DATA LIST
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Back Door, Main Body or Entry&Start* / Data List.
*: w/ Entry and Start System
According to the display on the GTS, read the Data List.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Door Lock Status | Back door condition signal | Lock or Unlock | Lock: Back door locked Unlock: Back door unlocked |
- |
| Half Latch SW | Latch switch signal | ON or OFF | ON: Back door lock motor open-latched OFF: Back door lock motor full-latched or half-latched |
- |
| Closer Position SW | Sector switch signal | ON or OFF | ON: Back door lock sector gear in center position OFF: Back door lock sector gear out of center position |
- |
| Pawl Position Switch | Pawl switch signal | ON or OFF | ON: Back door lock motor open-latched OFF: Back door lock motor except open-latched |
Refer to "POWER BACK DOOR OPERATION TIMING CHART"*1 |
| Courtesy SW | Back door courtesy switch signal | ON or OFF | ON: Back door open OFF: Back door closed |
- |
| PBD Touch Sensor (Right) | Power back door sensor assembly RH signal | ON, OFF or Open | ON: Power back door sensor assembly RH pressed OFF: Power back door sensor assembly RH not pressed Open: Power back door sensor assembly RH circuit open |
- |
| PBD Touch Sensor (Left) | Power back door sensor assembly LH signal | ON, OFF or Open | ON: Power back door sensor assembly LH pressed OFF: Power back door sensor assembly LH not pressed Open: Power back door sensor assembly LH circuit open |
- |
| PBD Main SW | Power back door main switch signal | ON or OFF | ON: Power back door main switch pushed OFF: Power back door main switch not pushed |
- |
| PBD Close SW | Door control switch assembly signal | ON or OFF | ON: Door control switch assembly pushed OFF: Door control switch assembly not pushed |
- |
| IG SW | Ignition switch signal | ON or OFF | ON: Ignition switch ON OFF: Ignition switch off |
"OFF" is also displayed for this item when the ignition switch is ACC. |
| PBD Position (3/4-Open) | Load signal detected during back door closing operation (3/4 - Open) | Caution or OK | Caution: Load detected between back door 3/4 and fully open position during back door closing operation OK: No load detected between back door 3/4 and fully open position during back door closing operation |
- |
| PBD Position (2/4-3/4) | Load signal detected during back door closing operation (2/4 - 3/4) | Caution or OK | Caution: Load detected between back door 2/4 and 3/4 open position during back door closing operation OK: No load detected between back door 2/4 and 3/4 open position during back door closing operation |
- |
| PBD Position (1/4-2/4) | Load signal detected during back door closing operation (1/4 - 2/4) | Caution or OK | Caution: Load detected between back door 1/4 and 2/4 open position during back door closing operation OK: No load detected between back door 1/4 and 2/4 open position during back door closing operation |
- |
| PBD Position (Close-1/4) | Load signal detected during back door closing operation (Close - 1/4) | Caution or OK | Caution: Load detected between back door fully closed and 1/4 open position during back door closing operation OK: No load detected between back door fully closed and 1/4 open position during back door closing operation |
- |
| Closed Position Initialization | Back door fully closed position memorized signal | Not Initialized or Initialized | Not Initialized: Back door fully closed position not memorized Initialized: Back door fully closed position memorized |
- |
| PBD SW Operation | Power back door switch operation | ON or 0.8s | Current customize setting displayed | - |
| PBD Assist Open Operation | Power back door warning buzzer operation condition signal | ON or OFF | Current customize setting displayed | - |
| PBD Assist Close Operation | Function that enables or disables the power back door assist open operation. When PBD Assist Open is set to on (enabled) the back door will open automatically when the back door opener switch assembly (opener switch) is operated. | OFF or ON | Current customize setting displayed | - |
| Door Unlock with 1 Motion. | Function that selects the door or doors to unlock when the back door is locked and the transmitter switch is pushed to operate the power back door. | Back Door or ALL DOORS | Current customize setting displayed | - |
