AUDIO AND VISUAL SYSTEM(for Radio and Display Type)

CHECK DTC (CHECK USING GTS)

Connect the GTS to the DLC3.
Engine start.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Trouble Codes.
Check for DTCs, and then write them down.

Body Electrical > Navigation System > Trouble Codes
Check the details of the DTC(s).

Click here

CLEAR DTC (CLEAR USING GTS)

Connect the GTS to the DLC3.
Engine start.
Turn the GTS on.
Enter the following menus: Body Electrical / Navigation System / Trouble Codes / Clear DTCs.
Clear the DTCs.

Body Electrical > Navigation System > Clear DTCs

START DIAGNOSTIC MODE (for 6.1 Inch Display)

Tech Tips

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
After the ignition switch is turned to ON, check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.
Start diagnostic mode using either of the 2 methods below.

Method 1
1. *a "MEDIA" Switch
  
  *b "CAR" Switch
  
  Start the engine.
2. While pressing and holding the "CAR" or "MEDIA" switch of the radio and display receiver assembly, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.
3. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.
Method 2

Note

If the operation fails and diagnostic mode cannot be entered, turn the radio and display receiver assembly screen display on and off once, and then perform the procedures listed below from the first step again. (Only turning the radio and display receiver assembly power supply on and off will not work.)
1. *a ">" Switch
  
  *b "<" Switch
  
  Start the engine.
2. Turn the radio and display receiver assembly screen display off.
3. Turn the radio and display receiver assembly power supply off.
4. Press the ">" switch 5 times, and then press the "<" switch 5 times within 15 seconds.
5. Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

START DIAGNOSTIC MODE (for 7 Inch Display)

Tech Tips

Illustrations may differ from the actual vehicle screen depending on the device settings and options. Therefore, some detailed areas may not be shown exactly the same as on the actual vehicle screen.
After the ignition switch is turned to ON, check that the map is displayed before starting diagnostic mode. Otherwise, some items cannot be checked.
Start diagnostic mode using either of the 2 methods below.

Method 1

*A	for LHD
*B	for RHD
*a	"MEDIA" Switch
*b	"CAR" Switch

Start the engine.

While pressing and holding the "CAR" or "MEDIA" switch of the radio and display receiver assembly, operate the light control switch: Off → Tail → Off → Tail → Off → Tail → Off.
Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

Method 2

Note

If the operation fails and diagnostic mode cannot be entered, turn the radio and display receiver assembly screen display on and off once, and then perform the procedures listed below from the first step again. (Only turning the radio and display receiver assembly power supply on and off will not work.)

*A	for LHD
*B	for RHD
*a	">" Switch
*b	"<" Switch

Start the engine.

Turn the radio and display receiver assembly screen display off.
Turn the radio and display receiver assembly power supply off.
Press the ">" switch 5 times, and then press the "<" switch 5 times within 15 seconds.
Diagnostic mode starts and the "Service Menu" screen will be displayed. Service inspection starts automatically and the result will be displayed.

FAILURE DIAGNOSIS

Press the "Failure Diagnosis" switch on the "Service Menu" screen.
The "Failure Diagnosis" will be displayed.

SYSTEM CHECK

Press the "System Check" switch on the "Failure Diagnosis" screen.
The "System Check Mode" screen will be displayed.

CHECK DTC (CHECK USING SYSTEM CHECK MODE SCREEN)

System check mode screen description

Screen Description
Display	Content
*a: Device Name List No. 1	Device Name List No. 1 displays some of the devices that make up the audio and visual system The names of the components from Device Name List No. 1 are shown in the following table
*b: Check Result	Result codes for all devices are displayed
*c: Memory Clear	Present and history DTCs and registered connected device names are cleared Press the "Memory CLR" switch for 3 seconds
*d: Recheck	A system check will be performed again after the memory is cleared The "Recheck" switch will dim during a system check
*e: Device Name List No. 2	Device Name List No. 2 displays some of the devices that make up the audio and visual system The names of the components from Device Name List No. 2 are shown in the following table

*a: Device Name List No. 1 Description
Name	Component	Connection Method
DA	Radio and display receiver assembly	-
AMP	Stereo component amplifier assembly	-

*b: Check Result Description
Result	Meaning	Action
OK	The device does not respond with a DTC	-
DETAIL	The device responds with a DTC	Look up the DTC in "Unit Check Mode"
NCON	The device was previously present, but does not respond in diagnostic mode	Check power supply wire harness of the device
NRES	The device responds in diagnostic mode, but gives no DTC information	Check power supply wire harness of the device

*e: Device Name List No. 2 Description
Name	Component	Connection Method
AUX	No. 1 stereo jack adapter assembly	Vehicle wire harness

Unit check mode screen description

Screen Description
Display	Content
*a: Device name	Target device
*b: History DTC	Diagnostic memory results and stored DTCs are displayed.
*c: Current DTC	DTCs output in the service check are displayed.
*d: DTC	DTC (Diagnostic Trouble Code)
*e: Diagnosis clear switch	Pushing this switch for 3 seconds clears the diagnostic memory data of the target device (Both response to diagnostic system check result and the displayed data are cleared.).

Tech Tips

This screen is updated once per second.
A maximum of 6 DTCs can be displayed for history and present DTCs.

Read the system check result.
1. If the check result is "DETAIL", touch the displayed check result to view the results on the "Unit Check Mode" screen and record them.
  
  Note
  
  A maximum of 6 DTCs can be displayed for history and present DTCs on the "Unit check mode" screen. Therefore, when 6 DTCs are displayed, troubleshoot those DTCs first and then check the "Unit check mode" screen again to see if any other DTCs are displayed.
  Tech Tips
  - When all results are "OK", this means that no DTCs are stored.
  - When proceeding to view the results of another device, press the "Back" switch to return to the "System Check Mode" screen. Repeat the step above to view the results of other devices.
2. Check the details of the DTC(s).
  
  Click here

DTC CLEAR/RECHECK (CLEAR USING SYSTEM CHECK MODE SCREEN)

Clear DTCs
1. Press the "Memory CLR" switch for 3 seconds.
2. Confirm that the check results are cleared.
  Tech Tips
  - To clear the DTCs for a specific device, clear the DTCs using the "Unit Check Mode" screen.
  - When clearing the DTCs using the "Unit Check Mode" screen, press the "Code CLR" switch for 3 seconds.
Recheck
1. Press the "Recheck" switch.
2. Confirm that all diagnostic codes are "OK" when the check results are displayed. If a code other than "OK" is displayed, troubleshoot again.
  
  Tech Tips
  
  When DTCs are cleared using the "Unit Check Mode" screen, press the "Back" switch to return to the "System Check Mode" screen and perform this operation.

FINISH DIAGNOSTIC MODE

Turn the ignition switch off.

AUDIO AND VISUAL SYSTEM(for Radio and Display Type) DTC CHECK / CLEAR