DATA LIST
Note
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
Tech Tips
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
*1: for LHD
*2: for RHD
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Data List.
Read the Data List according to the display on the GTS.
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Main Switch | Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) / OFF or ON | OFF or ON | OFF: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) off ON: Blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on |
- |
| Warning Indicator Turning on(Master) | State of the outer rear view mirror indicator LH turning on | OFF or ON | OFF: The following conditions are not met ON: All of the following conditions are met
|
- |
| Warning Indicator Flashing(Master) | State of the outer rear view mirror indicator LH flashing | OFF or ON | OFF: The following conditions are not met ON: All of the following conditions are met
|
- |
| Main Switch Indicator Status | State of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) | OFF or ON | OFF: Indicator not illuminated ON: Indicator illuminated |
- |
| Warning Indicator Input Circuit Voltage | Outer rear view mirror indicator voltage | Min.: 0 V, Max.: 25.5 V | Not illuminated: 0 V Illuminated: 2.5 to 7.5 V |
- |
| Warning Indicator Input Circuit Current | Outer rear view mirror indicator current | Min.: 0 mA, Max.: 255 mA | Not illuminated: 0 mA Illuminated: 5 to 100 mA |
- |
| Main Switch Indicator Input Circuit Voltage | Blind spot monitor indicator on the blind spot monitor main switch (warning canceling switch assembly*1 or telltale light assembly*2) voltage | Min.: 0 V, Max.: 25.5 V | Always: 9 to 16 V | - |
| Turn Switch State | State of the headlight dimmer switch assembly (turn signal light switch) | Left ON, Right ON or OFF | Left ON: Left side of turn signal light switch on Right ON: Right side of turn signal light switch on OFF: Turn signal light switch off |
- |
| Reverse (Only for AT/CVT) | State of the shift position R signal | OFF or ON | ON: Shift lever in R OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal | Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor | Min.: -3072°, Max.: 3070.5° | Left turn: Increases Right turn: Decreases |
- |
| Power Supply Voltage | Power supply voltage | Min.: 0 V, Max.: 50 V | Always: 11 to 14 V | - |
| Indicator Light Control State | Outer rear view mirror indicator dimming state | Dim OFF or Dim ON | Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed |
- |
| HV Flag | Hybrid vehicle | OFF or ON | OFF: Non-hybrid vehicle ON: Hybrid vehicle |
- |
| VGRS Flag | VGRS installed | VGRS installed / OFF or ON | OFF: VGRS not installed ON: VGRS installed |
- |
| Main SW Inspection Completeness Flag | Completion of inspection for blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) | Incompl or Compl | Incompl: Inspection not completed Compl: Inspection completed |
Changes to Compl when the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) is changed from off to on during Test Mode. |
| Beam Axis Inspection Completeness Flag | Completion of beam axis inspection | Incompl or Compl | Incompl: Inspection not completed Compl: Inspection completed |
Changes to Compl when Test Mode has been entered. |
| Destination Undefined Flag | Destination determination | Unfixed or Fixed | Fixed: Sensor destination information determined according to CAN destination information | - |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment | Min.: Under -12.8 deg, Max.: Over 12.7 deg | Angle adjusted using auto alignment is displayed | When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed |
| Mirror LED Control Frequency | This shows the frequency for the mirror LED control | Min.: 1500 Hz, Max.: 2400 Hz | Always: 1500 Hz | - |
| Setting of Warning Indicator Current (Dim OFF) | Set current of the outer rear view mirror indicator when not dimmed | Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Setting of Warning Indicator Current (Dim ON) | Set current of the outer rear view mirror indicator when dimmed | Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Mirror LED Duty Ratio (Blinking) | Duty ratio of the outer rear view mirror indicator when blinking | Min.: 0%, Max.: 100% | Always: 50 % | - |