| Wireless Power Back Door Open | Function that operates the power back door by pushing the transmitter switch (electrical key transmitter sub-assembly). | Lock:OFF/Unlock:OFF, Lock:OFF/Unlock:ON, Lock:OFF/Unlock:Twice, Lock:OFF/Unlock:0.8s, Lock:Twice/Unlock:Twice or Lock:0.8s/Unlock:0.8 | Current customize setting displayed | Opening operation differs depending on the country. |
| Power Back Door Opening Adjust | Function that can be used to set the power back door opening angle at 6 different positions. | Min, Small, Middle, Large, Max or User Setting Position | Current customize setting displayed | - |
| Emblem Sensor | Whether rear emblem sensor assembly is equipped or not*2 | Without or With | Without: Rear emblem sensor assembly not equipped With: Rear emblem sensor assembly equipped |
Not applicable |
| Emblem Sensor Detection | Rear emblem sensor assembly detection status*2 | ON or OFF | ON: Rear emblem sensor assembly detecting OFF: Rear emblem sensor assembly not detecting |
Not applicable |
| PBD/Emblem Sensor Function | PBD and rear emblem sensor assembly function setting status*2 | PBD OFF/Emblem OFF, PBD ON/Emblem OFF or PBD ON/Emblem ON | Customized value displayed | Not applicable |
| PBD Buzzer Volume Adjust | PBD buzzer volume setting status | Small, Middle or Large | Customized value displayed | - |
| PBD Buzzer Function | PBD buzzer sounding function setting status | OFF, Start Buzzer On/In Operation Buzzer OFF, Start Buzzer OFF/In Operation Buzzer ON or ON | Customized value displayed | - |
| PBD Buzzer Tone | PBD buzzer tone setting status | Pattern A, Pattern B or Pattern C | Customized value displayed | - |
| Emblem Sensor Detection Sensitivity | Rear emblem sensor assembly detection sensitivity setting status*2 | Low, Middle or High | Customized value displayed | Not applicable |
| Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Frequent Contact/Calibration Failure) | Number of emblem sensor sensitivity reduction mode transitions (frequent contact or calibration failure)*2 | None, Low, Middle or HIgh | None: 0 sensitivity reductions Low: 1 to 10 sensitivity reductions Middle: 1 to 10 sensitivity reductions High: 51 or more sensitivity reductions |
Not applicable |
| Emblem Sensor Sensitivity Reduction Mode Transition Frequency (Power Saving) | Number of emblem sensor sensitivity reduction mode transitions (frequent contact or calibration failure)*2 | None, Low, Middle or HIgh | None: 0 sensitivity reductions Low: 1 to 10 sensitivity reductions Middle: 11 to 50 sensitivity reductions High: 51 or more sensitivity reductions |
Not applicable |
| Emblem Sensor Sensitivity Drop Frequency (Disturbance Factor) | Number of emblem sensor sensitivity reduction mode transitions (power saving)*2 | None, Low, Middle or HIgh | None: 0 sensitivity reductions Low: 1 to 10 sensitivity reductions Middle: 11 to 50 sensitivity reductions High: 51 or more sensitivity reductions |
Not applicable |
| Emblem Sensor Sensitivity Drop Frequency (Foreign Matter Adhering) | Number of emblem sensor sensitivity reduction mode transitions (disturbance factor)*2 | None, Low, Middle or HIgh | None: 0 sensitivity reductions Low: 1 to 10 sensitivity reductions Middle: 11 to 50 sensitivity reductions High: 51 or more sensitivity reductions |
Not applicable |
| #Codes | The number of DTCs | Min.: 0 Max.: 255 |
The number of DTCs | - |
*1: Refer to "POWER BACK DOOR OPERATION TIMING CHART"
*2: Although the item is displayed on the GTS, it is not applicable to this vehicle.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Back Door Open | Back door lock | Permit or Prohibit | Permit: Back door unlocked Prohibit: Back door locked |
- |
| Back Door Open SW | Back door control switch signal | ON or OFF | ON: Back door control switch on OFF: Back door control switch off |
- |
| Back Door Open Handle SW | Back door opener switch assembly signal | ON or OFF | ON: Back door opener switch assembly on OFF: Back door opener switch assembly off |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Tr/B-Door Unlock SW | Back door opener switch assembly signal | ON or OFF | ON: Back door opener switch assembly on OFF: Back door opener switch assembly off |
- |
ACTIVE TEST
Tech Tips
Using the GTS to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Body Electrical / Back Door / Active Test.
According to the display on GTS perform the "Active Test".
| Tester Display | Measurement Item | Control Range | Diagnostic Note |
|---|---|---|---|
| Latch Release | Latch release operation | ON or OFF | - |
| PBD Open/Close | Power back door motor operation | Forward, Reverse or OFF | - |
| PBD Buzzer | Power back door warning buzzer sound | ON or OFF | - |