STOP AND START SYSTEM(for 1AD-FTV), Diagnostic DTC:P1540

DTC Code DTC Name
P1540 Brake Booster Sensor Circuit (Open or Short)

DESCRIPTION

The engine stop and start ECU determines changes in the brake booster assembly pressure based on the voltage signal received from the vacuum sensor assembly in the brake booster assembly.

If the engine stop and start ECU judges that the signal received from the vacuum sensor assembly is abnormal, it stores DTC P1540 and blinks the stop and start cancel indicator light.

A01QP3BE05
DTC No. Detection Item DTC Detection Condition Trouble Area Warning Indicate Memory
P1540 Brake Booster Sensor Circuit (Open or Short)

The following conditions continue for 2 seconds or more (1 trip detection logic):


  • Open or short in vacuum sensor assembly circuit

  • Ignition switch is turned to ON

  • Vacuum sensor assembly

  • Engine stop and start ECU

  • Wire harness or connector

 Blinking DTC stored

CONFIRMATION DRIVING PATTERN

Tech Tips

DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

Click here


  1. CONFIRMATION AFTER TROUBLESHOOTING


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON and turn the GTS on.

    3. Clear the DTCs.

      Click here


      Powertrain > Stop and Start > Clear DTCs

    4. Start the engine and allow it to idle for 15 seconds or more.

    5. Stop the engine and turn the ignition switch to ON.

    6. Turn the GTS on.

    7. Enter the following menus: Powertrain / Stop and Start / Data List / Brake Boost Pressure.


      Powertrain > Stop and Start > Data List
      Tester Display
      Brake Boost Pressure

    8. While depressing the brake pedal several times, check that the Brake Boost Pressure value changes.

    9. Check that DTCs are not output.

      Click here


      Powertrain > Stop and Start > Trouble Codes

  2. STOP AND START SYSTEM OPERATION CHECK

    Tech Tips

    When the cable is disconnected from the negative (-) battery terminal, stop and start control is prohibited for a certain amount of time. After connecting the cable, drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes).


    1. Start the engine and warm it up.

    2. Turn the air conditioning system off.

    3. Drive the vehicle at 7 km/h (4.3 mph) or more.

      CAUTION:

      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    4. Stop the vehicle, move the shift lever to neutral and release the clutch pedal.

    5. Allow the engine to stop by stop and start control.

    6. Depress the clutch pedal and start the engine.

WIRING DIAGRAM

A01QQDAE06
*a Vacuum Sensor Assembly
*b Engine Stop and Start ECU

CAUTION / NOTICE / HINT

Note


  • Before replacing the engine stop and start ECU, read the number of starter operations and write it into a new engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or air conditioning amplifier assembly, reset and perform learning of the air conditioning information in the engine stop and start ECU.

    Click here

  • After replacing the engine stop and start ECU or airbag sensor assembly, perform deceleration sensor zero point clear and calibration.

    Click here

Tech Tips


  • DTCs for the stop and start system are not cleared even if the malfunction has been repaired. After repairing the malfunction, be sure to clear the DTCs.

    Click here

  • Using the GTS, read the freeze frame data before troubleshooting. System condition information is recorded as freeze frame data the moment a DTC is stored. This information can be useful when troubleshooting.

    Click here

PROCEDURE


  1. CHECK VACUUM SENSOR ASSEMBLY (PB TERMINAL VOLTAGE)

    A01QPZRC01
    *a

    Component with harness connected

    (Engine Stop and Start ECU)

    		 - -

    1. Turn the ignition switch to ON.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A66-13 (PB) - A66-3 (BRE2) Ignition switch ON Higher than 0.6 V or below 4.7 V
      Result
      Proceed to
      OK
      NG

    OK

    USE SIMULATION METHOD TO CHECK Click here

    NG

  2. CHECK HARNESS AND CONNECTOR (ENGINE STOP AND START ECU - VACUUM SENSOR ASSEMBLY)


    1. Disconnect the A66 engine stop and start ECU connector.

    2. Disconnect the A60 vacuum sensor assembly connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      A66-13 (PB) - A60-2 (PB) Always Below 1 Ω
      A66-14 (BRVC) - A60-3 (VC) Always Below 1 Ω
      A66-3 (BRE2) - A60-1 (E2) Always Below 1 Ω
      A66-13 (PB) - Body ground Always 10 kΩ or higher
      A66-14 (BRVC) - Body ground Always 10 kΩ or higher
      A66-3 (BRE2) - Body ground Always 10 kΩ or higher
      A60-2 (PB) - Body ground Always 10 kΩ or higher
      A60-3 (VC) - Body ground Always 10 kΩ or higher
      A60-1 (E2) - Body ground Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  3. CHECK ENGINE STOP AND START ECU (BRVC TERMINAL VOLTAGE)

    A01QPZRC03
    *a

    Component with harness connected

    (Engine Stop and Start ECU)

    		 - -

    1. Turn the ignition switch to ON.

    2. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      A66-14 (BRVC) - A66-3 (BRE2) Ignition switch ON 4.75 to 5.25 V
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. REPLACE VACUUM SENSOR ASSEMBLY


    1. Replace the vacuum sensor assembly.

      Click here

      Result
      Proceed to
      NEXT

    NEXT

  5. CHECK DTC OUTPUT


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Stop and Start / Trouble Codes.

    5. Check that no DTCs are output.


      Powertrain > Stop and Start > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P1540 is output B

    A

    END

    B

    REPLACE ENGINE STOP AND START ECU Click here