AIRBAG SYSTEM(w/o Occupant Classification System), Diagnostic DTC:B1642/81, B1647/82

DTC Code DTC Name
B1642/81 Lost Communication with Side Satellite Sensor Bus RH
B1647/82 Lost Communication with Side Satellite Sensor Bus LH

DESCRIPTION

The circuit for the side collision sensor LH or RH (to determine deployment of the front seat airbag assembly LH or RH and curtain shield airbag assembly LH or RH) is composed of the airbag sensor assembly, rear airbag sensor LH or RH and door side airbag sensor LH or RH.

The door side airbag sensor LH or RH and rear airbag sensor LH or RH detect impacts to the vehicle and send signals to the airbag sensor assembly to determine if the airbag should be deployed.

DTC B1642/82 or B1647/82 is stored when a malfunction is detected in the circuit for the side satellite sensor bus LH or RH (to determine deployment of the front seat airbag assembly LH or RH and curtain shield airbag assembly LH or RH).

DTC No. Detection Item DTC Detection Condition Trouble Area
B1642/81 Lost Communication with Side Satellite Sensor Bus RH

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus RH for 2 seconds.

  • A door side airbag sensor RH malfunction.

  • A rear airbag sensor RH malfunction.

  • A airbag sensor assembly malfunction.

  • Floor wire

  • Door side airbag sensor RH

  • Rear airbag sensor RH

  • Airbag sensor assembly
B1647/82 Lost Communication with Side Satellite Sensor Bus LH

One of the following conditions is met:


  • The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the circuit for the side satellite sensor bus LH for 2 seconds.

  • A door side airbag sensor LH malfunction.

  • A rear airbag sensor LH malfunction.

  • A airbag sensor assembly malfunction.

  • No. 2 floor wire

  • Door side airbag sensor LH

  • Rear airbag sensor LH

  • Airbag sensor assembly

WIRING DIAGRAM

A01V8TXE01
for RH Side
*a Airbag Sensor Assembly
*b Rear Airbag Sensor RH
*c Door Side Airbag Sensor RH
A01V8TXE02
for LH Side
*a Airbag Sensor Assembly
*b Rear Airbag Sensor LH
*c Door Side Airbag Sensor LH

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

  • After replacing the airbag sensor assembly, refer to initialization.

    Click here

PROCEDURE


  1. CHECK DTC


    1. Turn the ignition switch to off.

    2. Turn the ignition switch to ON, and wait for at least 60 seconds.

    3. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1642/81 is output
      DTC B1647/82 is output
      DTC B1642/81 and B1647/82 are not output

      Tech Tips

      Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.


    DTC B1647/82 is output

    CHECK CONNECTION OF CONNECTORS Click here

    DTC B1642/81 and B1647/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC B1642/81 is output

  2. CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the airbag sensor assembly and rear airbag sensor RH.

      Result
      Proceed to
      The connectors are properly connected
      The connectors are not properly connected

    The connectors are not properly connected

    CONNECT CONNECTORS PROPERLY

    The connectors are properly connected

  3. CHECK CONNECTORS


    1. Disconnect the connectors from the airbag sensor assembly and rear airbag sensor RH.

    2. A01V6UOC01
      *1 Rear Airbag Sensor RH
      *2 Airbag Sensor Assembly
      *3 Floor Wire

      Check that the connectors (on the airbag sensor assembly side and rear airbag sensor RH side) are not damaged.

      Result
      Proceed to
      The connectors are not deformed or damaged
      The connectors are deformed or damaged

    The connectors are deformed or damaged

    REPLACE FLOOR WIRE

    The connectors are not deformed or damaged

  4. CHECK REAR AIRBAG SENSOR RH CIRCUIT


    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      A01V6XUC01
      *1 Rear Airbag Sensor RH *2 Airbag Sensor Assembly
      *3 Floor Wire *4 Connector C
      *5 Connector B *6 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      M7-4 (BCR+) - Body ground Ignition switch ON Below 1 V
      M7-3 (BCR-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 8 (BBR+) and 15 (BBR-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M7-4 (BCR+) - M7-3 (BCR-) Always Below 1 Ω

    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M7-4 (BCR+) - M7-3 (BCR-) Always 1 MΩ or higher
      M7-4 (BCR+) - Body ground Always 1 MΩ or higher
      M7-3 (BCR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    GO TO STEP 9 Click here

    OK

  5. CHECK CONNECTION OF CONNECTOR


    1. Check that the connector is properly connected to the door side airbag sensor RH.

      Result
      Proceed to
      The connector is properly connected
      The connector is not properly connected

    The connector is not properly connected

    CONNECT CONNECTOR PROPERLY

    The connector is properly connected

  6. CHECK CONNECTOR


    1. Disconnect the connector from the door side airbag sensor RH.

    2. A01V9O9C05
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor RH

      Check that the connector (on the door side airbag sensor RH side) is not damaged.

