OIL PUMP INSTALLATION

PROCEDURE


  1. INSTALL OIL PUMP ASSEMBLY


    1. Install the oil pump with the 3 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  2. INSTALL NO. 2 OIL PAN SUB-ASSEMBLY


    1. A01KD3MC03
      *1 Seal Packing
      *a 3.0 to 4.5 mm (0.118 to 0.177 in.)
      *b 6.0 mm (0.236 in.)

      Remove any old packing material and be careful not to drop any oil on the contact surfaces of the stiffening crankcase and No. 2 oil pan sub-assembly.

    2. Apply seal packing in a continuous line as shown in the illustration.

      Application Specification
      Area Seal Packing Diameter Distance from Center of Bolt Hole to Center of Seal Packing
      A - A 3.0 to 4.5 mm (0.118 to 0.177 in.) 6.0 mm (0.236 in.)
      B - B -
      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent

      Note


      • Remove any oil from the contact surfaces.

      • Install the No. 2 oil pan sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

      • Do not add engine oil for at least 2 hours after installing the No. 2 oil pan sub-assembly.

    3. Install the No. 2 oil pan with the 10 bolts and 2 nuts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  3. INSTALL NO. 2 CHAIN SUB-ASSEMBLY


    1. Temporarily install the crankshaft pulley bolt.

    2. A01KC32

      Set the crankshaft key as shown in the illustration.

    3. Turn the drive shaft so that the cutout faces upward.

    4. Remove the crankshaft pulley bolt.

    5. A01KC0TC01
      *1 Timing Mark
      *2 Mark Plate (Yellow)
      *3 Oil Pump Drive Gear
      *4 Oil Pump Drive Shaft Gear
      A01KBXM Front

      Align the yellow mark plates with the timing mark of each gear as shown in the illustration.

    6. Install the gears onto the crankshaft and oil pump shaft with the chain on the gears.

    7. Temporarily install the oil pump drive shaft gear with the nut.

    8. Install the chain damper spring to the chain tensioner plate, and then install the chain tensioner plate with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    9. Temporarily install the crankshaft pulley with the pulley bolt.

    10. A01KCG4E01

      Using SST, hold the crankshaft. Then tighten the drive shaft gear nut.

      for 86 mm (3.39 in.) Bolt Pitch Type:

      SST
      09213-58014   ( 91551-80840 )
      09330-00021

      for 64 mm (2.52 in.) Bolt Pitch Type:

      SST
      09213-54015
      Torque:
      28 N*m  { 286 kgf*cm, 21 ft.*lbf }

      Tech Tips

      For the 64 mm (2.52 in.) bolt pitch type, the part number of the installationbolt for SST (crankshaft pulley holding tool) is 91551-00850 (quantity: 2).

    11. Remove SST, the crankshaft pulley bolt and the crankshaft pulley.

  4. INSTALL CRANKSHAFT TIMING SPROCKET


    1. A01KBM6C02
      *a Front

      Install the crankshaft timing sprocket as shown in the illustration.

  5. SET NO. 1 CYLINDER TO TDC/COMPRESSION

    Click here

  6. INSTALL NO. 1 CHAIN VIBRATION DAMPER

    Click here

  7. INSTALL CHAIN SUB-ASSEMBLY

    Click here

  8. INSTALL CHAIN TENSIONER SLIPPER

    Click here

  9. INSTALL NO. 2 CHAIN VIBRATION DAMPER


    1. Install the No. 2 chain vibration damper with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

  10. CHECK NO. 1 CYLINDER TO TDC/COMPRESSION

    Click here

  11. INSTALL TIMING CHAIN COVER SUB-ASSEMBLY


    1. Install a new gasket.

      Note

      Remove any oil from the contact surface.

    2. Install the engine water pump assembly with the 3 bolts.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    3. Remove any old packing (FIPG) material and be careful not to drop any oil on the contact surfaces of the timing chain cover sub-assembly, cylinder head, camshaft housing, stiffening crankcase and cylinder block.

