SHIFT LEVER INSPECTION

PROCEDURE

1. INSPECT SHIFT LEVER ASSEMBLY (w/o Smart Key System)

   
   
   1. 

      *a	Component with harness connected (Floor Shift Lever Sub-assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition 1 (ACC) - Body ground Ignition switch ON 11 to 14 V Ignition switch ACC 11 to 14 V Ignition switch off Below 1 V 8 (STP) - Body ground Brake pedal depressed 11 to 14 V Brake pedal released Below 1 V 5 (KLS+) - Body ground Ignition switch ACC and shift lever in P Below 1 V Ignition switch ACC and shift lever except in P 11 to 14 V 4 (IG) - Body - ground Ignition switch ON 11 to 14 V Ignition switch off Below 1 V

      Tech Tips

      Do not disconnect the shift lever assembly connector.

      If the result is not as specified, replace the shift lever assembly.

   2. 

      *a	Component with harness connected (Floor Shift Lever Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 7 (E) - Body ground Always Below 1 Ω

      Tech Tips

      Do not disconnect the shift lever assembly connector.

      If the result is not as specified, replace the shift lever assembly.

2. INSPECT SHIFT LEVER ASSEMBLY (w/ Smart Key System)

   
   
   1. 

      *a	Component with harness connected (Floor Shift Lever Sub-assembly)

      Measure the voltage according to the value(s) in the table below.

      Standard Voltage

      Tester Connection Condition Specified Condition 1 (ACC) - Body ground Engine switch on (IG) 11 to 14 V Engine switch on (ACC) 11 to 14 V Engine switch off Below 1 V 8 (STP) - Body ground Brake pedal depressed 11 to 14 V Brake pedal released Below 1 V 2 (P2) - Body ground Engine switch on (ACC) and shift lever except in P Below 1 V Engine switch on (ACC) and shift lever in P 11 to 14 V 4 (IG) - Body - ground Engine switch on (IG) 11 to 14 V Engine switch off Below 1 V

      Tech Tips

      Do not disconnect the shift lever assembly connector.

      If the result is not as specified, replace the shift lever assembly.

   2. 

      *a	Component with harness connected (Floor Shift Lever Sub-assembly)

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 7 (E) - Body ground Always Below 1 Ω

      Tech Tips

      Do not disconnect the shift lever assembly connector.

      If the result is not as specified, replace the shift lever assembly.

3. INSPECT TRANSMISSION CONTROL SWITCH

   
   

   1. Disconnect the connector from the shift lever assembly.

   2. 

      *A	for LHD
      *a	Component without harness connected (Transmission control switch)

      for LHD:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω 3 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω 1 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω 4 (IG) - 5 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher 3 (SFTU) - 2 (E) Shift lever in S 10 kΩ or higher 1 (SFTD) - 2 (E) Shift lever in S 10 kΩ or higher

      If the result is not as specified, replace the shift lever assembly.

   3. 

      *A	for RHD
      *a	Component without harness connected (Transmission control switch)

      for RHD:

      Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition 4 (IG) - 5 (S) Shift lever in S, "+" or "-" Below 1 Ω 1 (SFTU) - 2 (E) Shift lever held in "+" (Up-shift) Below 1 Ω 3 (SFTD) - 2 (E) Shift lever held in "-" (Down-shift) Below 1 Ω 4 (IG) - 5 (S) Shift lever not in S, "+" or "-" 10 kΩ or higher 3 (SFTU) - 2 (E) Shift lever in S 10 kΩ or higher 1 (SFTD) - 2 (E) Shift lever in S 10 kΩ or higher

      If the result is not as specified, replace the shift lever assembly.