      Result
      Proceed to
      The connector is not deformed or damaged
      The connector is deformed or damaged

    The connector is deformed or damaged

    REPLACE HARNESS AND CONNECTOR

    The connector is not deformed or damaged

  7. CHECK DOOR SIDE AIRBAG SENSOR RH CIRCUIT


    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      A01V9DRC01
      *1 Door Side Airbag Sensor RH *2 Rear Airbag Sensor RH
      *3 Connector E *4 Connector B
      *5 Service Wire - -
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor RH)

      		 *b

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      M7-1 (BDR+) - Body ground Ignition switch ON Below 1 V
      M7-2 (BDR-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector E.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M7-1 (BDR+) - M7-2 (BDR-) Always Below 1 Ω

    8. Disconnect the service wire from connector E.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M7-1 (BDR+) - M7-2 (BDR-) Always 1 MΩ or higher
      M7-1 (BDR+) - Body ground Always 1 MΩ or higher
      M7-2 (BDR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FLOOR WIRE Click here

    OK

  8. CHECK REAR AIRBAG SENSOR RH


    1. A01VA30C01
      *1 Rear Airbag Sensor LH
      *2 Airbag Sensor Assembly

      Connect the connectors to the airbag sensor assembly and door side airbag sensor RH.

    2. Interchange the rear airbag sensor RH with LH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 90 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1647/82 is output
      DTC B1642/81 is output
      DTC B1642/81 and B1647/82 are not output

      Tech Tips

      Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the rear airbag sensor LH and RH to their original positions and connect the connectors to them.


    DTC B1647/82 is output

    REPLACE REAR AIRBAG SENSOR RH Click here

    DTC B1642/81 is output

    CHECK DOOR SIDE AIRBAG SENSOR RH Click here

    DTC B1642/81 and B1647/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

  9. CHECK FLOOR WIRE


    1. Disconnect the floor wire connector from the front door wire RH.

      A01V6W7C02
      *1 Door Side Airbag Sensor RH *2 Rear Airbag Sensor RH
      *3 Front Door Wire RH *4 Floor Wire
      *5 Connector C *6 Connector B
      *7 Service Wire - -
      *a

      Front view of wire harness connector

      (to Front Door Wire RH)

      		 *b

      Front view of wire harness connector

      (to Rear Airbag Sensor RH)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      M7-1 (BDR+) - Body ground Ignition switch ON Below 1 V
      M7-2 (BDR-) - Body ground Ignition switch ON Below 1 V

    5. Turn the ignition switch off.

    6. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    7. Using a service wire, connect terminals 2 (BDR+) and 1 (BDR-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M7-1 (BDR+) - M7-2 (BDR-) Always Below 1 Ω

    9. Disconnect the service wire from connector C.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M7-1 (BDR+) - M7-2 (BDR-) Always 1 MΩ or higher
      M7-1 (BDR+) - Body ground Always 1 MΩ or higher
      M7-2 (BDR-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE RH Click here

    NG

    REPLACE FLOOR WIRE

  10. CHECK DOOR SIDE AIRBAG SENSOR RH


    1. A01V700C15
      *1 Door Side Airbag Sensor LH
      *2 Rear Airbag Sensor RH

      Interchange the door side airbag sensor RH with LH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 90 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1647/82 is output
      DTC B1642/81 is output
      DTC B1642/81 and B1647/82 are not output

      Tech Tips

      Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    10. Return the door side airbag sensor LH and RH to their original positions and connect the connectors to them.


    DTC B1647/82 is output

    REPLACE DOOR SIDE AIRBAG SENSOR RH Click here

    DTC B1642/81 is output

    REPLACE AIR BAG SENSOR ASSEMBLY Click here

    DTC B1642/81 and B1647/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

  11. CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the airbag sensor assembly and rear airbag sensor LH.

      Result
      Proceed to
      The connectors are properly connected
      The connectors are not properly connected

    The connectors are not properly connected

    CONNECT CONNECTORS PROPERLY

    The connectors are properly connected

  12. CHECK CONNECTORS


    1. Disconnect the connectors from the airbag sensor assembly, rear airbag sensor LH and door side airbag sensor LH.

    2. A01V8UQC06
      *1 Rear Airbag Sensor LH
      *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire

      Check that the connectors (on the airbag sensor assembly side and rear airbag sensor LH side) are not damaged.

      Result
      Proceed to
      The connectors are not deformed or damaged
      The connectors are deformed or damaged

    The connectors are deformed or damaged

    REPLACE NO. 2 FLOOR WIRE

    The connectors are not deformed or damaged

  13. CHECK REAR AIRBAG SENSOR LH CIRCUIT


    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      A01V8FIC01
      *1 Rear Airbag Sensor LH *2 Airbag Sensor Assembly
      *3 No. 2 Floor Wire *4 Connector C
      *5 Connector B *6 Service Wire
      *a

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N9-4 (BCL+) - Body ground Ignition switch ON Below 1 V
      N9-3 (BCL-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 8 (BBL+) and 11 (BBL-) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N9-4 (BCL+) - N9-3 (BCL-) Always Below 1 Ω

    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N9-4 (BCL+) - N9-3 (BCL-) Always 1 MΩ or higher
      N9-4 (BCL+) - Body ground Always 1 MΩ or higher
      N9-3 (BCL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 2 FLOOR WIRE

    OK

  14. CHECK CONNECTION OF CONNECTOR


    1. Check that the connector is properly connected to the door side airbag sensor LH.

      Result
      Proceed to
      The connector is properly connected
      The connector is not properly connected

    The connector is not properly connected

    CONNECT CONNECTOR PROPERLY

    The connector is properly connected

  15. CHECK CONNECTOR


    1. Disconnect the connector from the door side airbag sensor LH.

    2. A01V9O9C05
      *1 Door Side Airbag Sensor LH
      *2 Rear Airbag Sensor LH

      Check that the connector (on the door side airbag sensor LH side) is not damaged.