      A01KBUXC01
      A01KCAQ Clean and Degrease - -

    4. Install 3 new O-rings.

    5. Apply seal packing as shown in the illustration.

      A01KDG8C01
      *a 5.0 mm (0.197 in.) - -
      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Standard seal diameter
      5.0 mm (0.197 in.)

      Note


      • Remove any oil from the contact surface.

      • Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

      • Do not add engine oil for at least 2 hours after installing the timing chain cover sub-assembly.

    6. Apply seal packing to the timing chain cover sub-assembly in a continuous line as shown in the following illustration.

      A01KBLLC01
      *a 2.5 mm (0.0984 in.) *b 2.5 to 3.5 mm (0.0984 to 0.138 in.)
      *c 5.0 mm (0.197 in.) *d 4.5 to 5.5 mm (0.177 to 0.217 in.)
      *e 7.5 mm (0.295 in.) *f 7.0 to 8.0 mm (0.276 to 0.315 in.)
      Seal Packing
      Item Seal Packing
      Dashed line Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Continuous line
      Alternate long and short dashed line Toyota Genuine Seal Packing 1282B, Three Bond 1282B or equivalent
      Application Specification
      Area Seal Packing Diameter Distance from Edge of Cover to: Seal Packing Application Length Distance from Top of Cover to Top of Seal Packing
      Dashed line 2.5 to 3.5 mm (0.0984 to 0.138 in.)

      Center of seal packing

      2.5 mm (0.0984 in.)

      		 - -
      Continuous line 4.5 to 5.5 mm (0.177 to 0.217 in.) or 7.0 to 8.0 mm (0.276 to 0.315 in.) - - -
      Alternate long and short dashed line 4.0 mm (0.157 in.)

      Center of seal packing

      3.0 mm (0.118 in.)

      		 - -
      A - A 2.5 to 3.5 mm (0.0984 to 0.138 in.)

      Center of seal packing

      2.5 mm (0.0984 in.)

      		 - -
      B - B 4.5 to 5.5 mm (0.177 to 0.217 in.)

      Opposite edge of seal packing

      5.0 mm (0.197 in.)

      		 - -
      C - C 7.0 to 8.0 mm (0.276 to 0.315 in.)

      Opposite edge of seal packing

      7.5 mm (0.295 in.)

      		 - -
      F 4.5 to 5.5 mm (0.177 to 0.217 in.) - 15.8 mm (0.622 in.) 50.1 mm (1.97 in.)
      G 4.5 to 5.5 mm (0.177 to 0.217 in.) - 10.3 mm (0.406 in.) 155.1 mm (6.11 in.)
      H 7.0 to 8.0 mm (0.276 to 0.315 in.) - 19.5 mm (0.768 in.) 165.4 mm (6.51 in.)
      I 4.5 to 5.5 mm (0.177 to 0.217 in.) - 14.6 mm (0.575 in.) 397.8 mm (1.31 ft.)
      J 4.5 to 5.5 mm (0.177 to 0.217 in.) - 18.6 mm (0.732 in.) 51.4 mm (2.02 in.)
      K 4.5 to 5.5 mm (0.177 to 0.217 in.) - 25.3 mm (0.996 in.) 133.9 mm (5.27 in.)
      L 7.0 to 8.0 mm (0.276 to 0.315 in.) - 25.8 mm (1.02 in.) 159.2 mm (6.28 in.)
      M 4.5 to 5.5 mm (0.177 to 0.217 in.) - 5.0 mm (0.197 in.) 185.0 mm (7.28 in.)
      N 4.5 to 5.5 mm (0.177 to 0.217 in.) - 14.6 mm (0.575 in.) 397.8 mm (1.31 ft.)
      O 4.0 mm (0.157 in.)

      Center of seal packing

      3.0 mm (0.118 in.)

      		 - -

      Note


      • When the contact surfaces are wet, wipe them with oil-free cloth before applying seal packing.

      • Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

      • After applying seal packing to the timing chain cover sub-assembly, install the engine mounting bracket and oil filter bracket within 10 minutes.

