WIRELESS DOOR LOCK CONTROL SYSTEM(w/o Entry and Start System) Only Wireless Control Function is Inoperative

DESCRIPTION

The door control receiver receives signals from the door control transmitter assembly and sends these signals to the main body ECU (multiplex network body ECU). The main body ECU (multiplex network body ECU) then controls all doors by sending lock/unlock signals to each door, and sends hazard flasher signals to the combination meter assembly.

WIRING DIAGRAM

1. for 12 Pin Type

   

2. except 12 Pin Type

   

3. except 12 Pin Type (w/ Tire Pressure Warning ECU [ECE-R64 Type])

   

CAUTION / NOTICE / HINT

• *1: for 12 Pin Type

• *2: except 12 Pin Type (w/ Tire Pressure Warning ECU [ECE-R64 Type])

PROCEDURE

1. CHECK POWER DOOR LOCK OPERATION

   
   

   1. Check the power door lock operation.

      Click here

      Result
      Proceed to Locked doors unlock Locked doors do not unlock

   
   

   Locked doors do not unlock

   GO TO POWER DOOR LOCK CONTROL SYSTEM Click here

   Locked doors unlock

2. CHECK KEY REMINDER WARNING SYSTEM

   
   

   1. Check that the key reminder warning buzzer operates properly.

      Click here

      Result
      Proceed to Key reminder warning buzzer operates properly Key reminder warning buzzer does not operates properly

   
   

   Key reminder warning buzzer does not operates properly

   GO TO KEY REMINDER WARNING SYSTEM Click here

   Key reminder warning buzzer operates properly

3. CHECK DOOR CONTROL TRANSMITTER ASSEMBLY

   
   

   1. When a known good registered door control transmitter assembly is used, check that the wireless functions operate properly.

      Click here

      Result
      Result Proceed to Wireless door lock/unlock/back door open function operates properly with a known good door control transmitter assembly. A Wireless door lock/unlock/back door open function does not operate. B

   
   

   B

   CHECK WAVE ENVIRONMENT Click here

   A

4. CHECK TRANSMITTER BATTERY (VOLTAGE)

   
   

   1. Remove the transmitter battery.

      Click here

   2. Inspect the transmitter battery capacity.

      Click here

      Result
      Proceed to OK NG

   
   

   OK

   REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

   NG

   REPLACE TRANSMITTER BATTERY Click here

5. CHECK WAVE ENVIRONMENT

   
   

   1. Bring the door control transmitter assembly near the door control receiver, and perform a wireless operation check.

      Tech Tips

      
      

      • When the door control transmitter assembly is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.

      • If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

      Result
      Proceed to Wireless functions operate properly Wireless functions do not operate properly

   
   

   Wireless functions operate properly

   END (AFFECTED BY WAVE INTERFERENCE)

   Wireless functions do not operate properly

6. SWITCH TO SELF-DIAGNOSTIC MODE

   
   

   1. Using GTS

      
      

      1. Connect the GTS to the DLC3.

      2. Turn the Ignition switch to ON.

      3. Enter the following menus: Body Electrical / Main Body / Utility / Wireless Diagnosis Mode.

         
         Body Electrical > Main Body > Utility

         Tester Display
         Wireless Door Lock Diagnosis Mode

      4. Proceed to the next step in accordance with the prompts on the GTS screen.

      5. 

         Interior Light Output

         *1	On
         *2	Off
         *3	T1: 0.25 seconds
         *4	T2: 0.5 seconds

         Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.

   2. Not using GTS (w/ Manual Diagnosis Mode)

      
      

      1. Insert and remove the key into/from the ignition key cylinder one time (Insert → Remove → Insert → Remove) and then ignition switch turn ON to off within 5 seconds.

      2. Perform the following operations within 30 seconds.

         (1) Turn the ignition switch from ON to off at nine times.

      3. 

         Interior Light Output

         *1	On
         *2	Off
         *3	T1: 0.25 seconds
         *4	T2: 0.5 seconds

         Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.

      Result
      Proceed to NEXT

   
   

   NEXT

7. CHECK SELF DIAGNOSTIC MODE

   
   

   1. Inspect the diagnostic outputs when the door control transmitter assembly switch is pressed. The diagnostic outputs can be checked by the flash patterns of the interior lights.