      Result
      Proceed to
      The connector is not deformed or damaged
      The connector is deformed or damaged

    The connector is deformed or damaged

    REPLACE HARNESS AND CONNECTOR

    The connector is not deformed or damaged

  16. CHECK DOOR SIDE AIRBAG SENSOR LH CIRCUIT


    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      A01V9DRC03
      *1 Door Side Airbag Sensor LH *2 Rear Airbag Sensor LH
      *3 Connector E *4 Connector B
      *5 Service Wire - -
      *a

      Front view of wire harness connector

      (to Door Side Airbag Sensor LH)

      		 *b

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N9-1 (BDL+) - Body ground Ignition switch ON Below 1 V
      N9-2 (BDL-) - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 2 (BDL+) and 1 (BDL-) of connector E.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N9-1 (BDL+) - N9-2 (BDL-) Always Below 1 Ω

    8. Disconnect the service wire from connector E.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N9-1 (BDL+) - N9-2 (BDL-) Always 1 MΩ or higher
      N9-1 (BDL+) - Body ground Always 1 MΩ or higher
      N9-2 (BDL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE Click here

    OK

  17. CHECK REAR AIRBAG SENSOR LH


    1. A01V8MWC01
      *1 Rear Airbag Sensor RH
      *2 Airbag Sensor Assembly

      Connect the connectors to the airbag sensor assembly and door side airbag sensor LH.

    2. Interchange the rear airbag sensor LH with RH and connect the connectors to them.

    3. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    4. Turn the ignition switch to ON, and wait for at least 60 seconds.

    5. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    6. Turn the ignition switch off.

    7. Turn the ignition switch to ON, and wait for at least 90 seconds.

    8. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1642/81 is output
      DTC B1647/82 is output
      DTC B1642/81 and B1647/82 are not output

      Tech Tips

      Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.

    9. Turn the ignition switch off.

    10. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    11. Return the rear airbag sensor RH and LH to their original positions and connect the connectors to them.


    DTC B1642/81 is output

    REPLACE REAR AIRBAG SENSOR LH Click here

    DTC B1647/82 is output

    CHECK DOOR SIDE AIRBAG SENSOR LH Click here

    DTC B1642/81 and B1647/82 are not output

    USE SIMULATION METHOD TO CHECK Click here

  18. CHECK NO. 2 FLOOR WIRE


    1. Disconnect the No. 2 floor wire connector from the front door wire LH.

      A01V8CFC02
      *1 Door Side Airbag Sensor LH *2 Rear Airbag Sensor LH
      *3 Front Door Wire LH *4 No. 2 Floor Wire
      *5 Connector C *6 Connector B
      *7 Service Wire - -
      *a

      Front view of wire harness connector

      (to Front Door Wire LH)

      		 *b

      Front view of wire harness connector

      (to Rear Airbag Sensor LH)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N9-1 (BDL+) - Body ground Ignition switch ON Below 1 V
      N9-2 (BDL-) - Body ground Ignition switch ON Below 1 V

    5. Turn the ignition switch off.

    6. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    7. Using a service wire, connect terminals 3 (BDL+) and 1 (BDL-) of connector C.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N9-1 (BDL+) - N9-2 (BDL-) Always Below 1 Ω

    9. Disconnect the service wire from connector C.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N9-1 (BDL+) - N9-2 (BDL-) Always 1 MΩ or higher
      N9-1 (BDL+) - Body ground Always 1 MΩ or higher
      N9-2 (BDL-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT DOOR WIRE LH Click here

    NG

    REPLACE NO. 2 FLOOR WIRE

  19. CHECK DOOR SIDE AIRBAG SENSOR LH


    1. A01V700C15
      *1 Door Side Airbag Sensor RH
      *2 Rear Airbag Sensor LH

      Interchange the door side airbag sensor LH with RH and connect the connectors to them.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs stored in memory.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 90 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1642/81 is output
      DTC B1647/82 is output
      DTC B1642/81 and B1647/82 are not output

      Tech Tips

      Codes other than DTC B1642/81 and B1647/82 may be output at this time, but they are not related to this check.

    8. Turn the ignition switch off.

    9. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    10. Return the door side airbag sensor RH and LH to their original positions and connect the connectors to them.


    DTC B1642/81 is output

    REPLACE DOOR SIDE AIRBAG SENSOR LH Click here

    DTC B1647/82 is output

    REPLACE AIR BAG SENSOR ASSEMBLY Click here

    DTC B1642/81 and B1647/82 are not output

    USE SIMULATION METHOD TO CHECK Click here