FRONT DRIVE SHAFT ASSEMBLY(for 2WD) DISASSEMBLY

CAUTION / NOTICE / HINT

Note


  • When using a vise, place aluminum plates between the part and vise.

  • When using a vise, do not overtighten it.

PROCEDURE


  1. DISCONNECT FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH

    A01QPZ1C02
    *A for One Touch Type
    *B for Claw Engagement Type
    *a Claw Engagement

    1. for One Touch Type:

      Using a screwdriver, disconnect the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.

    2. for Claw Engagement Type:

      Using needle-nose pliers, detach the claw engagement and disconnect the front No. 2 axle inboard joint boot clamp LH.

  2. DISCONNECT FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. DISCONNECT FRONT AXLE INBOARD JOINT BOOT CLAMP LH

    Tech Tips

    Use the same procedure described for the front No. 2 axle inboard joint boot clamp LH.

  4. DISCONNECT FRONT AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. DISCONNECT FRONT AXLE INBOARD JOINT BOOT

    Tech Tips

    Use the same procedure for the RH and LH sides.


    1. Disconnect the front axle inboard joint boot from the front drive inboard joint assembly.

  6. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH

    A01QOD4C04
    *a Matchmark

    1. Remove any old grease from the front drive inboard joint assembly LH.

    2. Put matchmarks on the front drive inboard joint assembly LH and front drive outboard joint shaft assembly LH.

      Note

      Do not use a punch to make the matchmarks.

    3. Remove the front drive inboard joint assembly LH from the front drive outboard joint shaft assembly LH.

    4. A01QPB5

      Using a snap ring expander, remove the snap ring.

    5. A01QOV9C03
      *a Matchmark

      Put matchmarks on the front drive outboard joint shaft assembly LH and tripod joint.

      Note

      Do not use a punch to make the matchmarks.

    6. Using a brass bar and hammer, remove the tripod joint from the front drive outboard joint shaft assembly LH.

      Note


      • Do not tap the rollers.

      • Do not drop the tripod joint.

    7. Remove the front No. 2 axle inboard joint boot clamp LH, front axle inboard joint boot and front axle inboard joint boot clamp LH.

  7. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. DISCONNECT FRONT DRIVE SHAFT DAMPER CLAMP LH (w/ Drive Shaft Damper)


    1. A01QRDVC02
      *a Claw Engagement

      w/ 1 Clamp:

      Using needle-nose pliers, detach the claw engagement and disconnect the front drive shaft damper clamp LH.

    2. A01QTKMC02
      *a Claw Engagement

      w/ 2 Clamps:

      Using needle-nose pliers, detach the claw engagement and disconnect the 2 front drive shaft damper clamp LH.

      Tech Tips

      Use the same procedure for each front drive shaft damper clamp LH.

  9. DISCONNECT FRONT DRIVE SHAFT DAMPER CLAMP RH (w/ Drive Shaft Damper)

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE FRONT DRIVE SHAFT DAMPER LH (w/ Drive Shaft Damper)


    1. w/ 1 Clamp:

      Remove the front drive shaft damper LH and front drive shaft damper clamp LH from the front drive outboard joint shaft assembly LH.

    2. w/ 2 Clamps:

      Remove the front drive shaft damper LH and 2 front drive shaft damper clamp LH from the front drive outboard joint shaft assembly LH.

  11. REMOVE FRONT DRIVE SHAFT DAMPER RH (w/ Drive Shaft Damper)

    Tech Tips

    Use the same procedure described for the LH side.

  12. DISCONNECT FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH

    A01QUJN

    1. Using a screwdriver, disconnect the front No. 2 axle outboard joint boot clamp LH as shown in the illustration.

  13. DISCONNECT FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. DISCONNECT FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

    Tech Tips

    Use the same procedure described for the front No. 2 axle outboard joint boot clamp LH.

  15. DISCONNECT FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE FRONT AXLE OUTBOARD JOINT BOOT

    Tech Tips

    Use the same procedure for the RH and LH sides.


    1. Remove the front No. 2 axle outboard joint boot clamp, front axle outboard joint boot and front axle outboard joint boot clamp from the front drive outboard joint shaft assembly.

    2. Remove any old grease from the front drive outboard joint shaft assembly.

  17. REMOVE FRONT DRIVE SHAFT DUST COVER LH

    A01QTK0N02

    1. Using SST and a press, remove the front drive shaft dust cover LH from the front drive inboard joint assembly LH.

      SST
      09950-00020

      Note

      Do not drop the front drive inboard joint assembly LH.

  18. REMOVE FRONT DRIVE SHAFT DUST COVER RH


    1. A01QQPAN01

      Using SST and a press, remove the front drive shaft dust cover RH from the front drive inboard joint assembly RH.

      SST
      09950-00020

      Note

      Do not drop the front drive inboard joint assembly RH.

  19. REMOVE DRIVE SHAFT BEARING CASE SUB-ASSEMBLY (for RH Side)


    1. w/ Drive Shaft Bearing Case:


      1. A01QQ5HC01
        *A for 2AR-FE, 3ZR-FE
        *B for 2WW

        Using a screwdriver, remove the bearing case snap ring from the drive shaft bearing case sub-assembly.

      2. A01QUNDC01
        *A for 2AR-FE, 3ZR-FE
        *B for 2WW

        Using a press, remove the drive shaft bearing case sub-assembly from the front drive inboard joint assembly RH.

        Note

        Do not drop the front drive inboard joint assembly RH.

  20. REMOVE FRONT DRIVE SHAFT DUST COVER (for RH Side)


    1. A01QSFKN02

      Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly RH.

      SST
      09950-00020

      Note

      Do not drop the front drive inboard joint assembly RH.

  21. REMOVE FRONT DRIVE SHAFT BEARING (for RH Side)

    A01QT6Y

    1. Using a snap ring expander, remove the snap ring.

    2. A01QOZVN03

      Using SST and a press, remove the front drive shaft bearing from the front drive inboard joint assembly RH.

      SST
      09527-10011

      Note

      Do not drop the front drive inboard joint assembly RH.