STARTER DISASSEMBLY

PROCEDURE


  1. REMOVE MAGNET STARTER SWITCH ASSEMBLY


    1. A01M1GR

      Remove the nut and disconnect the field coil lead wire from terminal C.

    2. A01LXDX

      Using a T20 "TORX" socket wrench, remove the 3 screws that hold the magnet switch to the starter drive housing assembly.

    3. Remove the magnet switch from the starter drive housing assembly.

    4. A01M10VC01
      *1 Pinion Drive Lever
      *a Plunger
      *b Return Spring

      Remove the return spring.

    5. Remove the plunger from the pinion drive lever.

  2. REMOVE STARTER YOKE ASSEMBLY


    1. A01LVK3

      Remove the 2 through bolts and starter yoke assembly together with the starter armature assembly from the starter drive housing assembly.

  3. REMOVE STARTER BRUSH HOLDER ASSEMBLY


    1. A01M00O

      Secure the starter yoke assembly in a vise between aluminum plates.

      Note

      Do not overtighten the vise.

    2. Remove the 2 screws and starter commutator end frame cover from the starter commutator end frame.

    3. A01M1ELC03
      *a Slotted Washer

      Remove the slotted washer.

      Note

      Use caution to prevent the starter armature assembly from dropping.

    4. A01LVGOC07
      *a Washer
      *b Starter Commutator End Frame

      Remove the 2 washers from the starter commutator end frame.

      Note

      Use caution to prevent the starter armature assembly from dropping.

    5. Remove the starter commutator end frame from the starter yoke assembly.

      Note

      Use caution to prevent the starter armature assembly from dropping.

    6. A01LVFXC05
      *1 Starter Brush Holder Assembly
      *a Rubber
      *b Spring

      Remove the starter brush holder assembly from the starter armature assembly.

      Note


      • Do not pull on the rubber.

      • Use caution to prevent the starter armature assembly from dropping.

  4. REMOVE STARTER ARMATURE ASSEMBLY


    1. A01M34PC01
      *1 Starter Yoke Assembly
      *2 Starter Armature Assembly

      Remove the starter armature assembly from the starter yoke assembly.

  5. REMOVE STARTER CLUTCH SUB-ASSEMBLY


    1. A01LXIW

      Disengage the 3 claws and remove the frame end cover from the plate.

    2. A01M2CM

      Disengage the 3 claws and remove the plate from the planet carrier.

    3. A01LXKG

      Remove the 3 planetary gears from the planet carrier shaft sub-assembly.

    4. A01LZ3IC01
      *1 Pinion Drive Lever
      *2 Starter Drive Housing Cover
      *3 Starter Drive Housing Assembly
      *a Starter Center Bearing Clutch

      Remove the starter center bearing clutch, pinion drive lever and starter drive housing cover from the starter drive housing assembly.

    5. A01M1RJC01
      *1 Pinion Stop Collar
      *2 Starter Clutch Sub-assembly

      Using a screwdriver, move the pinion stop collar down to the starter clutch sub-assembly.

    6. A01LWZ4C02
      *1 Snap Ring
      *2 Pinion Stop Collar

      Using a screwdriver, remove the snap ring.

    7. Remove the pinion stop collar.

    8. A01LVV6C02
      *1 Starter Clutch Sub-assembly
      *2 Planet Carrier Shaft Sub-assembly

      Remove the starter clutch sub-assembly from the planet carrier shaft sub-assembly.

  6. REMOVE PLANET CARRIER SHAFT SUB-ASSEMBLY


    1. A01LXEZ

      Using 2 screwdrivers, remove the snap ring from the planet carrier shaft sub-assembly.

    2. A01LX1R

      Remove the washer from the planet carrier shaft sub-assembly.

    3. A01LYQ8C03
      *1 Planet Carrier
      *2 Planet Carrier Shaft Sub-assembly

      Remove the planet carrier shaft sub-assembly from the planet carrier.

    4. A01LX82C01
      *1 Damper Rubber
      *2 Planet Carrier
      *3 Intermediate Sealing

      Remove the intermediate sealing and 3 damper rubbers from the planet carrier.