SPIRAL CABLE(for Single Type) INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips


  • Use the same procedure for the driver side of RHD and LHD vehicles.

  • The procedures listed below are for the driver side of LHD vehicles.

PROCEDURE


  1. INSPECT SPIRAL CABLE SUB-ASSEMBLY


    1. A01KB74C01
      *1 Alignment Mark
      *2 Colored Roller (Yellow)

      Check if the spiral cable sub-assembly is centered.

      Tech Tips

      When the spiral cable sub-assembly is centered, the alignment marks are aligned and the colored roller (yellow) or flat cable shown in the illustration is visible.

    2. If the spiral cable sub-assembly is not centered, center it.

      If the cable cannot be centered, it is possible that the spiral cable sub-assembly is broken. Replace the spiral cable sub-assembly with a new one.


      1. A01KD8IC04
        *1 Interlock

        While pushing on the interlock indicated in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

        Note


        • When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable sub-assembly using the airbag wire harness.

      2. A01KBBZ

        Rotate the spiral cable sub-assembly approximately 2.5 rotations in the clockwise direction from the locked position until the colored roller (yellow) or flat cable can be seen, and then align the alignment marks.

        Tech Tips

        The spiral cable sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.

  2. INSTALL SPIRAL CABLE SUB-ASSEMBLY

    Note


    • Do not replace the spiral cable sub-assembly with the battery connected and the ignition switch on (IG).

    • Do not rotate the spiral cable sub-assembly with the battery connected and the ignition switch on (IG).

    • w/ Vehicle Stability Control System:

      Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. Check that the front wheels are facing straight ahead.

    4. Attach the 3 claws to install the spiral cable sub-assembly.

      Note

      When replacing the spiral cable sub-assembly with a new one, remove the lock pin before installing the steering wheel assembly.

    5. Connect the connector to the spiral cable sub-assembly.

      Note

      When connecting any airbag connector, take care not to damage the airbag wire harness.

  3. INSTALL STEERING COLUMN COVER

    Click here

  4. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD

  5. ADJUST SPIRAL CABLE SUB-ASSEMBLY

    Note

    Do not adjust the spiral cable with the battery connected and the ignition switch on (IG).


    1. Check that the ignition switch is off.

    2. Check that the cable is disconnected from the negative (-) battery terminal.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    3. A01KB74C01
      *1 Alignment Mark
      *2 Colored Roller (Yellow)

      Check if the spiral cable sub-assembly is centered.

      Tech Tips

      When the spiral cable sub-assembly is centered, the alignment marks are aligned and the colored roller (yellow) or flat cable shown in the illustration is visible.

    4. If the spiral cable sub-assembly is not centered, center it.


      1. A01KDOTC01
        *1 Interlock

        While pushing on the interlock indicated in the illustration, rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.

        Note


        • When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable sub-assembly using the airbag wire harness.

      2. A01KCDXC01
        *1 Interlock

        While pushing on the interlock indicated, rotate the spiral cable sub-assembly clockwise approximately 2.5 turns to the position where the colored roller (yellow) or flat cable is visible.

        Note


        • When rotating the spiral cable sub-assembly, make sure to push on the interlock indicated in the illustration to release the interlock mechanism.

        • Do not turn the spiral cable sub-assembly using the airbag wire harness.

        Tech Tips

        The spiral cable will rotate approximately 2.5 turns to both the left and right from the center.

  6. INSTALL STEERING WHEEL ASSEMBLY

    Click here

  7. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  8. PERFORM DIAGNOSTIC SYSTEM CHECK

    Click here

  9. CHECK SRS WARNING LIGHT

    Click here