CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM, Diagnostic DTC:P099B, P099C

DTC Code DTC Name
P099B Shift Solenoid "G" Control Circuit Low (Shift Solenoid Valve SC)
P099C Shift Solenoid "G" Control Circuit High (Shift Solenoid Valve SC)

DESCRIPTION

Based on the signal received by the shift solenoid valve SC, the ECM uses the shift solenoid valve SLU to control the forward and reverse clutch pressure.

If there is an open or short in the shift solenoid valve SC circuit, the ECM stops sending current to the defective shift solenoid valve.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P099B Shift Solenoid "G" Control Circuit Low (Shift Solenoid Valve SC)

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. The vehicle is being driven.

  2. There is a short in the shift solenoid valve SC circuit.

  3. 3 seconds

  4. 1-trip detection logic

  • Harness or connector

  • Continuously variable transaxle assembly (Shift solenoid valve SC)

  • ECM

 Comes on DTC stored
P099C Shift Solenoid "G" Control Circuit High (Shift Solenoid Valve SC)

1. Diagnosis Condition 2. Malfunction Status 3. Malfunction Time 4. Other


  1. The vehicle is being driven.

  2. There is an open in the shift solenoid valve SC circuit.

  3. 0.5 seconds

  4. 1-trip detection logic

  • Harness or connector

  • Continuously variable transaxle assembly (Shift solenoid valve SC)

  • ECM

 Comes on DTC stored

MONITOR DESCRIPTION

These DTCs indicate an open or short in the shift solenoid valve SC circuit. If there is an open or short in the shift solenoid valve SC circuit, the ECM detects the problem and stores a DTC.

WIRING DIAGRAM

A01QQ10E48
*1 Shift Solenoid Valve SC
*2 Continuously Variable Transaxle Assembly (Transmission Wire)

CAUTION / NOTICE / HINT

Note


  • Perform initialization when parts related to the continuously variable transaxle are replaced.

    Click here

  • Check that no DTCs are stored after performing initialization.

    Click here

PROCEDURE


  1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SC)


    1. A01QPFJC08
      *a

      Component without harness connected

      (Transmission Wire)

      Disconnect the transmission wire connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      10 (SC) - Body ground 20°C (68°F) 11 to 15 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY Click here

    OK

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - ECM)


    1. A01QPVYC02
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B93-41 (SC) - Body ground 20°C (68°F) 11 to 15 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR (TRANSMISSION WIRE - ECM)

    OK

  3. REPLACE ECM


    1. Replace the ECM.


      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here

  4. REPLACE CONTINUOUSLY VARIABLE TRANSAXLE ASSEMBLY


    1. Replace the continuously variable transaxle assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here