NAVIGATION SYSTEM(for Radio and Display Type), Diagnostic DTC:B15D3

DTC Code DTC Name
B15D3 Stereo Component Amplifier Disconnected

DESCRIPTION

The radio and display receiver assembly and stereo component amplifier assembly are connected via AVC-LAN communication.

When an AVC-LAN communication error occurs between the radio and display receiver assembly and stereo component amplifier assembly, this DTC will be stored.

DTC No. Detection Item DTC Detection Condition Trouble Area
B15D3 Stereo Component Amplifier Disconnected

When either condition below is met:


  • Stereo component amplifier assembly is/was not connected while the ignition switch is ON or ACC.

  • Communication between the master unit and the stereo component amplifier assembly is not possible when the engine is started.

  • Stereo component amplifier assembly

  • Radio and display receiver assembly

  • Harness or connector

Tech Tips


  • Even if no fault is present, this DTC may be stored depending on the battery condition.

  • The radio and display receiver assembly is the master unit.

WIRING DIAGRAM

A01QU3EE06

CAUTION / NOTICE / HINT

Note


  • Inspect the fuses for circuits related to this system before performing the following inspection procedure.

  • Check that the wire harness is properly installed and does not have any sharp bends, pinching or loose connections.

    Click here

PROCEDURE


  1. CHECK FOR


    1. If DTC B15C3 is output, perform troubleshooting for DTC B15C3 first.

      Result
      Result Proceed to
      DTC B15C3 is not output A
      DTC B15C3 is output B

    B

    GO TO DTC "B15C3" IN DIAGNOSTIC TROUBLE CODE CHART Click here

    A

  2. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result
      Result Proceed to
      Optional components (including associated wiring) are installed. A
      Optional components (including associated wiring) are not installed. B

      Tech Tips


      • Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.

      • This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.


    B

    GO TO STEP 4 Click here

    A

  3. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)


    1. Remove optional components (including associated wiring).

      Note

      Do not remove optional components or associated wiring without the permission of the customer.

      Result
      Proceed to
      NEXT

    NEXT

  4. CHECK FOR DTC


    1. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    2. Recheck for DTCs and check if the same DTC is output again.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (COMMUNICATION MALFUNCTION DUE TO NOISE)

    NG

  5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)


    1. A01QTIGC01
      *a

      Front view of wire harness connector

      (to Stereo Component Amplifier Assembly)

      Disconnect the stereo component amplifier assembly connectors.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      M33-3 (GND) - Body ground Always Below 1 Ω

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      M33-1 (+B) - M33-3 (GND) Always 11 to 14 V
      M32-12 (ACC) - M33-3 (GND) Ignition switch ACC 11 to 14 V
      Ignition switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  6. CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)


    1. Disconnect the G143 radio and display receiver assembly connector.

    2. Disconnect the M32 stereo component amplifier assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G143-7 (TX1+) - M32-8 (TX+) Always Below 1 Ω
      G143-8 (TX1-) - M32-7 (TX-) Always Below 1 Ω
      G143-7 (TX1+) - Body ground Always 10 kΩ or higher
      G143-8 (TX1-) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  7. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY


    1. Replace the stereo component amplifier assembly with a known good one.

      Click here

    2. Clear the DTCs.

      Click here


      Body Electrical > Navigation System > Clear DTCs

    3. Recheck for DTCs and check if the same DTC is output again.

      Click here


      Body Electrical > Navigation System > Trouble Codes
      OK
      No DTCs are output.
      Result
      Proceed to
      OK
      NG

    OK

    END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

    NG

    REPLACE RADIO & DISPLAY RECEIVER ASSEMBLY Click here