CAN COMMUNICATION SYSTEM(for RHD with Central Gateway ECU) TERMINALS OF ECU

Tech Tips

Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


  1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL


    1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

      Note


      • Before measuring the resistance, leave the vehicle for at least 1 minute and do not operate the ignition switch, any switches or any doors. If doors need to be opened in order to check connectors, open the doors and leave them open.

      • After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

        Click here

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

        Click here

  2. JUNCTION CONNECTOR


    1. No. 5 CAN Junction Connector (w/ Power Back Door System)

      A01QR8KC38
      *a

      Rear view of wire harness connector

      (to No. 5 CAN Junction Connector)

      		 *b for Main Body ECU (Multiplex Network Body ECU)
      *c for Multiplex Network Door ECU *d for No. 1 CAN Junction Terminal
      No. 5 CAN Junction Connector Wiring Color Connect to
      N32-7 (CANH) B Main body ECU (multiplex network body ECU)
      N32-18 (CANL) GR
      N32-8 (CANH) G Multiplex network door ECU
      N32-19 (CANL) GR
      N32-9 (CANH) L No. 1 CAN junction terminal
      N32-20 (CANL) GR

    2. No. 6 CAN Junction Connector

      A01QR8KC42
      *a

      Rear view of wire harness connector

      (to No. 6 CAN Junction Connector)

      		 *b for Main Body ECU (Multiplex Network Body ECU)
      *c for Air Conditioning Amplifier Assembly *d for Brake Actuator Assembly (Skid Control ECU)
      *e for No. 7 CAN Junction Connector *f for Engine Stop and Start ECU (w/ Stop and Start System)
      *g for Airbag Sensor Assembly *h for ECM
      No. 6 CAN Junction Connector Wiring Color Connect to
      G188-1 (CANH) G Main body ECU (multiplex network body ECU)
      G188-12 (CANL) W
      G188-2 (CANH) B Air conditioning amplifier assembly
      G188-13 (CANL) W
      G188-3 (CANH) GR Brake actuator assembly (skid control ECU)
      G188-14 (CANL) W
      G188-4 (CANH) V No. 7 CAN junction connector
      G188-15 (CANL) W
      G188-5 (CANH) LG Engine stop and start ECU*
      G188-16 (CANL) W
      G188-6 (CANH) BR Airbag sensor assembly
      G188-17 (CANL) W
      G188-7 (CANH) Y ECM
      G188-18 (CANL) W

      *: w/ Stop and Start System

    3. No. 7 CAN Junction Connector

      A01QR8KC76
      *a

      Rear view of wire harness connector

      (to No. 7 CAN Junction Connector)

      		 *b for Combination Meter Assembly
      *c for Power Steering ECU Assembly *d for Spiral with Sensor Cable Sub-assembly (Steering Angle Sensor)
      *e for Certification ECU (Smart Key ECU Assembly) (w/ Entry and Start System) *f for 4WD ECU Assembly (for 4WD/AWD)
      *g for No. 6 CAN Junction Connector *h for Central Gateway ECU
      No. 7 CAN Junction Connector Wiring Color Connect to
      G189-1 (CANH) G Combination meter assembly
      G189-12 (CANL) W
      G189-2 (CANH) LG Power steering ECU assembly
      G189-13 (CANL) W
      G189-4 (CANH) BE Spiral with sensor cable sub-assembly (steering angle sensor)
      G189-15 (CANL) W
      G189-5 (CANH) R Certification ECU (smart key ECU assembly)*1
      G189-16 (CANL) W
      G189-6 (CANH) GR 4WD ECU assembly*2
      G189-17 (CANL) W
      G189-8 (CANH) V No. 6 CAN junction connector
      G189-19 (CANL) W
      G189-10 (CANH) SB Central gateway ECU
      G189-21 (CANL) W

      *1: w/ Entry and Start System

      *2: for 4WD/AWD

    4. No. 8 CAN Junction Connector

      A01QR8KC44
      *a

      Rear view of wire harness connector

      (to No. 8 CAN Junction Connector)

