REAR SEAT ASSEMBLY(for LH Side) REASSEMBLY

CAUTION / NOTICE / HINT

CAUTION:

Wear protective gloves. Sharp areas on the seatback frame, seat cushion frame and reclining adjuster may injure your hands.

PROCEDURE


  1. INSTALL REAR SEATBACK HEATER ASSEMBLY LH (w/ Seat Heater System)

    Click here

  2. INSTALL SEPARATE TYPE REAR SEATBACK COVER


    1. B0029IBC01
      *1 Hog Ring Pliers

      Set the separate type rear seatback cover in place.

    2. Using hog ring pliers, install the separate type rear seatback cover to the separate type rear seatback pad with 11 new hog rings.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

    3. B0029N7C01
      *1 Hog Ring Pliers

      Using hog ring pliers, install 5 new hog rings.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

  3. INSTALL SEPARATE TYPE REAR SEATBACK COVER WITH PAD


    1. B00299O

      Attach the 9 hooks to install the separate type rear seatback cover with pad to the rear seatback frame sub-assembly LH.

    2. B002A8O

      Attach the 8 claws to install the 4 rear seat headrest supports.

    3. B0029Y8

      Attach the 9 hooks.

  4. INSTALL REAR SEATBACK BOARD LH


    1. B0029K0

      Move the rear seatback board LH in the direction of the arrow to attach the guide.

    2. Attach the 7 claws to install the rear seatback board assembly LH.

    3. B00298O

      Close the 2 fasteners.

    4. B002A1DC01
      *1 Hog Ring Pliers

      Using hog ring pliers, install 6 new hog rings and attach the 2 pieces of fastener.

      Note


      • Be careful not to damage the separate type rear seatback cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seatback cover.

  5. INSTALL REAR NO. 1 SEATBACK ASSEMBLY LH


    1. B002A00

      Install the rear No. 1 seatback assembly LH to the rear seat reclining adjuster assembly LH with the 3 bolts.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  6. INSTALL REAR SEAT INNER BELT ASSEMBLY LH


    1. B0029R8

      Install the rear seat inner belt assembly LH with the bolt.

      Torque:
      42 N*m  { 428 kgf*cm, 31 ft.*lbf }

  7. INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY


    1. B002AFXC01
      *1 Cable Clamp A
      *2 Cable End
      *3 Clamp
      *4 Cable Clamp B

      Pass the No. 2 seat adjuster control cable assembly through the hole of the rear seat reclining adjuster assembly LH.

    2. Attach the cable clamp (A).

    3. Install the 2 clamps.

    4. Connect the 2 cable ends in the order shown in the illustration.

    5. Attach the 2 cable clamps (B).

  8. INSTALL REAR SEAT REAR CUSHION MOULDING LH


    1. B002A16C01
      *1 Clamp
      *2 Guide

      Attach the guide and claw to install the rear seat rear cushion moulding LH.

    2. w/ Seat Belt Warning System:

      Attach the 2 clamps to connect the wire harness.

  9. INSTALL REAR SEAT CUSHION MOULDING LH


    1. B002AK1

      Attach the 3 guides and claw to install the rear seat cushion moulding LH.

  10. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY RH (w/ Child Restraint System Guide)


    1. B00297P

      Attach the 2 claws to install the rear seatback hinge sub-assembly RH.

  11. INSTALL REAR SEATBACK HINGE SUB-ASSEMBLY LH (w/ Child Restraint System Guide)


    1. B0029O0

      Attach the 2 claws to install the rear seatback hinge sub-assembly LH.