      

      Result
      Result Proceed to Normal wave (light flash pattern) is output (A). A Unmatching recognition code is output (B). B No diagnostic outputs (C). C

   
   

   A

   REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for LHD: Click here REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for RHD: Click here

   C

   CHECK DOOR CONTROL RECEIVER (RESPONSE) Click here

   B

8. CHECK REGISTER RECOGNITION CODE

   
   

   1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

      Click here

      Result
      Proceed to Recognition code can be registered Recognition code cannot be registered

   
   

   Recognition code can be registered

   END (GO TO OPERATION CHECK)

   Recognition code cannot be registered

   GO TO STEP 13 Click here

9. CHECK DOOR CONTROL RECEIVER (RESPONSE)

   
   

   1. Prepare the door control transmitter assembly from another vehicle.

   2. Press and hold down the door control transmitter assembly switch.

   3. Check that an unmatching recognition code is output.

      Result
      Proceed to Unmatching recognition code is output Unmatching recognition code is not output

   
   

   Unmatching recognition code is output

   REPLACE DOOR CONTROL TRANSMITTER ASSEMBLY

   Unmatching recognition code is not output

10. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - BATTERY AND BODY GROUND)

    
    
    1. 

       *a	Front view of wire harness connector (to Tire Pressure Warning ECU and Receiver)

       for 12 Pin Type:

       
       

       1. Disconnect the M11 door control receiver.

       2. Measure the resistance according to the value(s) in the table below.

          Standard Resistance
          Tester Connection Condition Specified Condition M11-12 (E) - Body ground Always Below 1 Ω

       3. Measure the voltage according to the value(s) in the table below.

          Standard Voltage
          Tester Connection Condition Specified Condition M11-7 (+B) - Body ground Always 11 to 14 V

    2. 

       *a	Front view of wire harness connector (to Door Control Receiver)

       except 12 Pin Type:

       
       

       1. Disconnect the M10 door control receiver.

       2. Measure the resistance according to the value(s) in the table below.

          Standard Resistance
          Tester Connection Condition Specified Condition M10-1 (GND) - Body ground Always Below 1 Ω

       3. Measure the voltage according to the value(s) in the table below.

          Standard Voltage
          Tester Connection Condition Specified Condition M10-5 (DATA) - Body ground Always 11 to 14 V

       Result
       Proceed to OK NG

    
    

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

11. CHECK DOOR CONTROL RECEIVER (OUTPUT)

    
    

    1. for 12 Pin Type:

       
       

       1. Connect the M11 door control receiver.

       2. 

          *a	Component with harness connected (Door Control Receiver)

          Measure the voltage according to the value(s) in the table below.

          Standard Voltage
          Tester Connection Condition Specified Condition M11-4 (RDA) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V Ignition switch lock, all doors closed and door control transmitter assembly switch pressed Pulse generation (0 to 12 V)

    2. except 12 Pin Type:

       
       

       1. Connect the M10 door control receiver.

       2. 

          *a	Component with harness connected (Door Control Receiver)

          Measure the voltage according to the value(s) in the table below.

          Standard Voltage
          Tester Connection Condition Specified Condition M10-2 (CSEL) - Body ground Ignition switch lock, all doors closed and door control transmitter assembly switch not pressed 11 to 14 V Ignition switch lock, all doors closed and door control transmitter assembly switch pressed Pulse generation (0 to 12 V)

       Result
       Result Proceed to OK (for 12 Pin Type) A OK (except 12 Pin Type) B OK (except 12 Pin Type [w/ Tire Pressure Warning ECU (ECE-R64 Type)]) C NG D

    
    

    B

    CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DOOR CONTROL RECEIVER) Click here

    C

    CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - TIRE PRESSURE WARNING ECU AND RECEIVER) Click here

    D

    REPLACE DOOR CONTROL RECEIVER Click here

    A

12. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DOOR CONTROL RECEIVER)

    
    

    1. Disconnect the G78 main body ECU (multiplex network body ECU) connector.

    2. Disconnect the M11 door control receiver connector.

    3. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition M11-4 (RDA) - G78-16 (RDA) Always Below 1 Ω M11-5 (PRG) - G78-4 (PRG) Always Below 1 Ω M11-4 (RDA) - Body ground Always 10 kΩ or higher G78-16 (RDA) - Body ground Always 10 kΩ or higher M11-5 (PRG) - Body ground Always 10 kΩ or higher G78-4 (PRG) - Body ground Always 10 kΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

13. REPLACE DOOR CONTROL RECEIVER

    
    

    1. Temporarily replace the door control receiver with a new or known good one.

       Click here

       Result
       Proceed to NEXT

    
    

    NEXT

14. CHECK REGISTER RECOGNITION CODE

    
    

    1. Perform the Registration procedure.

       Click here

       Result
       Proceed to NEXT

    
    

    NEXT

15. CHECK DOOR CONTROL RECEIVER (OPERATION)

    
    

    1. Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

       OK
       Doors can be locked and unlocked by the door control transmitter assembly.

