FRONT DRIVE SHAFT ASSEMBLY(for 2WD) COMPONENTS
ILLUSTRATION
| *A | for 1AD-FTV | - | - |
| *1 | NO. 1 ENGINE UNDER COVER | *2 | REAR ENGINE UNDER COVER LH |
| *3 | REAR ENGINE UNDER COVER RH | - | - |
ILLUSTRATION
| *A | for 2AR-FE | *B | for Full Cover Type |
| *C | for Half Cover Type | - | - |
| *1 | NO. 1 ENGINE UNDER COVER | *2 | REAR ENGINE UNDER COVER LH |
| *3 | REAR ENGINE UNDER COVER RH | - | - |
ILLUSTRATION
| *A | for 3ZR-FE | - | - |
| *1 | NO. 1 ENGINE UNDER COVER | *2 | REAR ENGINE UNDER COVER LH |
| *3 | REAR ENGINE UNDER COVER RH | - | - |
ILLUSTRATION
| *1 | FRONT AXLE SHAFT NUT LH | *2 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH |
| *3 | FRONT SPEED SENSOR LH | *4 | FRONT STABILIZER LINK ASSEMBLY LH |
| *5 | STEERING KNUCKLE WITH AXLE HUB LH | *6 | FRONT BRAKE FLEXIBLE HOSE |
| *a | for Axle Hub Spline Diameter 26 mm (1.02 in.) | *b | for Axle Hub Spline Diameter 30 mm (1.18 in.) |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
MP grease |  |
Do not apply lubricants to the threaded parts |
ILLUSTRATION
| *A | for 1AD-FTV | - | - |
| *1 | FRONT DRIVE SHAFT ASSEMBLY LH | *2 | FRONT DRIVE SHAFT ASSEMBLY RH |
| *3 | FRONT DRIVE SHAFT HOLE SNAP RING LH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *A | for 2AR-FE | *B | for Automatic Transaxle |
| *C | for Manual Transaxle | - | - |
| *1 | FRONT DRIVE SHAFT ASSEMBLY LH | *2 | FRONT DRIVE SHAFT ASSEMBLY RH |
| *3 | FRONT DRIVE SHAFT HOLE SNAP RING LH | *4 | DRIVE SHAFT BEARING BRACKET HOLE SNAP RING |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *A | for 3ZR-FE | *B | for Manual Transaxle |
| *C | for CVT | - | - |
| *1 | FRONT DRIVE SHAFT ASSEMBLY LH | *2 | FRONT DRIVE SHAFT ASSEMBLY RH |
| *3 | FRONT DRIVE SHAFT HOLE SNAP RING LH | - | - |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | - | - |
ILLUSTRATION
| *A | for LH Side | *B | w/ Drive Shaft Damper |
| *C | w/ 1 Clamp | *D | w/ 2 Clamps |
| *1 | FRONT AXLE INBOARD JOINT BOOT | *2 | FRONT AXLE INBOARD JOINT BOOT CLAMP LH |
| *3 | FRONT AXLE OUTBOARD JOINT BOOT | *4 | FRONT AXLE OUTBOARD JOINT BOOT CLAMP LH |
| *5 | FRONT DRIVE INBOARD JOINT ASSEMBLY LH | *6 | FRONT DRIVE SHAFT DAMPER CLAMP LH |
| *7 | FRONT DRIVE SHAFT DAMPER LH | *8 | FRONT DRIVE SHAFT DUST COVER LH |
| *9 | FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP LH | *10 | FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP LH |
| *11 | SNAP RING | *12 | TRIPOD JOINT |
| *13 | FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY LH | - | - |
| ● | Non-reusable part | - | - |
ILLUSTRATION
| *A | for RH Side | *B | w/ Drive Shaft Damper |
| *C | w/o Drive Shaft Bearing Case | *D | w/ Drive Shaft Bearing Case |
| *E | w/ 1 Clamp | *F | w/ 2 Clamps |
| *1 | DRIVE SHAFT BEARING CASE SUB-ASSEMBLY | *2 | FRONT AXLE INBOARD JOINT BOOT |
| *3 | FRONT AXLE INBOARD JOINT BOOT CLAMP RH | *4 | FRONT AXLE OUTBOARD JOINT BOOT |
| *5 | FRONT AXLE OUTBOARD JOINT BOOT CLAMP RH | *6 | FRONT DRIVE INBOARD JOINT ASSEMBLY RH |
| *7 | FRONT DRIVE SHAFT BEARING | *8 | FRONT DRIVE SHAFT DAMPER CLAMP RH |
| *9 | FRONT DRIVE SHAFT DAMPER RH | *10 | FRONT DRIVE SHAFT DUST COVER |
| *11 | FRONT DRIVE SHAFT DUST COVER RH | *12 | FRONT NO. 2 AXLE INBOARD JOINT BOOT CLAMP RH |
| *13 | FRONT NO. 2 AXLE OUTBOARD JOINT BOOT CLAMP RH | *14 | TRIPOD JOINT |
| *15 | SNAP RING | *16 | FRONT DRIVE OUTBOARD JOINT SHAFT ASSEMBLY RH |
| ● | Non-reusable part | - | - |