      		 *b

      • for Navigation Receiver Assembly (w/ Navigation System)

      • for Radio and Display Receiver Assembly (w/ Audio and Visual System [for Radio and Display Type])
      *c for Central Gateway ECU *d for Driving Support ECU Assembly (w/ Pre-crash Safety System)
      *e for Forward Recognition Camera (w/ Pre-crash Safety System) *f for Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System)
      No. 8 CAN Junction Connector Wiring Color Connect to
      G173-1 (CANH) Y

      • Navigation receiver assembly*1

      • Radio and display receiver assembly*2
      G173-12 (CANL) W
      G173-3 (CANH) R Central gateway ECU
      G173-14 (CANL) W
      G173-4 (CANH) V Central gateway ECU
      G173-15 (CANL) W
      G173-5 (CANH) B Driving support ECU assembly*3
      G173-16 (CANL) W
      G173-6 (CANH) L Forward recognition camera*3
      G173-17 (CANL) W
      G173-7 (CANH) SB Millimeter wave radar sensor assembly*3
      G173-18 (CANL) W

      *1: w/ Navigation System

      *2: w/ Audio and Visual System (for Radio and Display Type)

      *3: w/ Pre-crash Safety System

    5. No. 9 CAN Junction Connector

      A01QT4JC15
      *a

      Front view of wire harness connector

      (to No. 9 CAN Junction Connector)

      		 *b for Forward Recognition Camera (w/ Pre-crash Safety System)
      *c for Millimeter Wave Radar Sensor Assembly (w/ Pre-crash Safety System) *d for Driving Support ECU Assembly (w/ Pre-crash Safety System)
      *e for Central Gateway ECU *f for No. 10 CAN Junction Connector
      *g for Clearance Warning ECU Assembly (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type]) - -
      No. 9 CAN Junction Connector Wiring Color Connect to
      G174-1 (CANH) G Forward recognition camera*1
      G174-11 (CANL) LG
      G174-2 (CANH) B Millimeter wave radar sensor assembly*1
      G174-12 (CANL) LG
      G174-3 (CANH) P Driving support ECU assembly*1
      G174-13 (CANL) LG
      G174-4 (CANH) Y Central gateway ECU
      G174-14 (CANL) LG
      G174-5 (CANH) L No. 10 CAN junction connector
      G174-15 (CANL) LG
      G174-6 (CANH) R Clearance warning ECU assembly*2
      G174-16 (CANL) LG

      *1: w/ Pre-crash Safety System

      *2: w/ TOYOTA Parking Assist-sensor System (for 8 Sensor Type)

    6. No. 10 CAN Junction Connector

      A01QT4JC35
      *a

      Front view of wire harness connector

      (to No. 10 CAN Junction Connector)

      		 *b for Central Gateway ECU
      *c for No. 9 CAN Junction Connector *d for Blind Spot Monitor Sensor LH (w/ Blind Spot Monitor System)
      *e for Television Camera Assembly (w/ Parking Assist Monitor System [for Camera built-in ECU]) - -
      No. 10 CAN Junction Connector Wiring Color Connect to
      N36-2 (CANH) V Central gateway ECU
      N36-12 (CANL) LG
      N36-3 (CANH) L No. 9 CAN junction connector
      N36-13 (CANL) LG
      N36-4 (CANH) R Blind spot monitor sensor LH*1
      N36-14 (CANL) LG
      N36-5 (CANH) P Television camera assembly*2
      N36-15 (CANL) LG

      *1: w/ Blind Spot Monitor System

      *2: w/ Parking Assist Monitor System (for Camera built-in ECU)

    7. A01QQHDC41
      *a

      Rear view of wire harness connector

      (to No. 1 CAN Junction Terminal)
      *b for No. 5 CAN Junction Connector

      No. 1 CAN Junction Terminal (w/ Power Back Door System)

      No. 1 CAN Junction Terminal Wiring Color Connect to
      N31-2 (CANL) GR No. 5 CAN junction connector
      N31-3 (CANH) L

  3. CHECK DLC3


    1. A01QQYTC06
      *a Front view of DLC3

      Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

      CAUTION:

      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the airbag system.

      Note


      • After turning the cable disconnected from negative (-) battery terminal, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

        Click here

      • When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

        Click here

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G14-6 (CANH) - G14-14 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 66 Ω
      G14-6 (CANH) - G14-4 (CG) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G14-14 (CANL) - G14-4 (CG) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G14-6 (CANH) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G14-14 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  4. CHECK CENTRAL GATEWAY ECU


    1. A01QR7EC06
      *A Bus 2
      *B Bus 3
      *C Bus 5
      *D V Bus
      *a

      Front view of wire harness connector

      (to Central Gateway ECU)

      Disconnect the central gateway ECU connector.

    2. Measure the resistance according to the value(s) in the table below.

      Bus 2
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G170-18 (CA4H) - G170-17 (CA4L) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G170-18 (CA4H) - G170-10 (GND) SB - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-17 (CA4L) - G170-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-18 (CA4H) - G170-1 (BATT) SB - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G170-17 (CA4L) - G170-1 (BATT) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Bus 3
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G170-6 (CA3H) - G170-21 (CA3L) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-6 (CA3H) - G170-10 (GND) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-21 (CA3L) - G170-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-6 (CA3H) - G170-1 (BATT) R - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G170-21 (CA3L) - G170-1 (BATT) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Bus 3
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G170-19 (CAYH) - G170-20 (CAYL) V - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-19 (CAYH) - G170-10 (GND) V - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-20 (CAYL) - G170-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-19 (CAYH) - G170-1 (BATT) V - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G170-20 (CAYL) - G170-1 (BATT) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Bus 5
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G170-15 (CA5H) - G170-16 (CA5L) Y - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-15 (CA5H) - G170-10 (GND) Y - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-16 (CA5L) - G170-10 (GND) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-15 (CA5H) - G170-1 (BATT) Y - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G170-16 (CA5L) - G170-1 (BATT) LG - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Bus 5
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G170-9 (CAXH) - G170-24 (CAXL) V - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-9 (CAXH) - G170-10 (GND) V - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-24 (CAXL) - G170-10 (GND) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-9 (CAXH) - G170-1 (BATT) V - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G170-24 (CAXL) - G170-1 (BATT) LG - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      V Bus
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G170-14 (CA6H) - G170-10 (GND) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-5 (CA6L) - G170-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G170-14 (CA6H) - G170-1 (BATT) B - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G170-5 (CA6L) - G170-1 (BATT) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  5. CHECK ECM


    1. for 2AR-FE:

      A01QPJ0E02

      1. Disconnect the ECM connectors.

        A01QQD4C05
        *a

        Front view of wire harness connector

        (to ECM)

        		 - -

      2. Measure the resistance according to the value(s) in the table below.

        Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
        A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
        A62-13 (CANH) - B77-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-26 (CANL) - B77-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

    2. for 3ZR-FAE, 3ZR-FE:

      A01QPJ0C19
      *A for 3ZR-FAE *B for 3ZR-FE, Manual Transaxle System
      *C for 3ZR-FE, CVT (K114) *D for 3ZR-FE, CVT (K111)

      1. Disconnect the ECM connectors.

        A01QQD4C52
        *A for 3ZR-FAE *B for 3ZR-FE, Manual Transaxle System
        *C for 3ZR-FE, CVT (K114) *D for 3ZR-FE, CVT (K111)
        *a

        Front view of wire harness connector

        (to ECM)

