REAR SUSPENSION MEMBER INSTALLATION

PROCEDURE


  1. INSTALL REAR NO. 1 DIFFERENTIAL MOUNT CUSHION (for 4WD/AWD)

    Click here

  2. INSTALL REAR SUSPENSION MEMBER SUB-ASSEMBLY


    1. A01V7TBC02
      *a Attachment Placement Positions

      Place wooden blocks or plate lift attachments on an engine lifter, and then set the rear suspension member sub-assembly so that the attachments are in the positions shown in the illustration.

      Note


      • Place the wooden blocks or plate lift attachments so that the rear suspension member sub-assembly is level.

      • As the rear suspension member sub-assembly is very heavy, be sure to support it securely.

    2. A01VAFK

      Install the rear suspension member and 2 rear upper body mounting cushions with the 2 bolts and 2 nuts.

      Torque:
      125 N*m  { 1275 kgf*cm, 92 ft.*lbf }

  3. INSTALL REAR DIFFERENTIAL CARRIER ASSEMBLY (for 4WD/AWD)

    Click here

  4. INSTALL PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY (for 4WD/AWD)

    Click here

  5. TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY LH


    1. Temporarily install the upper control arm to the rear suspension member with the bolt and nut.

  6. TEMPORARILY INSTALL REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  7. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  8. TEMPORARILY INSTALL REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  9. INSTALL REAR LOWER COIL SPRING INSULATOR LH

    Click here

  10. INSTALL REAR LOWER COIL SPRING INSULATOR RH

    Tech Tips

    Use the same procedure described for the LH side.

  11. INSTALL REAR UPPER COIL SPRING INSULATOR LH

    Click here

  12. INSTALL REAR UPPER COIL SPRING INSULATOR RH

    Tech Tips

    Use the same procedure described for the LH side.

  13. INSTALL REAR COIL SPRING LH

    Click here

  14. INSTALL REAR COIL SPRING RH

    Tech Tips

    Use the same procedure described for the LH side.

  15. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY LH

    Click here

  16. TEMPORARILY INSTALL REAR SHOCK ABSORBER ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  17. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY LH


    1. Install the rear axle carrier to the rear upper control arm with the bolt and nut.

      Torque:
      90 N*m  { 918 kgf*cm, 66 ft.*lbf }

      Note

      Since a stopper nut is used, tighten the bolt.

  18. INSTALL REAR AXLE CARRIER SUB-ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  20. TEMPORARILY INSTALL REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  21. CONNECT REAR TRAILING ARM ASSEMBLY LH


    1. Connect the rear trailing arm to the rear axle carrier with the 2 bolts.

      Torque:
      200 N*m  { 2039 kgf*cm, 148 ft.*lbf }

  22. CONNECT REAR TRAILING ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  23. INSTALL REAR STABILIZER BAR

    Click here

  24. INSTALL REAR STABILIZER LINK ASSEMBLY LH

    Click here

  25. INSTALL REAR STABILIZER LINK ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  26. INSTALL REAR SUSPENSION MEMBER BRACE LH

    Click here

  27. INSTALL REAR SUSPENSION MEMBER BRACE RH

    Tech Tips

    Use the same procedure described for the LH side.

  28. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for 2WD)

    Click here

  29. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH (for 2WD)

    Tech Tips

    Use the same procedure described for the LH side.

  30. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY LH (for 4WD/AWD)

    Click here

  31. INSTALL REAR AXLE HUB AND BEARING ASSEMBLY RH (for 4WD/AWD)

    Tech Tips

    Use the same procedure described for the LH side.

  32. INSTALL PARKING BRAKE ASSEMBLY

    Click here

  33. INSTALL REAR DISC

    Click here

  34. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY LH

    Click here

  35. CONNECT REAR DISC BRAKE CALIPER ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  36. CONNECT NO. 3 PARKING BRAKE CABLE ASSEMBLY

    Click here

  37. CONNECT NO. 2 PARKING BRAKE CABLE ASSEMBLY

    Tech Tips

    Use the same procedure described for the No. 3 parking brake cable assembly.

  38. CONNECT SKID CONTROL SENSOR WIRE LH (for 2WD)

    Click here

  39. CONNECT SKID CONTROL SENSOR WIRE RH (for 2WD)

    Tech Tips

    Use the same procedure described for the LH side.

  40. CONNECT REAR SPEED SENSOR LH (for 4WD/AWD)

    Click here

  41. CONNECT REAR SPEED SENSOR RH (for 4WD/AWD)

    Tech Tips

    Use the same procedure described for the LH side.

  42. INSTALL REAR AXLE SHAFT NUT LH (for 4WD/AWD)

    Click here

  43. INSTALL REAR AXLE SHAFT NUT RH (for 4WD/AWD)

    Tech Tips

    Use the same procedure described for the LH side.

  44. STABILIZE SUSPENSION

    Click here

  45. TIGHTEN REAR SHOCK ABSORBER ASSEMBLY LH

    Click here

  46. TIGHTEN REAR SHOCK ABSORBER ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  47. TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY LH

    Click here

  48. TIGHTEN REAR UPPER CONTROL ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  49. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY LH

    Click here

  50. TIGHTEN REAR NO. 2 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  51. TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY LH

    Click here

  52. TIGHTEN REAR NO. 1 SUSPENSION ARM ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  53. INSTALL REAR HEIGHT CONTROL SENSOR SUB-ASSEMBLY LH (w/ Automatic Headlight Beam Level Control System)

    Click here

  54. INSTALL REAR WHEEL

    Torque:
    103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  55. INSPECT AND ADJUST REAR WHEEL ALIGNMENT

    Click here

  56. ADJUST HEADLIGHT ASSEMBLY

    Click here

  57. INSPECT SPEED SENSOR SIGNAL

    w/o VSC: Click here

    w/ VSC: Click here