OUTER MIRROR SWITCH INSPECTION

PROCEDURE

1. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/o Retract Mirror)

   
   

   1. Check the mirror select switch and mirror surface adjust switch.

      
      
      1. 

         *1	Mirror Select Switch
         *2	Mirror Surface Adjust Switch
         *a	Component without harness connected (Outer Mirror Switch Assembly)

         Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for left side)
         Tester Connection Condition Specified Condition 16 (VL) - 22 (B) 19 (M+) - 20 (E) UP Below 1 Ω OFF 10 kΩ or higher 16 (VL) - 20 (E) 19 (M+) - 22 (B) DOWN Below 1 Ω OFF 10 kΩ or higher 17 (HL) - 22 (B) 19 (M+) - 20 (E) LEFT Below 1 Ω OFF 10 kΩ or higher 17 (HL) - 20 (E) 19 (M+) - 22 (B) RIGHT Below 1 Ω OFF 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for right side)
         Tester Connection Condition Specified Condition 15 (VR) - 22 (B) 19 (M+) - 20 (E) UP Below 1 Ω OFF 10 kΩ or higher 15 (VR) - 20 (E) 19 (M+) - 22 (B) DOWN Below 1 Ω OFF 10 kΩ or higher 14 (HR) - 22 (B) 19 (M+) - 20 (E) LEFT Below 1 Ω OFF 10 kΩ or higher 14 (HR) - 20 (E) 19 (M+) - 22 (B) RIGHT Below 1 Ω OFF 10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.

2. INSPECT OUTER MIRROR SWITCH ASSEMBLY (w/ Retract Mirror)

   
   

   1. Check the mirror select switch and mirror surface adjust switch.

      
      
      1. 

         *1	Mirror Select Switch
         *2	Mirror Surface Adjust Switch
         *3	Retract Switch
         *a	Component without harness connected (Outer Mirror Switch Assembly)

         Turn the mirror select switch to the L position.

      2. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for left side)
         Tester Connection Condition Specified Condition 16 (VL) - 22 (B) 19 (M+) - 20 (E) UP Below 1 Ω OFF 10 kΩ or higher 16 (VL) - 20 (E) 19 (M+) - 22 (B) DOWN Below 1 Ω OFF 10 kΩ or higher 17 (HL) - 22 (B) 19 (M+) - 20 (E) LEFT Below 1 Ω OFF 10 kΩ or higher 17 (HL) - 20 (E) 19 (M+) - 22 (B) RIGHT Below 1 Ω OFF 10 kΩ or higher

      3. Turn the mirror select switch to the R position.

      4. Measure the resistance according to the value(s) in the table below.

         Standard Resistance (for right side)
         Tester Connection Condition Specified Condition 15 (VR) - 22 (B) 19 (M+) - 20 (E) UP Below 1 Ω OFF 10 kΩ or higher 15 (VR) - 20 (E) 19 (M+) - 22 (B) DOWN Below 1 Ω OFF 10 kΩ or higher 14 (HR) - 22 (B) 19 (M+) - 20 (E) LEFT Below 1 Ω OFF 10 kΩ or higher 14 (HR) - 20 (E) 19 (M+) - 22 (B) RIGHT Below 1 Ω OFF 10 kΩ or higher

         If the result is not as specified, replace the outer mirror switch assembly.

   2. Check the retract switch.

      
      

      1. Measure the resistance according to the value(s) in the table below.

         Standard Resistance
         If the result is not as specified, replace the outer mirror switch assembly. Tester Connection Condition Specified Condition 24 (MF) - 20 (E) 23 (MR) - 22 (B) Pushed in Below 1 Ω 24 (MF) - 22 (B) 23 (MR) - 20 (E) Not pushed in Below 1 Ω

         If the result is not as specified, replace the outer mirror switch assembly.