        		 - -

      2. Measure the resistance according to the value(s) in the table below.

        for 3ZR-FAE
        Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
        A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
        A62-13 (CANH) - B93-59 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-26 (CANL) - B93-59 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        for 3ZR-FE, Manual Transaxle System
        Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
        A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
        A62-13 (CANH) - B93-59 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-26 (CANL) - B93-59 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        for 3ZR-FE, CVT (K114)
        Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
        A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
        A62-13 (CANH) - B93-59 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-26 (CANL) - B93-59 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        for 3ZR-FE, CVT (K111)
        Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
        A62-13 (CANH) - A62-26 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
        A62-13 (CANH) - B75-16 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-26 (CANL) - B75-16 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-13 (CANH) - A62-1 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        A62-26 (CANL) - A62-1 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

    3. for 2WW:

      A01QPJ0C18

      1. A01QR58C23
        *a

        Front view of wire harness connector

        (to ECM)

        Disconnect the ECM connector.

      2. Measure the resistance according to the value(s) in the table below.

        Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
        A62-26 (CANH) - A62-25 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
        A62-26 (CANH) - A62-4 (E1) Y - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-25 (CANL) - A62-4 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A62-26 (CANH) - A62-15 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        A62-25 (CANL) - A62-15 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

    4. for 2AD-FTV, 2AD-FHV, 2AD-CCo, 2AD-DPF:

      A01QPIRE30

      1. Disconnect the ECM connectors.

        A01QQRSC12
        *a

        Front view of wire harness connector

        (to ECM)

        		 - -

      2. Measure the resistance according to the value(s) in the table below.

        Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
        A61-7 (CANH) - A61-6 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
        A61-7 (CANH) - B76-109 (E1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A61-6 (CANL) - B76-109 (E1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
        A61-7 (CANH) - A61-2 (BATT) Y - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
        A61-6 (CANL) - A61-2 (BATT) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  6. CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) AND INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY

    A01QRX2C01
    *A Main Body ECU (Multiplex Network Body ECU) with 1 Connector *B Main Body ECU (Multiplex Network Body ECU) with 3 Connectors
    *C Bus 2 *D Sub Bus 1
    *1 Main Body ECU (Multiplex Network Body ECU) - -

    1. Remove the main body ECU (multiplex network body ECU).

      Click here

      A01QQFNC01
      *A Bus 2 *B Sub Bus 1
      *a

      Rear view of wire harness connector

      (to Main Body ECU [Multiplex Network Body ECU])

      		 *b

      Front view of wire harness connector

      (to Main Body ECU [Multiplex Network Body ECU])

    2. Reconnect the instrument panel junction block assembly connectors.

    3. Measure the resistance according to the value(s) in the table below.

      Bus 2
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G78-14 (CANH) - G78-13 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G78-14 (CANH) - A-11 (GND1) G - None HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G78-13 (CANL) - A-11 (GND1) W - None LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G78-14 (CANH) - A-30 (BECU) G - None HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G78-13 (CANL) - A-30 (BECU) W - None LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Sub Bus 1
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G79-9 (CANP) - G79-10 (CANN) B - GR HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      G79-9 (CANP) - A-11 (GND1) B - None HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G79-10 (CANN) - A-11 (GND1) GR - None LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G79-9 (CANP) - A-30 (BECU) B - None HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G79-10 (CANN) - A-30 (BECU) GR - None LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  7. CHECK COMBINATION METER ASSEMBLY

    A01QQH2E26

    1. A01QQ35C07
      *a

      Rear view of wire harness connector

      (to Combination Meter Assembly)

      Disconnect the combination meter assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G16-32 (CANH) - G16-31 (CANL) G - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      G16-32 (CANH) - G16-21 (ET) G - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G16-31 (CANL) - G16-21 (ET) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G16-32 (CANH) - G16-40 (B) G - Y HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G16-31 (CANL) - G16-40 (B) W - Y LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  8. CHECK AIRBAG SENSOR ASSEMBLY

    A01QQOWE89

    1. A01QSIJC03
      *a

      Rear view of wire harness connector

      (to Airbag Sensor Assembly)
      *b Front view of DLC3

      Disconnect the airbag sensor assembly connector.

      Click here

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G92-13 (CANH) - G92-22 (CANL) BR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G92-13 (CANH) - G92-25 (E1) BR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G92-22 (CANL) - G92-25 (E1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G92-13 (CANH) - G14-16 (BAT) BR - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G92-22 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  9. CHECK BRAKE ACTUATOR ASSEMBLY (SKID CONTROL ECU)

    A01QP9HE06

    1. A01QTS4C27
      *a

      Front view of wire harness connector

      (to Brake Actuator Assembly [Skid Control ECU])

      Disconnect the brake actuator assembly (skid control ECU) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      A80-22 (CANH) - A80-10 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      A80-22 (CANH) - A80-1 (GND1) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      A80-10 (CANL) - A80-1 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      A80-22 (CANH) - A80-13 (BM) B - B HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      A80-10 (CANL) - A80-13 (BM) W - B LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  10. CHECK SPIRAL WITH SENSOR CABLE SUB-ASSEMBLY (STEERING ANGLE SENSOR)

    A01QQIPE03

    1. A01QQXLC04
      *a

      Front view of wire harness connector

      (to Spiral with Sensor Cable Sub-assembly [Steering Angle Sensor])

      Disconnect the spiral with sensor cable sub-assembly (steering angle sensor) connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G12-3 (CANH) - G12-2 (CANL) BE - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G12-3 (CANH) - G12-1 (ESS) BE - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G12-2 (CANL) - G12-1 (ESS) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G12-3 (CANH) - G12-5 (BAT) BE - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G12-2 (CANL) - G12-5 (BAT) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  11. CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (w/ Entry and Start System)

    A01QQRME76

    1. A01QQWGC02
      *a

      Front view of wire harness connector

      (to Certification ECU [Smart Key ECU Assembly])

      Disconnect the certification ECU (smart key ECU assembly) connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G84-14 (CANH) - G84-15 (CANL) R - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G84-14 (CANH) - G82-11 (E) R - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G84-15 (CANL) - G82-11 (E) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G84-14 (CANH) - G82-2 (+B) R - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G84-15 (CANL) - G82-2 (+B) W - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  12. CHECK RADIO AND DISPLAY RECEIVER ASSEMBLY (w/ Audio and Visual System [for Radio and Display Type])

    A01QTBQE01

    1. A01QSYRC07
      *a

      Front view of wire harness connector

      (to Radio and Display Receiver Assembly)

      Disconnect the radio and display receiver assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G143-9 (CANH) - G143-10 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G143-9 (CANH) - G141-7 (GND1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G143-10 (CANL) - G141-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G143-9 (CANH) - G141-4 (+B1) Y - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G143-10 (CANL) - G141-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  13. CHECK NAVIGATION RECEIVER ASSEMBLY (w/ Navigation System)

    A01QTBQE08

    1. A01QSYRC27
      *a

      Front view of wire harness connector

      (to Navigation Receiver Assembly)

      Disconnect the navigation receiver assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G139-9 (CANH) - G139-10 (CANL) Y - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G139-9 (CANH) - G137-7 (GND1) Y - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G139-10 (CANL) - G137-7 (GND1) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G139-9 (CANH) - G137-4 (+B1) Y - SB HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G139-10 (CANL) - G137-4 (+B1) W - SB LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  14. CHECK 4WD ECU ASSEMBLY (for 4WD/AWD)

    A01QSP4E03

    1. A01QT9TC05
      *a

      Rear view of wire harness connector

      (to 4WD ECU Assembly)
      *b Front view of DLC3

      Disconnect the 4WD ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G86-6 (CANH) - G86-5 (CANL) GR - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G86-6 (CANH) - G86-4 (GND) GR - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G86-5 (CANL) - G86-4 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G86-6 (CANH) - G14-16 (BAT) GR - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G86-5 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  15. CHECK ENGINE STOP AND START ECU (w/ Stop and Start System)

    A01QT0VE02

    1. A01QR94C02
      *a

      Front view of wire harness connector

      (to Engine Stop and Start ECU)

      Disconnect the engine stop and start ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G87-13 (CANH) - G87-14 (CANL) LG - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G87-13 (CANH) - A86-8 (GND1) LG - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G87-14 (CANL) - A86-8 (GND1) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G87-13 (CANH) - A86-3 (BIN1) LG - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G87-14 (CANL) - A86-3 (BIN1) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  16. CHECK AIR CONDITIONING AMPLIFIER ASSEMBLY

    A01QRABE01

    1. A01QQ35C06
      *a

      Rear view of wire harness connector

      (to Air Conditioning Amplifier Assembly)

      Disconnect the air conditioning amplifier assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G81-11 (CANH) - G81-12 (CANL) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G81-11 (CANH) - G81-14 (GND) B - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G81-12 (CANL) - G81-14 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G81-11 (CANH) - G81-21 (B) B - GR HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G81-12 (CANL) - G81-21 (B) W - GR LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  17. CHECK POWER STEERING ECU ASSEMBLY

    A01QSPAE06

    1. A01QQ20C01
      *a

      Front view of wire harness connector

      (to Power Steering ECU Assembly)

      Disconnect the power steering ECU assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      h1-4 (CANH) - h1-8 (CANL) W - B HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      h1-4 (CANH) - h2-2 (PGND) W - B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      h1-8 (CANL) - h2-2 (PGND) B - B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      h1-4 (CANH) - h2-1 (PIG) W - R HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      h1-8 (CANL) - h2-1 (PIG) B - R LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  18. CHECK BLIND SPOT MONITOR SENSOR LH (w/ Blind Spot Monitor System)

    A01QQ83E10

    1. A01QRRAC15
      *a

      Front view of wire harness connector

      (to Blind Spot Monitor Sensor LH)
      *b Front view of DLC3

      Disconnect the blind spot monitor sensor LH connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      R1-2 (CA1P) - R1-7 (CA1N) R - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      R1-2 (CA1P) - R1-10 (BLGD) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      R1-7 (CA1N) - R1-10 (BLGD) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      R1-2 (CA1P) - G14-16 (BAT) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      R1-7 (CA1N) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  19. CHECK MULTIPLEX NETWORK DOOR ECU (w/ Power Back Door System)

    A01QTU8E08

    1. A01QQK0C19
      *a

      Front view of wire harness connector

      (to Multiplex Network Door ECU)

      Disconnect the multiplex network door ECU connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      U29-39 (CANP) - U29-40 (CANN) G - GR HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      U29-39 (CANP) - U30-10 (GND) G - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      U29-40 (CANN) - U30-10 (GND) GR - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      U29-39 (CANP) - U30-1 (B) G - W HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      U29-40 (CANN) - U30-1 (B) GR - W LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  20. CHECK CLEARANCE WARNING ECU ASSEMBLY (w/ TOYOTA Parking Assist-sensor System [for 8 Sensor Type])

    A01QP34E06

    1. A01QOJWC12
      *a

      Rear view of wire harness connector

      (to Clearance Warning ECU Assembly)
      *b Front view of DLC3

      Disconnect the clearance warning ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G166-17 (R1) - G166-18 (R2) R - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G166-17 (R1) - G166-30 (E) R - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G166-18 (R2) - G166-30 (E) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G166-17 (R1) - G14-16 (BAT) R - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G166-18 (R2) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  21. CHECK FORWARD RECOGNITION CAMERA (w/ Pre-crash Safety System)

    A01QSETC02
    *A Bus 5
    *B Local Bus

    1. A01QPB1C14
      *A Bus 5
      *B Local Bus
      *a

      Front view of wire harness connector

      (to Forward Recognition Camera)
      *b Front view of DLC3

      Disconnect the forward recognition camera connector.

    2. Measure the resistance according to the value(s) in the table below.

      Bus 5
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      Q17-5 (CA1P) - Q17-11 (CA1N) G - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Q17-5 (CA1P) - Q17-10 (GND) G - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Q17-11 (CA1N) - Q17-10 (GND) LG - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Q17-5 (CA1P) - G14-16 (BAT) G - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Q17-11 (CA1N) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Local Bus
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      Q17-6 (CANH) - Q17-12 (CANL) L - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Q17-6 (CANH) - Q17-10 (GND) L - W-B HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Q17-12 (CANL) - Q17-10 (GND) W - W-B LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Q17-6 (CANH) - G14-16 (BAT) L - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Q17-12 (CANL) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  22. CHECK DRIVING SUPPORT ECU ASSEMBLY (w/ Pre-crash Safety System)


    1. A01QQFLC02
      *A Bus 5
      *B Local Bus
      *a

      Front view of wire harness connector

      (to Driving Support ECU Assembly)
      *b Front view of DLC3

      Disconnect the driving support ECU assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Bus 5
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G168-10 (CA2H) - G168-11 (CA2L) P - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G168-10 (CA2H) - G168-28 (GND) P - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G168-11 (CA2L) - G168-28 (GND) LG - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G168-10 (CA2H) - G14-16 (BAT) P - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G168-11 (CA2L) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Local Bus
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      G168-8 (CA1P) - G168-9 (CA1N) B - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      G168-8 (CA1P) - G168-28 (GND) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G168-9 (CA1N) - G168-28 (GND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      G168-8 (CA1P) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      G168-9 (CA1N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  23. CHECK MILLIMETER WAVE RADAR SENSOR ASSEMBLY (w/ Pre-crash Safety System)


    1. A01QSD3C03
      *A Bus 5
      *B Local Bus
      *a

      Front view of wire harness connector

      (to Millimeter Wave Radar Sensor Assembly)
      *b Front view of DLC3

      Disconnect the millimeter wave radar sensor assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Bus 5
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      Z6-3 (CA2H) - Z6-2 (CA2L) B - LG HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      Z6-3 (CA2H) - Z6-1 (SGND) B - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Z6-2 (CA2L) - Z6-1 (SGND) LG - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Z6-3 (CA2H) - G14-16 (BAT) B - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Z6-2 (CA2L) - G14-16 (BAT) LG - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Local Bus
      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      Z6-5 (CA1P) - Z6-6 (CA1N) SB - W HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 108 to 132 Ω
      Z6-5 (CA1P) - Z6-1 (SGND) SB - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Z6-6 (CA1N) - Z6-1 (SGND) W - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      Z6-5 (CA1P) - G14-16 (BAT) SB - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      Z6-6 (CA1N) - G14-16 (BAT) W - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher

  24. CHECK TELEVISION CAMERA ASSEMBLY (w/ Parking Assist Monitor System [for Camera built-in ECU])

    A01QTHZE22

    1. A01QOWVC04
      *a

      Front view of wire harness connector

      (to Television Camera Assembly)
      *b Front view of DLC3

      Disconnect the television camera assembly connector.

    2. Measure the resistance according to the value(s) in the table below.

      Terminal No. (Symbol) Wiring Color Terminal Description Condition Specified Condition
      c2-4 (CANH) - c2-1 (CANL) P - G HIGH-level CAN bus wire - LOW-level CAN bus wire Cable disconnected from negative (-) battery terminal 54 to 69 Ω
      c2-4 (CANH) - G14-4 (CG) P - BR HIGH-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      c2-1 (CANL) - G14-4 (CG) G - BR LOW-level CAN bus wire - GND Cable disconnected from negative (-) battery terminal 200 Ω or higher
      c2-4 (CANH) - G14-16 (BAT) P - L HIGH-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher
      c2-1 (CANL) - G14-16 (BAT) G - L LOW-level CAN bus wire - Battery positive (+) Cable disconnected from negative (-) battery terminal 6 kΩ or higher