ENTRY AND START SYSTEM(for Start Function) Power Source Mode does not Change to ON (IG and ACC)

DESCRIPTION

If any of the following operations are performed, the certification ECU (smart key ECU assembly) receives a signal, and changes the power source mode.


Tech Tips


  • When the cable is disconnected and reconnected to the negative (-) battery terminal, the power source mode returns to the state it was in before the cable was disconnected.

  • If the room oscillator does not recognize the key, the cause of the malfunction may be stored in the certification ECU (smart key ECU assembly).

  • If the cause of the malfunction is stored in the certification ECU (smart key ECU assembly), the following table is helpful in checking whether or not the malfunction was caused by wave interference.

Radio Wave Interference:
Problem Symptom Data List Item
Operating Engine Switch / Key RF Signal Interference

When the engine switch was operated, the electrical key transmitter sub-assembly could not be confirmed due to wave interference. Therefore, the output frequency was switched to the other channel (changed from channel 1 to channel 2 or from channel 2 to channel 1).

If the cause of the malfunction has not been stored but any devices that can cause wave interference in the cabin have been removed and the room oscillator successfully recognizes the key, the possibility of wave interference is high.
Related Data List and Active Test Items
Problem Symptom Data List Item Active Test Item
Power source mode does not change to on (IG) or on (ACC)

    Power Source Control:

  • Start Switch1

  • Start Switch2

  • Power Supply Condition

  • IG1 Relay Monitor(Inside)

  • IG2 Relay Monitor(Inside)

  • IG1 Relay Monitor(Outside)

  • IG2 Relay Monitor(Outside)

  • Latch Circuit

  • ACC Relay Monitor

 -

WIRING DIAGRAM

A01KAUXE01

CAUTION / NOTICE / HINT

Note


  • When using the GTS with the engine switch off to troubleshoot:

    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5 second intervals until communication between the GTS and vehicle begins.

  • The entry and start system (for Start Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting Click here. Troubleshoot the entry and start system (for Start Function) after confirming that the communication systems are functioning properly.

  • Make sure that no DTCs are output. If any DTCs are output, proceed to the Diagnostic Trouble Code Chart.

    Click here

  • If the entry and start system is disabled through the customize function, enable the system before performing troubleshooting.

    Click here

  • Before replacing the certification ECU (smart key ECU assembly), electrical key transmitter sub-assembly or ID code box (immobiliser code ECU) (w/ Multi-information Display (Dot Display Type)), refer to the entry and start system (for Start Function) precaution.

    Click here

  • Inspect the fuses of circuits related to this system before performing the following inspection procedure.

  • After completing repairs, confirm that the problem does not occur.

PROCEDURE


  1. CHECK WIRELESS DOOR LOCK CONTROL SYSTEM


    1. Check the wireless door lock function by operating the electrical key transmitter sub-assembly.

      OK
      Wireless door lock function operates
      Result
      Proceed to
      OK
      NG

    NG

    GO TO OTHER FLOWCHART (All Door Entry Lock/Unlock Functions and Wireless Functions do not Operate) Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (POWER SOURCE)


    1. A01KDEKC36
      *a

      Rear view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      Disconnect the G82 certification ECU (smart key ECU assembly) connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G82-2 (+B) - Body ground Always 11 to 14 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (CONNECTOR IN CIRCUIT CONNECTED TO POWER SOURCE)

    OK

  3. CHECK HARNESS AND CONNECTOR (GROUND)


    1. A01KDEKC40
      *a

      Rear view of wire harness connector

      (to Certification ECU (Smart Key ECU Assembly))

      Disconnect the G82 certification ECU (smart key ECU assembly) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G82-11 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK ENGINE SWITCH FUNCTION


    1. Remove the battery from the electrical key transmitter sub-assembly.

      Click here

    2. A01KC4B

      With the brake pedal*1 or clutch pedal*2 depressed, hold the electrical key transmitter near the engine switch and check if the power source mode changes.


      • *1: except Manual Transaxle

      • *2: for Manual Transaxle

      Tech Tips

      If the power source mode changes, the cabin verification is malfunctioning.

      OK
      The power source mode changes.
      Result
      Proceed to
      The power source mode does not change
      The power source mode changes

    The power source mode changes

    READ VALUE USING GTS (START SWITCH 1, 2) Click here

    The power source mode does not change

  5. READ VALUE USING GTS (STOP LIGHT SWITCH 1, NEUTRAL SW/CLUTCH SW)


    1. except Manual Transaxle:


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body / Power Source Control / Data List.

      5. According to the display on the GTS, read the Data List.


        Body Electrical > Power Source Control > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Stop Light Switch1 State of brake pedal ON or OFF

        ON: Brake pedal depressed

        OFF: Brake pedal released

        • Use this item to determine whether the stop light switch is malfunctioning.

        • The engine cannot be started when this item is "OFF".

        • When this item is malfunctioning, the engine can be started by pressing and holding the engine switch for a certain period of time.

        Body Electrical > Power Source Control > Data List
        Tester Display
        Stop Light Switch1
        OK
        ON (brake pedal depressed) and OFF (brake pedal released) appear on the screen according to the stop light switch condition.

    2. for Manual Transaxle:


      1. Connect the GTS to the DLC3.

      2. Turn the engine switch on (IG).

      3. Turn the GTS on.

      4. Enter the following menus: Body / Power Source Control / Data List.

      5. According to the display on the GTS, read the Data List.


        Body Electrical > Power Source Control > Data List
        Tester Display Measurement Item Range Normal Condition Diagnostic Note
        Neutral SW/ Clutch SW State of clutch pedal ON or OFF

        ON: Clutch pedal depressed

        OFF: Clutch pedal released

        • Use this item to determine whether the clutch switch is malfunctioning.

        • The engine cannot be started when this item is "OFF".

        Body Electrical > Power Source Control > Data List
        Tester Display
        Neutral SW/ Clutch SW
        OK
        ON (clutch pedal depressed) and OFF (clutch pedal released) appear on the screen according to the stop light switch condition.
        Result
        Proceed to
        OK
        NG (except Manual Transaxle)
        NG (for Manual Transaxle)

    NG (except Manual Transaxle)

    CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY) Click here

    NG (for Manual Transaxle)

    INSPECT CLUTCH START SWITCH ASSEMBLY Click here

    OK

  6. READ VALUE USING GTS (POWER SUPPLY CONDITION)


    1. Read the Data List according to the display on the GTS.


      Body Electrical > Power Source Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON

      ALL OFF: Engine switch off

      ACC ON: Engine switch on (ACC) (ACC relay on)

      IG1 ON: Engine switch on (IG) (IG1 relay on)

      IG2 ON: Engine switch on (IG) (IG2 relay on)

      ST ON: Sending engine start request signal

      		 Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

      Body Electrical > Power Source Control > Data List
      Tester Display
      Power Supply Condition

    2. With the engine switch off and brake pedal depressed, hold the electrical key transmitter sub-assembly near the engine switch for 2 seconds or more and read the Data List.

      Tech Tips

      If the entry key function has been canceled on the customization menu, ACC ON is displayed in the Data List.

      OK
      IG2 ON is displayed in the Data List.
      Result
      Proceed to
      OK
      NG

    NG

    CHECK FOR DTC Click here

    OK

  7. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)


    1. Measure the voltage while checking the Data List on the GTS.

      A01KCEOC39
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      		 - -

      Body Electrical > Power Source Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Power Supply Condition Power supply state IG2 ON, ST ON, All OFF, IG1 ON or ACC ON

      All OFF: Engine switch off (ACC and IG)

      ACC ON: Engine switch on (ACC)

      IG1 ON: Engine switch on (IG) (IG1 relay on)

      IG2 ON: Engine switch on (IG) (IG2 relay on)

      ST ON: Sending engine start request signal

      		 Since the IG1 and IG2 relays turn on at approximately the same time, IG1 ON may not be displayed (the IG1 relay turns on for a very short time).

      Body Electrical > Power Source Control > Data List
      Tester Display
      Power Supply Condition
      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G84-6 (IG1D) - Body ground Engine switch off 1 V or less
      Engine switch on (ACC)
      Engine switch on (IG) 9 V or higher
      G82-9 (IG2D) - Body ground Engine switch off 1 V or less
      Engine switch on (ACC)
      Engine switch on (IG) 9 V or higher
      G84-4 (ACCD) - Body ground Engine switch off 1 V or less
      Engine switch on (IG) 8.5 V or higher
      Engine switch on (ACC)
      Result
      Proceed to
      OK
      NG

    OK

    CHECK RELAY CONTACT SIDE CIRCUIT Click here

    NG

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

  8. CHECK FOR DTC


    1. Enter the following menus: Body Electrical / Entry&Start / Trouble Codes.

    2. Check for DTCs.


      Body Electrical > Entry&Start > Trouble Codes
      Result
      Result Proceed to

        The following DTCs are not output:

      • B2784

      • B287A

      		 A
      DTC B2784 is output. B
      DTC B278A is output. C

    A

    REPLACE ELECTRICAL KEY TRANSMITTER SUB-ASSEMBLY Click here

    B

    GO TO OTHER FLOWCHART (DTC B2784) Click here

    C

    GO TO OTHER FLOWCHART (DTC B278A) Click here

  9. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - STOP LIGHT SWITCH ASSEMBLY)


    1. Disconnect the A5 connector from the stop light switch assembly.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G82-18 (STP1) - A5-1 Always Below 1 Ω
      G82-18 (STP1) or A5-1- Body ground 10 kΩ or higher
    3. A01KAKDC11
      *a

      Component with harness connected

      (Certification ECU (Smart Key ECU Assembly))

      Reconnect the A5 connector from the stop light switch assembly.

    4. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      G82-18 (STP1) - Body ground Brake pedal released 1 V or less
      Brake pedal depressed 9 V or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  10. INSPECT STOP LIGHT SWITCH ASSEMBLY


    1. Disconnect the A5 connector from the stop light switch assembly.

    2. Inspect the stop light switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPLACE STOP LIGHT SWITCH ASSEMBLY Click here

  11. INSPECT CLUTCH START SWITCH ASSEMBLY


    1. Inspect the clutch start switch assembly.

      Click here

      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CLUTCH START SWITCH ASSEMBLY Click here

    OK

  12. INSPECT ST RELAY (STARTER RELAY ASSEMBLY)


    1. Inspect the ST relay (starter relay assembly).


      Result
      Proceed to
      OK
      NG

    NG

    REPLACE ST RELAY (STARTER RELAY ASSEMBLY)

    OK

  13. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - CLUTCH START SWITCH ASSEMBLY)


    1. Disconnect the G82 certification ECU (smart key ECU assembly) connector.

    2. Disconnect the A4 or F2 clutch start switch connector

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for RHD
      Tester Connection Condition Specified Condition
      G82-5 (STAR) - F2-2 Always Below 1 Ω
      G82-5 (STAR) or F2-2 - Body ground Always 10 kΩ or higher
      for LHD
      Tester Connection Condition Specified Condition
      G82-5 (STAR) - A4-2 Always Below 1 Ω
      G82-5 (STAR) or A4-2 - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  14. CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH ASSEMBLY - ST RELAY (STARTER RELAY ASSEMBLY))


    1. Disconnect the A4 or F2 clutch start switch assembly connector.

    2. Remove the ST relay (starter relay assembly) from the No. 2 engine room relay block assembly.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      for LHD
      Tester Connection Condition Specified Condition
      A4-1 - 2 Always Below 1 Ω
      1 - Body ground Below 1 Ω
      A4-1 or 2 - Body ground 10 kΩ or higher
      for RHD
      Tester Connection Condition Specified Condition
      F2-1 - 2 Always Below 1 Ω
      1 - Body ground Below 1 Ω
      F2-1 or 2 - Body ground 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

  15. READ VALUE USING GTS (START SWITCH 1, 2)


    1. Read the Data List according to the display on the GTS.


      Body Electrical > Power Source Control > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Start Switch1 Engine switch 1 status ON or OFF

      ON: Engine switch pressed

      OFF: Engine switch not pressed

      • If the engine switch is pressed for a short time, the display may not change.

      • Use this item to determine whether the engine switch input signal is malfunctioning.
      Start Switch2 Engine switch 2 status ON or OFF

      ON: Engine switch pressed

      OFF: Engine switch not pressed

      • Backup for engine switch 1. However, when the engine switch is pressed and held, the control functions only when both engine switch 1 and 2 are normal.

      • Behaves the same way as engine switch 1.

      Body Electrical > Power Source Control > Data List
      Tester Display
      Start Switch1
      Start Switch2
      OK
      ON (Engine switch is pressed) and OFF (Engine switch is not pressed) appear on the screen.
      Result
      Proceed to
      OK
      NG

    OK

    GO TO OTHER FLOWCHART (Room Oscillator does not Recognize Key) Click here

    NG

  16. INSPECT ENGINE SWITCH


    1. Inspect the engine switch.


      Result
      Proceed to
      OK
      NG (for 1AD-FTV)
      NG (for 2AD-FHV)
      NG (for 2AD-FTV)
      NG (for 2AR-FE)
      NG (for 3ZR-FAE)
      NG (for 3ZR-FE)

    NG (for 1AD-FTV)

    REPLACE ENGINE SWITCH Click here

    NG (for 2AD-FHV)

    REPLACE ENGINE SWITCH Click here

    NG (for 2AD-FTV)

    REPLACE ENGINE SWITCH Click here

    NG (for 2AR-FE)

    REPLACE ENGINE SWITCH Click here

    NG (for 3ZR-FAE)

    REPLACE PUSH START SWITCH Click here

    NG (for 3ZR-FE)

    REPLACE PUSH START SWITCH Click here

    OK

  17. CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - ENGINE SWITCH)


    1. Disconnect the G84 connector from the certification ECU (smart key ECU assembly).

    2. Disconnect the G24 connector from the engine switch.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G84-28 (SSW1) - G24-5 (SS1) Always Below 1 Ω
      G84-30 (SSW2) - G24-1 (SS2)
      G84-28 (SSW1) or G24-5 (SS1) - Body ground 10 kΩ or higher
      G84-30 (SSW2) or G24-1 (SS2) - Body ground
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR