BLIND SPOT MONITOR SYSTEM DATA LIST / ACTIVE TEST


  1. DATA LIST

    Note

    In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

    Tech Tips

    Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.


    • *1: for LHD

    • *2: for RHD


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Data List.

    4. Read the Data List according to the display on the GTS.


      Body Electrical > Blind Spot Monitor Master > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Main Switch Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) / OFF or ON OFF or ON

      OFF: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) off

      ON: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on

      		 -
      Warning Indicator Turning on(Master) State of the outer rear view mirror indicator LH turning on OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met


      • Not during initial check

      • Vehicle detected in left hand side warning area

      • Left turn signal: off

      • Vehicle speed 40 km/h (25 mph) or more

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      		 -
      Warning Indicator Flashing(Master) State of the outer rear view mirror indicator LH flashing OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met


      • Not during initial check

      • Vehicle detected in left hand side warning area

      • Left turn signal: on

      • Vehicle speed 40 km/h (25 mph) or more

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      		 -
      Main Switch Indicator Status State of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) OFF or ON

      OFF: Indicator not illuminated

      ON: Indicator illuminated

      		 -
      Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V

      Not illuminated: 0 V

      Illuminated: 2.5 to 7.5 V

      		 -
      Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA

      Not illuminated: 0 mA

      Illuminated: 5 to 100 mA

      		 -
      Main Switch Indicator Input Circuit Voltage Blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly*1 or telltale light assembly*2) voltage Min.: 0 V, Max.: 25.5 V Always: 9 to 16 V -
      Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) Left ON, Right ON or OFF

      Left ON: Left side of turn signal light switch on

      Right ON: Right side of turn signal light switch on

      OFF: Turn signal light switch off

      		 -
      Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      		 -
      Vehicle Speed Vehicle speed signal Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      		 -
      Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
      Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      		 -
      HV Flag Hybrid vehicle OFF or ON

      OFF: Non-hybrid vehicle

      ON: Hybrid vehicle

      		 -
      VGRS Flag VGRS installed VGRS installed / OFF or ON

      OFF: VGRS not installed

      ON: VGRS installed

      		 -
      Main SW Inspection Completeness Flag Completion of inspection for blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) Incompl or Compl

      Incompl: Inspection not completed

      Compl: Inspection completed

      		 Changes to Compl when the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) is changed from off to on during Test Mode.
      Beam Axis Inspection Completeness Flag Completion of beam axis inspection Incompl or Compl

      Incompl: Inspection not completed

      Compl: Inspection completed

      		 Changes to Compl when Test Mode has been entered.
      Destination Undefined Flag Destination determination Unfixed or Fixed Fixed: Sensor destination information determined according to CAN destination information -
      Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
      Mirror LED Control Frequency This shows the frequency for the mirror LED control Min.: 1500 Hz, Max.: 2400 Hz Always: 1500 Hz -
      Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
      Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
      Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0%, Max.: 100% Always: 50 % -
      Main Switch LED Control Frequency Frequency of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when operating Min.: 100 Hz, Max.: 500 Hz Always: 100 Hz -
      Main Switch LED Duty Ratio (Bright Condition) Duty ratio of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when illuminated Min.: 0 %, Max.: 100 % 100 % -
      Main Switch LED Duty Ratio (Dimmed Condition) Duty ratio of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when dimmed Min.: 0 %, Max.: 100 % 30 % -
      Number of DTC Number of DTCs Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      		 -

      Body Electrical > Blind Spot Monitor Slave > Data List
      Tester Display Measurement Item Range Normal Condition Diagnostic Note
      Warning Indicator Turning on(Slave) State of the outer rear view mirror indicator RH turning on OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met


      • Not during initial check

      • Vehicle detected in right hand side warning area

      • Right turn signal: off

      • Vehicle speed 40 km/h (25 mph) or more

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      		 -
      Warning Indicator Flashing(Slave) State of the outer rear view mirror indicator RH flashing OFF or ON

      OFF: The following conditions are not met

      ON: All of the following conditions are met


      • Not during initial check

      • Vehicle detected in right hand side warning area

      • Vehicle speed 40 km/h (25 mph) or more

      • Right turn signal: on

      • Shift lever in any position except R

      • Blind spot monitor warning light not illuminated

      		 -
      Buzzer Sound Status State of the rear cross traffic alert buzzer (blind spot monitor buzzer) OFF or ON

      OFF: Buzzer not sounding

      ON: All of the following conditions are met:


      • Not during initial check

      • Vehicle detected in warning area of rear cross traffic alert

      • Speed difference between driver's vehicle and target vehicle is 1.5 m/s or more

      • Shift lever in R

      • No DTC output

      		 w/ RCTA
      Warning Indicator Input Circuit Voltage Outer rear view mirror indicator voltage Min.: 0 V, Max.: 25.5 V

      Not illuminated: 0 V

      Illuminated: 2.5 to 7.5 V

      		 -
      Warning Indicator Input Circuit Current Outer rear view mirror indicator current Min.: 0 mA, Max.: 255 mA

      Not illuminated: 0 mA

      Illuminated: 5 to 100 mA

      		 -
      Buzzer Input Circuit Voltage Rear cross traffic alert buzzer (blind spot monitor buzzer) voltage Min.: 0 V, Max.: 25.5 V Not sounding buzzer: 11 to 14 V Sounding buzzer: Alternating between 0 to 14 V w/ RCTA
      Turn Switch State State of the headlight dimmer switch assembly (turn signal light switch) Left ON, Right ON or OFF

      Left ON: Left side of turn signal light switch on

      Right ON: Right side of turn signal light switch on

      OFF: Turn signal light switch off

      		 -
      Reverse (Only for AT/CVT) State of the shift position R signal OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      		 -
      Reverse (Only for MT) State of the shift position R signal OFF or ON

      ON: Shift lever in R

      OFF: Shift lever in any position except R

      		 -
      Vehicle Speed Vehicle speed signal / Min.: 0 km/h (0 mph) Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) Vehicle stopped: 0 km/h (0 mph) -
      Steering Angle Steering angle sensor Min.: -3072°, Max.: 3070.5°

      Left turn: Increases

      Right turn: Decreases

      		 -
      Power Supply Voltage Power supply voltage Min.: 0 V, Max.: 50 V Always: 11 to 14 V -
      Indicator Light Control State Outer rear view mirror indicator dimming state Dim OFF or Dim ON

      Dim OFF: Indicator not dimmed

      Dim ON: Indicator dimmed

      		 -
      HV Flag Hybrid vehicle OFF or ON

      OFF: Non-hybrid vehicle

      ON: Hybrid vehicle

      		 -
      VGRS Flag VGRS installed OFF or ON

      OFF: VGRS not installed

      ON: VGRS installed

      		 -
      Beam Axis Inspection Completeness Flag Completion of beam axis inspection Incompl or Compl

      Incompl: Inspection not completed

      Compl: Inspection completed

      		 Changes to Compl when Test Mode has been entered.
      Destination Undefined Flag Destination determination Unfixed or Fixed Fixed: Sensor destination information determined according to CAN destination information -
      Angle Adjustment by Auto Alignment Angle adjusted using auto alignment Min.: Under -12.8 deg, Max.: Over 12.7 deg Angle adjusted using auto alignment is displayed When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed
      Mirror LED Control Frequency This shows the frequency for the mirror LED control Min.: 1500 Hz, Max.: 2400 Hz Always: 1500 Hz -
      Setting of Warning Indicator Current (Dim OFF) Set current of the outer rear view mirror indicator when not dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
      Setting of Warning Indicator Current (Dim ON) Set current of the outer rear view mirror indicator when dimmed Min.: 0 mA, Max.: 100 mA Always: 0 to 100 mA -
      Mirror LED Duty Ratio (Blinking) Duty ratio of the outer rear view mirror indicator when blinking Min.: 0%, Max.: 100% Always: 50 % -
      Number of DTC Number of DTCs Min.: 0, Max.: 255

      When system is normal: 0

      When a malfunction is detected: More than 0

      		 -