THEFT DETERRENT SYSTEM, Diagnostic DTC:B276A

DTC Code DTC Name
B276A Short to GND in Tilt Sensor Signal Circuit

DESCRIPTION

This DTC is stored when terminal CSIF of the tilt sensor (yaw rate sensor assembly) has not received a signal for 5 seconds or more.

This DTC is stored when terminal CSIF of the tilt sensor (yaw rate sensor) has not received a signal for 5 seconds or more.
DTC No. Detection Item DTC Detection Condition Trouble Area
B276A Short to GND in Tilt Sensor Signal Circuit Terminal CSIF of tilt sensor (yaw rate sensor assembly) has not received signal for 5 seconds or more

  • Tilt sensor (yaw rate sensor assembly)

  • Main body ECU (multiplex network body ECU)

  • Harness or connector

WIRING DIAGRAM

A01V8W9E01
*a from Battery
*b ECU-B NO.1
*c Tilt Sensor (Yaw Rate Sensor Assembly)
*d Main Body ECU (Multiplex Network Body ECU)

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • When replacing the main body ECU (multiplex network body ECU), make sure to replace it with a new one.

PROCEDURE


  1. CHECK WAVEFORM (TILT SENSOR [YAW RATE SENSOR ASSEMBLY]) (CSIF)


    1. Using an oscilloscope, check the waveform.

      A01V9Y6C05
      *a

      Component with harness connected

      (Main Body ECU [Multiplex Network Body ECU])

      		 *b CSIF Initial Signal
      *c CSIF Initial Response *d Approximately 1.0 seconds
      *e Initial Diagnosis *f Approximately 1.0 to 1.6 seconds
      *g Approximately 0.05 seconds *h Approximately 5.5 seconds
      *i Disarmed State *j Arming Preparation State
      *k HI *l LO
      Measurement Condition
      Tester Connection Content
      Tester Connection G79-6 (GCS) - Body ground
      Tool Setting 2 V/DIV., 100 ms./DIV.
      Condition Theft deterrent system is set (system changes from disarmed state to arming preparation state)

      Tech Tips


      • If the tilt sensor (yaw rate sensor assembly) is normal, an initial response is output in response to the HI input from the main body ECU (multiplex network body ECU).

      • If the waveform output remains LO, there may be a problem with the main body ECU (multiplex network body ECU), as there is no input from the main body ECU (multiplex network body ECU).

      OK
      The waveform displays properly (HI is 6.5 V or higher and LO is below 1 V).
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. CHECK VOLTAGE (TILT SENSOR [YAW RATE SENSOR ASSEMBLY]) (CSIF)


    1. A01VATHC02
      *a

      Front view of wire harness connector

      (to Tilt Sensor [Yaw Rate Sensor Assembly])

      Disconnect the tilt sensor (yaw rate sensor assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition
      N16-5 (CSIF) - N16-1 (GND) Immediately after theft deterrent system set
      Result
      Result Proceed to
      CSIF voltage is below 1 V when theft deterrent system is set A
      CSIF voltage is 6.5 V or higher when theft deterrent system is set B

      Tech Tips

      With connector N16 of the tilt sensor (yaw rate sensor assembly) disconnected, measure the voltage at CSIF when the theft deterrent system is set.


    B

    REPLACE TILT SENSOR (YAW RATE SENSOR ASSEMBLY) Click here

    A

  3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - TILT SENSOR [YAW RATE SENSOR ASSEMBLY])


    1. Disconnect the G79 main body ECU (multiplex network body ECU) connector.

    2. Disconnect the N16 tilt sensor (yaw rate sensor assembly) connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G79-6 (GCS) - N16-5 (CSIF) Always Below 1 Ω
      G79-6 (GCS) - Body ground Always 10 kΩ or higher
      N16-5 (CSIF) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR