FRONT DRIVE SHAFT ASSEMBLY(for 2WD) DISASSEMBLY

CAUTION / NOTICE / HINT

Note


  • When using a vise, place aluminum plates between the part and vise.

  • When using a vise, do not overtighten it.

PROCEDURE


  1. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH

    A00YU0GC01
    *A for One Touch Type
    *B for Claw Engagement Type

    1. for One Touch Type:

      Using a screwdriver, remove the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.

    2. for Claw Engagement Type:

      Using needle-nose pliers, remove the front No. 2 axle inboard joint boot clamp LH as shown in the illustration.

  2. REMOVE FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  3. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP LH

    Tech Tips

    Use the same procedure described for the front No. 2 axle inboard joint boot clamp LH.

  4. REMOVE FRONT AXLE INBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  5. DISCONNECT FRONT AXLE INBOARD JOINT BOOT


    1. Disconnect the front axle inboard joint boot from the front drive inboard joint assembly.

  6. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY LH

    A00YUY9C04
    *a Matchmark

    1. Remove any old grease from the front drive inboard joint assembly LH.

    2. Put matchmarks on the front drive inboard joint assembly LH and front drive outboard joint shaft assembly LH.

      Note

      Do not use a punch to make the matchmarks.

    3. Remove the front drive inboard joint assembly LH from the front drive outboard joint shaft assembly LH.

    4. A00YV0Z

      Using a snap ring expander, remove the snap ring.

    5. A00YTLUC03
      *a Matchmark

      Put matchmarks on the front drive outboard joint shaft assembly LH and tripod joint.

      Note

      Do not use a punch to make the matchmarks.

    6. Using a brass bar and hammer, remove the tripod joint from the front drive outboard joint shaft assembly LH.

      Note

      Do not tap the rollers.

    7. Remove the front axle inboard joint boot.

  7. REMOVE FRONT DRIVE INBOARD JOINT ASSEMBLY RH

    Tech Tips

    Use the same procedure described for the LH side.

  8. REMOVE FRONT DRIVE SHAFT DAMPER CLAMP LH (w/ Drive Shaft Damper)

    A00YS11C01
    *A for One Touch Type
    *B for Claw Engagement Type

    1. for One Touch Type:

      Using a screwdriver, remove the front drive shaft damper clamp LH as shown in the illustration.

    2. for Claw Engagement Type:

      Using needle-nose pliers, remove the front drive shaft damper clamp LH as shown in the illustration.

  9. REMOVE FRONT DRIVE SHAFT DAMPER CLAMP RH (w/ Drive Shaft Damper)

    Tech Tips

    Use the same procedure described for the LH side.

  10. REMOVE FRONT DRIVE SHAFT DAMPER LH (w/ Drive Shaft Damper)


    1. Remove the front drive shaft damper LH from the front drive outboard joint shaft assembly LH.

  11. REMOVE FRONT DRIVE SHAFT DAMPER RH (w/ Drive Shaft Damper)

    Tech Tips

    Use the same procedure described for the LH side.

  12. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH

    A00YRQW

    1. Using a screwdriver, remove the front No. 2 axle outboard joint boot clamp LH as shown in the illustration.

  13. REMOVE FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  14. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH

    Tech Tips

    Use the same procedure described for the front No. 2 axle outboard joint boot clamp LH.

  15. REMOVE FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH

    Tech Tips

    Use the same procedure described for the LH side.

  16. REMOVE FRONT AXLE OUTBOARD JOINT BOOT


    1. Remove the front axle outboard joint boot from the front drive outboard joint shaft assembly.

    2. Remove any old grease from the front drive outboard joint shaft assembly.

  17. REMOVE FRONT DRIVE SHAFT DUST COVER LH

    A00YUL1N02

    1. Using SST and a press, remove the front drive shaft dust cover LH.

      SST
      09950-00020

      Note

      Be careful not to drop the front drive inboard joint assembly LH.

  18. REMOVE FRONT DRIVE SHAFT DUST COVER RH

    Tech Tips

    Use the same procedure described for the LH side.

  19. REMOVE DRIVE SHAFT BEARING CASE SUB-ASSEMBLY


    1. w/ Drive Shaft Bearing Case:


      1. A00YRRK

        Using a screwdriver, remove the bearing case snap ring from the drive shaft bearing case sub-assembly.

      2. A00YQYU

        Using a press, remove the drive shaft bearing case sub-assembly from the front drive inboard joint assembly RH.

        Note

        Be careful not to drop the front drive inboard joint assembly RH.

  20. REMOVE FRONT DRIVE SHAFT DUST COVER


    1. A00YRJ4N02

      Using SST and a press, remove the front drive shaft dust cover from the front drive inboard joint assembly RH.

      SST
      09950-00020

      Note

      Be careful not to drop the front drive inboard joint assembly RH.

  21. REMOVE FRONT DRIVE SHAFT BEARING

    A00YXN9

    1. Using a snap ring expander, remove the snap ring.

    2. A00YV91N03

      Using SST and a press, remove the front drive shaft bearing from the front drive inboard joint assembly RH.

      SST
      09527-10011

      Note

      Be careful not to drop the front drive inboard joint assembly RH.