AIRBAG SYSTEM(w/ Occupant Classification System), Diagnostic DTC:B1653/35

DTC Code DTC Name
B1653/35 Seat Position Airbag Sensor Circuit Malfunction

DESCRIPTION

The seat position airbag sensor circuit consists of the airbag sensor assembly and seat position airbag sensor.

DTC B1653/35 is stored when a malfunction is detected in the seat position airbag sensor circuit.

DTC No. Detection Item DTC Detection Condition Trouble Area
B1653/35 Seat Position Airbag Sensor Circuit Malfunction

    One of the following conditions is met:

  • The airbag sensor assembly detects a line short circuit signal, open circuit signal, short circuit to ground signal or short circuit to B+ signal in the seat position airbag sensor circuit for 2 seconds.

  • A seat position airbag sensor malfunction.

  • An airbag sensor assembly malfunction

  • No. 2 floor wire

  • Front seat inner belt assembly LH

  • Seat position airbag sensor

  • Airbag sensor assembly

WIRING DIAGRAM

A01V726E06
*a Seat Position Airbag Sensor
*b Front Seat Inner Belt Assembly LH
*c Airbag Sensor Assembly

CAUTION / NOTICE / HINT

Note


  • After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work.

    Click here

  • When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected.

    Click here

  • After replacing the airbag sensor assembly, refer to initialization.

    Click here

PROCEDURE


  1. CHECK CONNECTION OF CONNECTORS


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Check that the connectors are properly connected to the airbag sensor assembly and seat position airbag sensor.

      Result
      Proceed to
      Connectors are properly connected
      Connectors are not properly connected

    Connectors are not properly connected

    CONNECT CONNECTORS PROPERLY

    Connectors are properly connected

  2. CHECK CONNECTORS


    1. A01V7AEC01
      *1 Seat Position Airbag Sensor
      *2 Airbag Sensor Assembly

      Disconnect the connectors from the airbag sensor assembly and seat position airbag sensor.

    2. Check that the connectors (on the airbag sensor assembly side and seat position airbag sensor side) are not damaged.

      Click here

      Result
      Proceed to
      Connectors are not deformed or damaged
      Connectors are deformed or damaged

    Connectors are deformed or damaged

    REPLACE HARNESS AND CONNECTOR OR FRONT SEAT INNER BELT ASSEMBLY LH

    Connectors are not deformed or damaged

  3. CHECK SEAT POSITION AIRBAG SENSOR CIRCUIT


    1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

      A01V9B0C02
      *1 Seat Position Airbag Sensor *2 Airbag Sensor Assembly
      *3 Connector E *4 Connector B
      *5 Service Wire - -
      *a

      Front view of wire harness connector

      (to Seat Position Airbag Sensor)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      1 - Body ground Ignition switch ON Below 1 V
      2 - Body ground Ignition switch ON Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    6. Using a service wire, connect terminals 24 (LSP-) and 16 (LSP+) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    7. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always Below 1 Ω

    8. Disconnect the service wire from connector B.

    9. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 Always 1 MΩ or higher
      1 - Body ground Always 1 MΩ or higher
      2 - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    CHECK NO. 2 FLOOR WIRE Click here

    OK

  4. CHECK SEAT POSITION AIRBAG SENSOR


    1. A01V8C3C01
      *1 Seat Position Airbag Sensor
      *2 Airbag Sensor Assembly

      Connect the connectors to the airbag sensor assembly and seat position airbag sensor.

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON, and wait for at least 60 seconds.

    4. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    5. Turn the ignition switch off.

    6. Turn the ignition switch to ON, and wait for at least 60 seconds.

    7. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1653/35 is not output
      DTC B1653/35 is output

      Tech Tips

      Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.


    DTC B1653/35 is not output

    USE SIMULATION METHOD TO CHECK Click here

    DTC B1653/35 is output

  5. CHECK SEAT POSITION AIRBAG SENSOR


    1. Turn the ignition switch off.

    2. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    3. Replace the seat position airbag sensor.

      Click here

      Tech Tips

      Perform the inspection using parts from a normal vehicle if possible.

      Result
      Proceed to
      NEXT

    NEXT

  6. CHECK AIRBAG SENSOR ASSEMBLY


    1. A01V8C3C01
      *1 Seat Position Airbag Sensor
      *2 Airbag Sensor Assembly

      Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    2. Turn the ignition switch to ON, and wait for at least 60 seconds.

    3. Clear the DTCs.

      Click here


      Body Electrical > SRS Airbag > Clear DTCs

    4. Turn the ignition switch off.

    5. Turn the ignition switch to ON, and wait for at least 60 seconds.

    6. Check for DTCs.

      Click here


      Body Electrical > SRS Airbag > Trouble Codes
      Result
      Proceed to
      DTC B1653/35 is not output
      DTC B1653/35 is output

      Tech Tips

      Codes other than DTC B1653/35 may be output at this time, but they are not related to this check.


    DTC B1653/35 is not output

    END (SEAT POSITION AIRBAG SENSOR WAS DEFECTIVE)

    DTC B1653/35 is output

    REPLACE AIRBAG SENSOR ASSEMBLY Click here

  7. CHECK NO. 2 FLOOR WIRE


    1. Disconnect the No. 2 floor wire connector from the front seat inner belt assembly LH.

      A01VA2HC02
      *1 Seat Position Airbag Sensor *2 Airbag Sensor Assembly
      *3 Front Seat Inner Belt Assembly LH *4 No. 2 Floor Wire
      *5 Connector C *6 Connector B
      *7 Service Wire - -
      *a

      Front view of wire harness connector

      (to Front Seat Inner Belt Assembly LH)

      		 *b

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)

    2. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

    3. Turn the ignition switch to ON.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      N14-4 (LSP+) - Body ground Ignition switch ON Below 1 V
      N14-3 (LSP-) - Body ground Ignition switch ON Below 1 V

    5. Turn the ignition switch off.

    6. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

    7. Using a service wire, connect terminals 24 (LSP-) and 16 (LSP+) of connector B.

      Note

      Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

    8. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N14-4 (LSP+) - N14-3 (LSP-) Always Below 1 Ω

    9. Disconnect the service wire from connector B.

    10. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      N14-4 (LSP+) - N14-3 (LSP-) Always 1 MΩ or higher
      N14-4 (LSP+) - Body ground Always 1 MΩ or higher
      N14-3 (LSP-) - Body ground Always 1 MΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE FRONT SEAT INNER BELT ASSEMBLY LH Click here

    NG

    REPLACE NO. 2 FLOOR WIRE