BLIND SPOT MONITOR SYSTEM OPERATION CHECK

BLIND SPOT MONITOR BEAM AXIS INSPECTION

1. Procedure to enter Test Mode

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the ignition switch to ON.

   3. Turn the blind spot monitor main switch (warning cancel switch assembly*1 or telltale light assembly*2) on.

      
      

      • *1: for LHD

      • *2: for RHD

   4. Turn the GTS on.

   5. Switch the blind spot monitor sensor to Test Mode using the GTS. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis inspection or BSM Slave beam axis inspection.

   6. Finish Test Mode.

BLIND SPOT MONITOR BEAM AXIS CONFIRMATION

1. When performing the blind spot monitor beam axis confirmation, move the vehicle to a place where the space shown in the illustration can be secured.

   

   Note

   
   

   • Perform this inspection on level ground.

   • Make sure that there are no metal objects around the vehicle or on the ground.

   • Unload the vehicle before beginning the inspection.

   • Confirm that the tire pressure is correct before beginning the inspection.

   • Do not place an object other than the reflector (such as a large metallic object) in or allow people to enter the inspection area (W 9 m [29.53 ft.] x L 10 m [32.81 ft.] x H 4 m [13.13 ft.]) shown in the illustration.

   • Check that DTC C1ABB and DTC C1ABC are not output.

2. Place the reflector.

   
   

   1. Hang a string (with weight) from the center of the vehicle's rear emblem. Mark the vehicle's rear center point on the ground. Repeat for the front of the vehicle. (mark [A] and [B])

   2. 

      *1	Vehicle center line

      Draw a vehicle center line so that it passes through mark (A) and (B) (front and rear center points).

   3. 

      *1	501 to 521 mm (1.64 to 1.71 ft.)

      Mark the position on the center line 501 to 521 mm (1.64 to 1.71 ft.) behind the rear bumper. (Mark [C])

   4. 

      *1	Vehicle front
      *2	300 mm (11.8 in.)

      Prepare 2 pieces of string of 600 mm (1.97 ft.) in length and secure the end of each string at a point 300 mm (11.8 in.) from mark (C) as shown in the illustration.

   5. Pull the end of each string and mark the position where each string meets on both the left and right side (marks [D] and [E]).

      

      Vehicle rear

      *1	Vehicle center line
      *2	String

   6. 

      *1	Vehicle front
      *2	Vehicle center line
      *3	Line P

      Draw a line (P) so that it passes through mark (D) and (E) and is perpendicular to the vehicle center line.

   7. Set the reflector at the position (Z) shown in the illustration below.

      SST

      09870-60000 (09870-60010), 09870-60040

      

      Note

      
      

      • Set the reflector so that its center is 540 mm (1.77 ft.) above the ground.

      • 

        *1	Center of triangular pyramid

        The center of the triangular pyramid is the reference point for the setting position and angle.

      • Set the reflector as shown in the illustration so that the center of the triangular pyramid faces the blind spot monitor sensor.

      • Perform the operation as precisely as possible.

      

      *1	540 mm
      *2	(1.77 ft.)

3. Perform the blind spot monitor beam axis display.

   
   

   1. Connect the GTS to the DLC3.

   2. Turn the ignition switch to ON.

   3. Turn the blind spot monitor main switch (warning canceling switch assembly*1 or telltale light assembly*2) on.

      
      

      • *1: for LHD

      • *2: for RHD

   4. Turn the GTS on.

   5. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis display or BSM Slave beam axis display.

   6. Check the results displayed for the BSM beam axis display.

      Allowable Range

      Item	Blind Spot Monitor Sensor LH (Master)	Blind Spot Monitor Sensor RH (Slave)
      Angle	-3.6 to +3.6°	-3.6 to +3.6°
      Distance	2.0 to 3.0 m (6.57 to 9.85 ft.)	2.0 to 3.0 m (6.57 to 9.85 ft.)

      Tech Tips

      If the results are outside the allowable range, try again as the reflector setting position may be incorrect or a metal object may exist near the detection area.

   7. Perform the blind spot monitor beam axis adjustment using the GTS. Enter the following menus: Body Electrical / Blind spot monitor Master or Blind spot monitor Slave / Utility / BSM Master beam axis adjustment or BSM Slave beam axis adjustment.

      Tech Tips

      When values on the axis display are in the allowable range, performing this adjustment compensates the values to the normal value.

BLIND SPOT MONITOR INSTALLATION CONDITION INSPECTION