CONTINUOUSLY VARIABLE TRANSAXLE SYSTEM Transmission Control Switch Circuit

DESCRIPTION

After moving the shift lever to M, it is possible to switch the shift range between "1" (M1 gear) and "7" (M7 gear) using the transmission control switch.

Moving the shift lever to "+" once raises the shift range by one, and moving the shift lever to "-" lowers the shift range by one.

WIRING DIAGRAM

A01QR9NE01

CAUTION / NOTICE / HINT

Note


  • Perform initialization when parts related to the continuously variable transaxle are replaced.

    Click here

  • Check that no DTCs are stored after performing initialization.

    Click here

  • Inspect the fuses for circuits related to this system before performing the following procedure.

PROCEDURE


  1. CHECK HARNESS AND CONNECTOR (BATTERY - TRANSMISSION CONTROL SWITCH)


    1. A01QSH1C12
      *a

      Front view of wire harness connector

      (to Transmission Control Switch)

      Disconnect the transmission control switch connector.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Switch Condition Specified Condition
      G36-4 (IG) - Body ground Ignition switch ON 11 to 14 V
      G36-4 (IG) - Body ground Ignition switch off Below 1 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK POWER SOURCE CIRCUIT

    OK

  2. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - BODY GROUND)


    1. A01QSH1C13
      *a

      Front view of wire harness connector

      (to Transmission Control Switch)

      Disconnect the transmission control switch connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      G36-2 (E) - Body ground Always Below 1 Ω
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. INSPECT TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY)


    1. Disconnect the transmission control switch connector.

    2. A01QQC4C11
      *A for LHD
      *a

      Component without harness connected

      (Transmission Control Switch)

      for LHD:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
      3 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
      1 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
      4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
      3 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
      1 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher
    3. A01QQC4C14
      *A for RHD
      *a

      Component without harness connected

      (Transmission Control Switch)

      for RHD:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      4 (IG) - 5 (S) Shift lever in M, "+" or "-" Below 1 Ω
      1 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω
      3 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω
      4 (IG) - 5 (S) Shift lever not in M, "+" or "-" 10 kΩ or higher
      1 (SFTU) - 2 (E) Shift lever in M 10 kΩ or higher
      3 (SFTD) - 2 (E) Shift lever in M 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE TRANSMISSION CONTROL SWITCH (TRANSMISSION FLOOR SHIFT ASSEMBLY) Click here

    OK

  4. CHECK HARNESS AND CONNECTOR (TRANSMISSION CONTROL SWITCH - ECM)


    1. A01QUBIC02
      *a

      Front view of wire harness connector

      (to ECM)

      Disconnect the ECM connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A62-41 (S) - Body ground

      • Ignition switch ON

      • Shift lever in M, "+" or "-"

      		 11 to 14 V
      A62-41 (S) - Body ground

      • Ignition switch ON

      • Shift lever not in M, "+" or "-"

      		 Below 1 V

    4. Turn the ignition switch off.

    5. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A62-42 (SFTU) - Body ground Shift lever held in "+" (Up-shift) Below 1 Ω
      A62-43 (SFTD) - Body ground Shift lever held in "-" (Down-shift) Below 1 Ω
      A62-42 (SFTU) - Body ground Shift lever in M 10 kΩ or higher
      A62-43 (SFTD) - Body ground Shift lever in M 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  5. REPLACE ECM


    1. Replace the ECM.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

    PERFORM INITIALIZATION Click here