| Main Switch LED Control Frequency | Frequency of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when operating | Min.: 100 Hz, Max.: 500 Hz | Always: 100 Hz | - |
| Main Switch LED Duty Ratio (Bright Condition) | Duty ratio of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when illuminated | Min.: 0 %, Max.: 100 % | 100 % | - |
| Main Switch LED Duty Ratio (Dimmed Condition) | Duty ratio of the blind spot monitor indicator on the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) when dimmed | Min.: 0 %, Max.: 100 % | 30 % | - |
| Number of DTC | Number of DTCs | Min.: 0, Max.: 255 | When system is normal: 0 When a malfunction is detected: More than 0 |
- |
| Tester Display | Measurement Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
| Warning Indicator Turning on(Slave) | State of the outer rear view mirror indicator RH turning on | OFF or ON | OFF: The following conditions are not met ON: All of the following conditions are met
|
- |
| Warning Indicator Flashing(Slave) | State of the outer rear view mirror indicator RH flashing | OFF or ON | OFF: The following conditions are not met ON: All of the following conditions are met
|
- |
| Warning Indicator Input Circuit Voltage | Outer rear view mirror indicator voltage | Min.: 0 V, Max.: 25.5 V | Not illuminated: 0 V Illuminated: 2.5 to 7.5 V |
- |
| Warning Indicator Input Circuit Current | Outer rear view mirror indicator current | Min.: 0 mA, Max.: 255 mA | Not illuminated: 0 mA Illuminated: 5 to 100 mA |
- |
| Turn Switch State | State of the headlight dimmer switch assembly (turn signal light switch) | Left ON, Right ON or OFF | Left ON: Left side of turn signal light switch on Right ON: Right side of turn signal light switch on OFF: Turn signal light switch off |
- |
| Reverse (Only for AT/CVT) | State of the shift position R signal | OFF or ON | ON: Shift lever in R OFF: Shift lever in any position except R |
- |
| Vehicle Speed | Vehicle speed signal / Min.: 0 km/h (0 mph) | Min.: 0 km/h (0 mph), Max.: 326 km/h (203 mph) | Vehicle stopped: 0 km/h (0 mph) | - |
| Steering Angle | Steering angle sensor | Min.: -3072°, Max.: 3070.5° | Left turn: Increases Right turn: Decreases |
- |
| Power Supply Voltage | Power supply voltage | Min.: 0 V, Max.: 50 V | Always: 11 to 14 V | - |
| Indicator Light Control State | Outer rear view mirror indicator dimming state | Dim OFF or Dim ON | Dim OFF: Indicator not dimmed Dim ON: Indicator dimmed |
- |
| HV Flag | Hybrid vehicle | OFF or ON | OFF: Non-hybrid vehicle ON: Hybrid vehicle |
- |
| VGRS Flag | VGRS installed | OFF or ON | OFF: VGRS not installed ON: VGRS installed |
- |
| Beam Axis Inspection Completeness Flag | Completion of beam axis inspection | Incompl or Compl | Incompl: Inspection not completed Compl: Inspection completed |
Changes to Compl when Test Mode has been entered. |
| Destination Undefined Flag | Destination determination | Unfixed or Fixed | Fixed: Sensor destination information determined according to CAN destination information | - |
| Angle Adjustment by Auto Alignment | Angle adjusted using auto alignment | Min.: Under -12.8 deg, Max.: Over 12.7 deg | Angle adjusted using auto alignment is displayed | When the adjusted angle is 12.7 degrees or more, "Over 12.7" is displayed and when it is -12.8 degrees or less, "Under -12.8" is displayed |
| Mirror LED Control Frequency | This shows the frequency for the mirror LED control | Min.: 1500 Hz, Max.: 2400 Hz | Always: 1500 Hz | - |
| Setting of Warning Indicator Current (Dim OFF) | Set current of the outer rear view mirror indicator when not dimmed | Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Setting of Warning Indicator Current (Dim ON) | Set current of the outer rear view mirror indicator when dimmed | Min.: 0 mA, Max.: 100 mA | Always: 0 to 100 mA | - |
| Mirror LED Duty Ratio (Blinking) | Duty ratio of the outer rear view mirror indicator when blinking | Min.: 0%, Max.: 100% | Always: 50 % | - |
| Number of DTC | Number of DTCs | Min.: 0, Max.: 255 | When system is normal: 0 When a malfunction is detected: More than 0 |
- |