> or <D>.

      2. Install the 2 bolts <B>.

        Torque:
        20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      3. Connect each connector.

        A01KB17C01
        *1 Bolt <B> *2 Bolt <C> or <D>
        *3 Airbag Connector A *4 Airbag Connector B
      4. A01KBK9C01
        *1 Airbag Connector A
        *2 Airbag Connector B
        *3 Lock Slider
        *a Lock Position

        Connect the 2 airbag connectors A and B.

        Note

        When handling the airbag connector, take care not to damage the airbag wire harness.

      5. Check that the lock slider is in the lock position.

  2. INSTALL FRONT PILLAR GARNISH LH (w/o Curtain Shield Airbag)

    Click here

  3. INSTALL FRONT PILLAR GARNISH RH (w/o Curtain Shield Airbag)

    Click here

  4. INSTALL FRONT PILLAR GARNISH LH (w/ Curtain Shield Airbag)

    Click here

  5. INSTALL FRONT PILLAR GARNISH RH (w/ Curtain Shield Airbag)

    Click here

  6. INSTALL FRONT NO. 2 SPEAKER ASSEMBLY

    Click here

  7. INSTALL NO. 2 SPEAKER HOLE COVER (w/o Speaker)


    1. A01KD0Q

      Attach the 2 guides, 2 clips and 2 claws to install the No. 2 speaker hole cover.

  8. INSTALL NO. 1 SPEAKER HOLE COVER (w/o Speaker)

    Tech Tips

    Use the same procedure described for the No. 2 speaker hole cover.

  9. INSTALL NO. 2 SPEAKER HOLE COVER (w/ Speaker)

    Click here

  10. INSTALL NO. 1 SPEAKER HOLE COVER (w/ Speaker)

    Tech Tips

    Use the same procedure described for the No. 2 speaker hole cover.

  11. INSTALL GLOVE COMPARTMENT DOOR ASSEMBLY


    1. A01KATEC01
      A01KCE6 Protective Tape

      Apply protective tape as shown in the illustration.

    2. Attach the 2 hinges to install the glove compartment door assembly.

    3. A01KBEFC01
      A01KCE6 Protective Tape

      While pushing in the sides of the glove compartment door assembly, attach the 2 stoppers.

    4. Connect the glove compartment door stopper sub-assembly.

  12. INSTALL UPPER INSTRUMENT CLUSTER FINISH PANEL


    1. Attach the 4 clips to install the upper instrument cluster finish panel.

  13. INSTALL NO. 2 INSTRUMENT PANEL GARNISH SUB-ASSEMBLY


    1. for LHD with Entry and Start System:

      Connect the connector.

    2. Attach the 13 clips to install the No. 2 instrument panel garnish sub-assembly.

      A01KBG8

  14. INSTALL AIR CONDITIONING CONTROL ASSEMBLY (for Automatic Air Conditioning System)

    Click here

  15. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY (except Automatic Air Conditioning System)


    1. Connect each connector.

    2. A01KBI9

      Attach the 2 clips to install the lower center instrument cluster finish panel sub-assembly.

  16. INSTALL HEADLIGHT DIMMER SWITCH

    Click here

  17. INSTALL COMBINATION METER ASSEMBLY

    Click here

  18. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL


    1. A01KDRD

      Attach the 11 clips and claw to install the No. 1 instrument cluster finish panel.

  19. INSTALL STEREO OPENING COVER (w/o Audio)


    1. A01KDE3

      Attach the 4 clips to install the stereo opening cover.

    2. Install the 4 bolts.

  20. INSTALL RADIO RECEIVER ASSEMBLY (w/ Radio Receiver)

    Click here

  21. INSTALL NAVIGATION RECEIVER (w/ Navigation System)

    Click here

  22. INSTALL TELLTALE LIGHT ASSEMBLY

    Click here

  23. INSTALL NO. 3 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01KCB0

      Attach the 2 clips and 2 claws to install the No. 3 instrument panel register assembly.

  24. INSTALL NO. 4 INSTRUMENT PANEL REGISTER ASSEMBLY


    1. A01KAKX

      Attach the 3 clips and claw to install the No. 4 instrument panel register assembly.

  25. INSTALL CENTER NO. 1 INSTRUMENT CLUSTER FINISH PANEL


    1. Attach the 6 clips and 2 claws to install the center No. 1 instrument cluster finish panel.

      A01KDE0

  26. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  27. CHECK SRS WARNING LIGHT

    Click here