  12. INSTALL REAR SEAT COVER


    1. B002AG0

      w/o Child Restraint System Guide:


      1. Attach the claw to install the rear seat cover.

      2. Install the clip and screw.

    2. B002AOM

      w/ Child Restraint System Guide:


      1. Attach the 4 claws to install the rear seat cover.

      2. Install the screw.

  13. INSTALL REAR SEATBACK COVER RH


    1. B0029JC

      w/o Child Restraint System Guide:


      1. Attach the claw to install the rear seatback cover RH.

      2. Install the clip and screw.

    2. B002AKA

      w/ Child Restraint System Guide:


      1. Attach the 4 claws to install the rear seatback cover RH.

      2. Install the screw.

  14. INSTALL REAR SEAT CUSHION FRAME SUB-ASSEMBLY LH


    1. B0029MJ

      Install the rear seat cushion frame sub-assembly LH with the 4 bushes and 4 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Connect the No. 2 seat adjuster control cable assembly to the rear seat cushion frame sub-assembly LH with the 2 clamps.

      B002A8PC01
      *1 Clamp *2 Cable End
      *3 Cable Clamp *4 No. 2 Seat Adjuster Control Cable Assembly
      *5 Separate Type Rear Seat Cushion Pad *6 Wire

      Note

      Pass the No. 2 seat adjuster control cable assembly between the separate type rear seat cushion pad and the wire of the rear seat cushion frame sub-assembly LH.

    3. Connect the cable end in the order shown in the illustration.

    4. Attach the cable clamp.

  15. INSTALL REAR SEATBACK COVER


    1. B002A2X

      Attach the 2 claws to install the rear seatback cover.

  16. INSTALL REAR SEAT CUSHION HEATER ASSEMBLY LH (w/ Seat Heater System)

    Click here

  17. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER


    1. B0029QXC01
      *1 Hog Ring Pliers

      Set the separate type rear seat cushion cover in place.

    2. Using hog ring pliers, install the separate type rear seat cushion cover to the rear seat cushion pad LH with 13 new hog rings.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

    3. B002A2LC01
      *1 Hog Ring Pliers

      Using hog ring pliers, install 2 new hog rings.

      Note


      • Be careful not to damage the separate type rear seat cushion cover.

      • Be sure to securely install the hog rings as shown in the illustration while preventing wrinkles from forming on the separate type rear seat cushion cover.

  18. INSTALL SEPARATE TYPE REAR SEAT CUSHION COVER WITH PAD


    1. B002AB9C01
      *1 Hog Ring Pliers

      Using hog ring pliers, install 3 new hog rings.

    2. Install the separate type seat cushion cover with pad to the rear seat cushion frame sub-assembly LH with the 22 hooks.

      B0029IE
    3. B0029IK

      w/ Seat Heater System:


      1. Connect the connector.

      2. Attach the 4 clamps to connect the wire harness.

  19. INSTALL REAR SEAT LOWER CUSHION HINGE COVER LH


    1. B002AKT

      Attach the guide and 4 claws to install the rear seat lower cushion hinge cover LH.

  20. INSTALL REAR SEAT NO. 3 CUSHION HINGE COVER


    1. B0029V5

      Attach the guide and 4 claws to install the rear seat No. 3 cushion hinge cover.

  21. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH


    1. B0029YW

      Install the reclining adjuster release handle LH with the 3 screws.

  22. INSTALL REAR SEATBACK NO. 1 BOARD CAP


    1. B0029QI

      Attach the 3 claws to install the rear seatback No. 1 board cap.

  23. INSTALL REAR SEAT NO. 1 CENTER ARMREST PLATE


    1. B00297E

      Install the rear seat No. 1 center armrest plate.

  24. INSTALL REAR SEAT CENTER ARMREST ASSEMBLY


    1. B0029RJ

      Install the rear seat center armrest assembly with the washer and bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  25. INSTALL CENTER ARMREST HINGE COVER RH


    1. B0029V0

      Attach the claw to install the center armrest hinge cover RH.

  26. INSTALL REAR CENTER SEAT LAP TYPE BELT ASSEMBLY LH

    Click here

  27. INSTALL REAR SEAT CENTER HEADREST ASSEMBLY


    1. Install the rear seat center headrest assembly.

  28. INSTALL REAR SEAT HEADREST ASSEMBLY


    1. Install the rear seat headrest assembly.