       Result
       Proceed to OK NG

    
    

    OK

    END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for LHD: Click here REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for RHD: Click here

16. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU] - DOOR CONTROL RECEIVER)

    
    

    1. Disconnect the G78 main body ECU (multiplex network body ECU) connector.

    2. Disconnect the M10 door control receiver connector.

    3. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition M10-2 (CSEL) - G78-16 (RDA) Always Below 1 Ω M10-3 (PRG) - G78-4 (PRG) Always Below 1 Ω M10-2 (CSEL) - Body ground Always 10 kΩ or higher G78-16 (RDA) - Body ground Always 10 kΩ or higher M10-3 (PRG) - Body ground Always 10 kΩ or higher G78-4 (PRG) - Body ground Always 10 kΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

17. REPLACE DOOR CONTROL RECEIVER

    
    

    1. Temporarily replace the door control receiver with a new or known good one.

       Click here

       Result
       Proceed to NEXT

    
    

    NEXT

18. CHECK REGISTER RECOGNITION CODE

    
    

    1. Perform the Registration procedure.

       Click here

       Result
       Proceed to NEXT

    
    

    NEXT

19. CHECK DOOR CONTROL RECEIVER (OPERATION)

    
    

    1. Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

       OK
       Doors can be locked and unlocked by the door control transmitter assembly.

       Result
       Proceed to OK NG

    
    

    OK

    END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for LHD: Click here REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for RHD: Click here

20. CHECK HARNESS AND CONNECTOR (DOOR CONTROL RECEIVER - TIRE PRESSURE WARNING ECU AND RECEIVER)

    
    

    1. Disconnect the M10 door control receiver connector.

    2. Disconnect the M30 tire pressure warning ECU and receiver connector.

    3. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition M10-2 (CSEL) - M30-10 (RDA3) Always Below 1 Ω M10-3 (PRG) - M30-9 (PRG3) Always Below 1 Ω M10-2 (CSEL) - Body ground Always 10 kΩ or higher M30-10 (RDA3) - Body ground Always 10 kΩ or higher M10-3 (PRG) - Body ground Always 10 kΩ or higher M30-9 (PRG3) - Body ground Always 10 kΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

21. CHECK HARNESS AND CONNECTOR (TIRE PRESSURE WARNING ECU AND RECEIVER - MAIN BODY ECU [MULTIPLEX NETWORK BODY ECU])

    
    

    1. Disconnect the M30 tire pressure warning ECU and receiver connector.

    2. Disconnect the G78 main body ECU (multiplex network body ECU) connector.

    3. Measure the resistance according to the value(s) in the table below.

       Standard Resistance
       Tester Connection Condition Specified Condition M30-4 (RDA2) - G78-16 (RDA) Always Below 1 Ω M30-5 (PRG2) - G78-4 (PRG) Always Below 1 Ω M30-4 (RDA2) - Body ground Always 10 kΩ or higher G78-16 (RDA) - Body ground Always 10 kΩ or higher M30-5 (PRG2) - Body ground Always 10 kΩ or higher G78-4 (PRG) - Body ground Always 10 kΩ or higher

       Result
       Proceed to OK NG

    
    

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

22. REPLACE DOOR CONTROL RECEIVER

    
    

    1. Temporarily replace the door control receiver with a new or known good one.

       Click here

       Result
       Proceed to NEXT

    
    

    NEXT

23. CHECK REGISTER RECOGNITION CODE

    
    

    1. Perform the Registration procedure.

       Click here

       Result
       Proceed to NEXT

    
    

    NEXT

24. CHECK DOOR CONTROL RECEIVER (OPERATION)

    
    

    1. Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

       OK
       Doors can be locked and unlocked by the door control transmitter assembly.

       Result
       Proceed to OK NG

    
    

    OK

    END (DOOR CONTROL RECEIVER WAS DEFECTIVE)

    NG

25. REPLACE TIRE PRESSURE WARNING ECU AND RECEIVER

    
    

    1. Temporarily replace the tire pressure warning ECU and receiver with a new or known good one.

       Click here

       Result
       Proceed to NEXT

    
    

    NEXT

26. CHECK REGISTER RECOGNITION CODE

    
    

    1. Perform the Registration procedure.

       Click here

       Result
       Proceed to NEXT

    
    

    NEXT

27. CHECK DOOR CONTROL RECEIVER (OPERATION)

    
    

    1. Check that the doors can be locked and unlocked by the door control transmitter assembly lock and unlock switches.

       OK
       Doors can be locked and unlocked by the door control transmitter assembly.

       Result
       Proceed to OK NG

    
    

    OK

    END (TIRE PRESSURE WARNING ECU AND RECEIVER WAS DEFECTIVE)

    NG

    REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for LHD: Click here REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) for RHD: Click here