TIRE AND WHEEL SYSTEM INSPECTION

PROCEDURE


  1. INSPECT TIRES


    1. Check the tires for wear and proper inflation pressure.

      Cold Tire Inflation Pressure (for Korea)
      Tire Size

      Front

      kPa (kgf/cm2, psi)

      Rear

      kPa (kgf/cm2, psi)
      235/55R18 100H 220 (2.2, 32) 220 (2.2, 32)
      Cold Tire Inflation Pressure (for General Export)
      Tire Size

      Front

      kPa (kgf/cm2, psi)

      Rear

      kPa (kgf/cm2, psi)
      225/65R17 102H 220 (2.2, 32) 220 (2.2, 32)
      235/55R18 100H 220 (2.2, 32) 220 (2.2, 32)
      Cold Tire Inflation Pressure (for Europe)
      Tire Size

      Front

      kPa (kgf/cm2, psi)

      Rear

      kPa (kgf/cm2, psi)
      225/65R17 102H 240 (2.4, 35) 240 (2.4, 35)
      220 (2.2, 32)* 220 (2.2, 32)*
      235/55R18 100H 220 (2.2, 32) 220 (2.2, 32)
      225/60R18 100H 210 (2.1, 30) 210 (2.1, 30)

      *: for Ireland, Hungary, Romania and Turkey

      Cold Tire Inflation Pressure (for Compact Spare Tire)
      Tire Size

      kPa (kgf/cm2, psi)
      T165/80D17 104M 420 (4.2, 60)
    2. A01GANK

      Using a dial indicator, check the runout of the tires.

      Tire runout
      1.4 mm (0.0551 in.) or less

      Tech Tips

      Remove the wheel assembly from the vehicle, and measure the wheel assembly alone.

  2. ROTATE TIRES


    1. A01GA2JC01
      *a Front of the Vehicle
      *b Vehicle Wheels and Spare Tire Wheel are Same Type
      *c Vehicle Wheels and Spare Tire Wheel are Not Same Type, or There is No Spare Tire

      Rotate the tires as shown in the illustration.

      Torque:
      103 N*m  { 1050 kgf*cm, 76 ft.*lbf }

  3. INSPECT WHEEL BALANCE


    1. A01GDCJN01

      for Aluminum Wheel Type:

      Check and adjust the off-the-car balance.

      Maximum imbalance after adjustment
      8.0 g (0.0176 lb.)

      Note


      • Use a cleaning detergent to remove dirt, oil and water from the surface where the balance weight is to be adhered.

      • Do not touch the sticking surface of the tape.

      • Adhere a sticking type balance weight to the flat surface (A) shown in the illustration.

        Width (A)
        25 mm (0.984 in.)

      • Push the balance weight firmly to adhere it to the position.

      • Do not reuse the balance weight.

      Tech Tips


      • The inner side balance weights should be installed by clipping them to the rim.

      • If the tires vibrate even after off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.

    2. A01GCVU

      for Steel Wheel Type:

      Check and adjust the off-the-car balance.

      Maximum imbalance after adjustment
      8.0 g (0.0176 lb.)

      Tech Tips

      If the tires vibrate even after off-the-car balance adjustment, adjust the wheel balance with on-the-car balancing as necessary.

  4. INSPECT FRONT AXLE HUB BEARING LOOSENESS

    Click here

  5. INSPECT FRONT AXLE HUB RUNOUT

    Click here

  6. INSPECT REAR AXLE HUB BEARING LOOSENESS

    Click here

  7. INSPECT REAR AXLE HUB RUNOUT

    Click here