AIRBAG SYSTEM(w/o Occupant Classification System), Diagnostic DTC:B1830/57, B1831/57, B1832/57, B1833/57

DTC Code DTC Name
B1830/57 Short in Curtain Shield Squib RH Circuit
B1831/57 Open in Curtain Shield Squib RH Circuit
B1832/57 Short to GND in Curtain Shield Squib RH Circuit
B1833/57 Short to B+ in Curtain Shield Squib RH Circuit

DESCRIPTION

The curtain shield squib RH circuit consists of the airbag sensor assembly and curtain shield airbag assembly RH.

The circuit instructs the SRS to deploy when deployment conditions are met.

These DTCs are stored when a malfunction is detected in the curtain shield squib RH circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1830/57 Short in Curtain Shield Squib RH Circuit

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal 5 times in the curtain shield squib RH circuit during the primary check.

  • A curtain shield squib RH malfunction.

  • A airbag sensor assembly malfunction.

  • Floor wire

  • Curtain shield airbag assembly RH (Curtain shield squib RH)

  • Airbag sensor assembly
B1831/57 Open in Curtain Shield Squib RH Circuit

One of the following conditions is met:


  • The airbag sensor assembly detects an open circuit signal in the curtain shield squib RH circuit for 2 seconds.

  • A curtain shield squib RH malfunction.

  • A airbag sensor assembly malfunction.

  • Floor wire

  • Curtain shield airbag assembly RH (Curtain shield squib RH)

  • Airbag sensor assembly
B1832/57 Short to GND in Curtain Shield Squib RH Circuit

One of the following conditions is met:


  • The airbag sensor assembly detects a short circuit to ground signal in the curtain shield squib RH circuit for 0.5 seconds.

  • A curtain shield squib RH malfunction.

  • A airbag sensor assembly malfunction.

  • Floor wire

  • Curtain shield airbag assembly RH (Curtain shield squib RH)

  • Airbag sensor assembly
B1833/57 Short to B+ in Curtain Shield Squib RH Circuit

One of the following conditions is met:


  • The airbag sensor assembly detects a short circuit to B+ signal in the curtain shield squib RH circuit for 0.5 seconds.

  • A curtain shield squib RH malfunction.

  • A airbag sensor assembly malfunction.

  • Floor wire

  • Curtain shield airbag assembly RH (Curtain shield squib RH)

  • Airbag sensor assembly

WIRING DIAGRAM

A01VA3OE45
*a Curtain Shield Airbag Assembly RH (Curtain Shield Squib RH)
*b Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

  • After replacing the airbag sensor assembly, refer to initialization.

    Click here

Tech Tips

To perform the simulation method, enter check mode (signal check) with the GTS (Click here ), and then wiggle each connector of the airbag system or drive the vehicle on various types of road Click here.

PROCEDURE


  1. CHECK CURTAIN SHIELD AIRBAG ASSEMBLY RH (CURTAIN SHIELD SQUIB RH)


    1. A01VAHLC01
      *1 Curtain Shield Squib RH
      *2 Airbag Sensor Assembly
      *3 Connector C
      *a

      Front view of wire harness connector

      (to Curtain Shield Squib RH)

      Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Disconnect the connector from the curtain shield airbag assembly RH.

    4. Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.

      CAUTION:

      Never connect the tester to the curtain shield airbag assembly RH (curtain shield squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

      Note


      • Do not forcibly insert SST into the terminals of the connector when connecting SST.

      • Insert SST straight into the terminals of the connector.

      SST
      09843-18061

    5. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    8. Turn the ignition switch off.

    9. Turn the ignition switch to ON, and wait for at least 60 seconds.

    10. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTC B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.

    11. Turn the ignition switch off.

    12. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    13. Disconnect SST from connector C.

      Result
      Proceed to
      DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output
      DTC B1830/57, B1831/57, B1832/57 or B1833/57 is output

    DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output

    REPLACE CURTAIN SHIELD AIRBAG ASSEMBLY RH Click here

    DTC B1830/57, B1831/57, B1832/57 or B1833/57 is output

  2. CHECK CONNECTOR


    1. Disconnect the connectors from the airbag sensor assembly.

    2. A01V70VC04
      *1 Curtain Shield Squib RH
      *2 Floor Wire
      *3 Airbag Sensor Assembly

      Check that the connectors (on the airbag sensor assembly side and curtain shield airbag assembly RH side) are not damaged.

      OK
      The lock button is not disengaged, and the claw of the lock is not deformed or damaged.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  3. CHECK CURTAIN SHIELD SQUIB RH CIRCUIT


    1. A01V862C02
      *1 Curtain Shield Squib RH
      *2 Floor Wire
      *3 Airbag Sensor Assembly
      *4 Connector C
      *a

      Front view of wire harness connector

      (to Curtain Shield Squib RH)

      Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      M9-1 (ICR+) - Body ground Ignition switch ON Below 1 V
      M9-2 (ICR-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M9-1 (ICR+) - M9-2 (ICR-) Always Below 1 Ω

    7. Release the activation prevention mechanism built into connector B.

      Click here

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M9-1 (ICR+) - M9-2 (ICR-) Always 1 MΩ or higher

    9. Restore the released activation prevention mechanism of connector B to its original condition.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M9-1 (ICR+) - Body ground Always 1 MΩ or higher
      M9-2 (ICR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE FLOOR WIRE

    OK

  4. CHECK AIR BAG SENSOR ASSEMBLY


    1. A01V9XEC01
      *1 Curtain Shield Squib RH
      *2 Airbag Sensor Assembly

      Connect the connectors to the curtain shield airbag assembly RH and airbag sensor assembly.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes

      Tech Tips

      Codes other than DTC B1830/57, B1831/57, B1832/57 and B1833/57 may be output at this time, but they are not related to this check.

      Result
      Proceed to
      DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output
      DTC B1830/57, B1831/57, B1832/57 or B1833/57 is output

    DTC B1830/57, B1831/57, B1832/57 or B1833/57 is not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC B1830/57, B1831/57, B1832/57 or B1833/57 is output

    REPLACE AIR BAG SENSOR ASSEMBLY Click here