      • Do not add engine oil for at least 2 hours after installation.

    7. Clean the bolts and their installation holes.

    8. Install the timing chain cover.

    9. Temporarily install the engine mounting bracket with the 3 bolts.

      Note


      • Install the mounting bracket within 10 minutes after installing the timing chain cover sub-assembly.

      • Do not add engine oil for at least 2 hours after installation.

    10. Install 2 new O-rings.

    11. Temporarily install the oil filter bracket with the 4 bolts.

      Note


      • Install the oil filter bracket within 10 minutes after installing the timing chain cover sub-assembly.

      • Do not add engine oil for at least 2 hours after installation.

    12. Apply adhesive to 5 and a half threads or more of the end of bolt E.

      Adhesive
      Toyota Genuine Adhesive 1324, Three Bond 1324 or equivalent

    13. Install the timing chain cover with the 26 bolts and seal washer in the order shown in the illustration.

      A01KBV8C01
      *1 Seal Washer - -
      *a Torque Specification *b Bolt Tightening Order
      Torque:
      for bolt A, E
      25.5 N*m  { 260 kgf*cm, 19 ft.*lbf }
      for bolt B
      51 N*m  { 520 kgf*cm, 38 ft.*lbf }
      for bolt C
      51 N*m  { 520 kgf*cm, 38 ft.*lbf }
      for bolt D
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

      Note


      • When the contact surfaces are wet, wipe them with oil-free cloth before applying seal packing.

      • Install the timing chain cover sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying the seal packing.

      • Do not add engine oil for at least 2 hours after installation.

      Bolt Length
      Item Length Thread Diameter
      Bolt A, E 35 mm (1.38 in.) 8 mm (0.315 in.)
      Bolt B 55 mm (2.17 in.) 10 mm (0.394 in.)
      Bolt C 80 mm (3.15 in.) 10 mm (0.394 in.)
      Bolt D 40 mm (1.57 in.) 6 mm (0.236 in.)

      Tech Tips

      Apply adhesive to bolt E before installing it.

  12. INSTALL OIL FILTER CAP ASSEMBLY

    Click here

  13. INSTALL TIMING CHAIN COVER OIL SEAL

    Click here

  14. INSTALL ENGINE MOUNTING BRACKET STUD BOLT

    Click here

  15. INSTALL CRANKSHAFT PULLEY

    Click here

  16. INSTALL NO. 1 CHAIN TENSIONER ASSEMBLY

    Click here

  17. INSTALL CYLINDER HEAD COVER GASKET

    Click here

  18. INSTALL CYLINDER HEAD COVER SUB-ASSEMBLY

    Click here

  19. INSTALL THERMOSTAT

    Click here

  20. INSTALL WATER INLET

    Click here

  21. CONNECT WATER INLET HOSE

    Click here

  22. INSTALL WATER BY-PASS HOSE

    Click here

  23. INSTALL NO. 1 WATER BY-PASS PIPE

    Click here

  24. INSTALL NO. 3 WATER BY-PASS HOSE

    Click here

  25. INSTALL PCV HOSE

    Click here

  26. INSTALL EXHAUST MANIFOLD

    Click here

  27. INSTALL MANIFOLD STAY

    Click here

  28. INSTALL NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

    Click here

  29. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE

    Click here

  30. INSTALL IGNITION COIL ASSEMBLY

    Click here

  31. INSTALL FUEL INJECTOR ASSEMBLY

    Click here

  32. INSTALL FUEL DELIVERY PIPE SUB-ASSEMBLY

    Click here

  33. INSTALL FUEL TUBE SUB-ASSEMBLY

    Click here

  34. INSTALL INTAKE MANIFOLD

    Click here

  35. INSTALL VACUUM SURGE TANK

    Click here

  36. INSTALL THROTTLE BODY ASSEMBLY

    Click here

  37. REMOVE ENGINE STAND

    Click here

  38. INSTALL ENGINE ASSEMBLY WITH TRANSAXLE

    Click here