MANUAL TRANSAXLE UNIT COMPONENTS
ILLUSTRATION
| *A | w/o Stop and Start System | *B | w/ Stop and Start System |
| *1 | BACK-UP LIGHT SWITCH ASSEMBLY | *2 | BREATHER PLUG |
| *3 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY | *4 | CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY |
| *5 | CONTROL CABLE BRACKET ASSEMBLY | *6 | MANUAL TRANSMISSION DRAIN PLUG |
| *7 | MANUAL TRANSMISSION FILLER PLUG | *8 | NEUTRAL POSITION SWITCH |
| *9 | RELEASE CYLINDER BLEEDER PLUG | *10 | RELEASE CYLINDER BLEEDER PLUG CAP |
| *11 | TRANSMISSION CASE PLUG | *12 | MANUAL TRANSAXLE ASSEMBLY |
| *13 | BLEEDER CLUTCH RELEASE TUBE | *14 | GASKET |
| *15 | CLUTCH BOOT TUBE | - | - |
 |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
 |
Clutch spline grease | - | - |
ILLUSTRATION
| *1 | LOCK BALL PIN | *2 | MANUAL TRANSMISSION CASE |
| *3 | OUTER SHIFT LEVER E-RING | *4 | REVERSE IDLER GEAR SHAFT BOLT |
| *5 | SHIFT DETENT BALL | *6 | STRAIGHT PIN |
| *7 | SHIFT DETENT BALL COMPRESSION SPRING | *8 | SHIFT DETENT BALL PLUG |
| *9 | SHIFT AND SELECT LEVER SHAFT STRAIGHT SCREW WITH HEAD PLUG | *10 | SHIFT AND SELECT LEVER SHAFT COMPRESSION SPRING |
| *11 | FRONT TRANSAXLE CASE | *12 | GASKET |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| ★ | Precoated part | - | - |
ILLUSTRATION
| *1 | DIFFERENTIAL CASE ASSEMBLY | *2 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING |
| *3 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING | *4 | INPUT SHAFT ASSEMBLY |
| *5 | OUTER SELECT LEVER | *6 | OUTER SELECT LEVER OIL SEAL |
| *7 | REVERSE IDLER GEAR SUB-ASSEMBLY | *8 | REVERSE SHIFT ARM BRACKET ASSEMBLY |
| *9 | REVERSE SHIFT FORK | *10 | REVERSE SHIFT FORK SHAFT ASSEMBLY |
| *11 | SHIFT AND SELECT LEVER SHAFT ASSEMBLY | *12 | SHIFT INTERLOCK PLATE |
| *13 | INNER SELECT LEVER | *14 | INNER SELECT LEVER BOLT |
| *15 | REVERSE SHIFT FORK SLOTTED SPRING PIN | *16 | REVERSE IDLER THRUST WASHER |
| *17 | REVERSE IDLER GEAR SHAFT | *18 | NO. 1 GEAR SHIFT FORK SHAFT ASSEMBLY |
| *19 | NO. 2 GEAR SHIFT FORK SHAFT ASSEMBLY | *20 | OUTPUT SHAFT ASSEMBLY |
| |
N*m (kgf*cm, ft.*lbf): Specified torque | ● | Non-reusable part |
| |
MP grease | ★ | Precoated part |
ILLUSTRATION
| *1 | FRONT DIFFERENTIAL CASE FRONT TAPERED ROLLER BEARING | *2 | FRONT OUTPUT SHAFT BEARING |
| *3 | FRONT TRANSAXLE CASE OIL SEAL | *4 | TRANSAXLE CASE OIL SEAL |
| *5 | TRANSMISSION MAGNET | *6 | FRONT DIFFERENTIAL OIL BAFFLE |
| *7 | FRONT TRANSAXLE CASE | *8 | OUTPUT SHAFT COVER |
| ● | Non-reusable part | |
MP grease |
ILLUSTRATION
| *1 | FRONT DIFFERENTIAL CASE REAR TAPERED ROLLER BEARING | *2 | INPUT SHAFT COVER |
| *3 | MANUAL TRANSMISSION CASE | *4 | NO. 1 OIL RECEIVER PIPE |
| *5 | OUTER NO. 1 SHIFT LEVER | *6 | OUTER SHIFT LEVER OIL SEAL |
| *7 | REAR INPUT SHAFT BEARING SHIM | *8 | REAR OUTPUT SHAFT BEARING |
| *9 | TRANSMISSION CASE OIL SEAL | *10 | OUTER SHIFT LEVER SPACER |
| *11 | INNER SHIFT LEVER SLOTTED SPRING PIN | *12 | INNER NO. 1 SHIFT LEVER |
| *13 | FRONT DIFFERENTIAL CASE REAR SHIM | *14 | REAR OUTPUT SHAFT BEARING SHIM |
| ● | Non-reusable part | |
MP grease |