OIL PUMP REMOVAL

PROCEDURE

REMOVE ENGINE ASSEMBLY WITH TRANSAXLE

Click here
INSTALL ENGINE TO ENGINE STAND

Click here
REMOVE THROTTLE BODY ASSEMBLY

Click here
REMOVE VACUUM SURGE TANK

Click here
REMOVE INTAKE MANIFOLD

Click here
REMOVE FUEL TUBE SUB-ASSEMBLY

Click here
REMOVE FUEL DELIVERY PIPE SUB-ASSEMBLY

Click here
REMOVE FUEL INJECTOR ASSEMBLY

Click here
REMOVE IGNITION COIL ASSEMBLY

Click here
REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

Click here
REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

Click here
REMOVE MANIFOLD STAY

Click here
REMOVE EXHAUST MANIFOLD

Click here
REMOVE PCV HOSE

Click here
DISCONNECT NO. 3 WATER BY-PASS HOSE

Click here
REMOVE NO. 1 WATER BY-PASS PIPE

Click here
REMOVE WATER BY-PASS HOSE

Click here
DISCONNECT WATER INLET HOSE

Click here
REMOVE WATER INLET

Click here
REMOVE THERMOSTAT

Click here
REMOVE CYLINDER HEAD COVER SUB-ASSEMBLY

Click here
REMOVE CYLINDER HEAD COVER GASKET

Click here
SET NO. 1 CYLINDER TO TDC/COMPRESSION

Click here
REMOVE CRANKSHAFT PULLEY

Click here
REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY

Click here
REMOVE OIL FILTER CAP ASSEMBLY

Click here
REMOVE ENGINE MOUNTING BRACKET STUD BOLT

Click here
REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
1. Remove the 3 bolts and engine mounting bracket RH.
2. Remove the 4 bolts and oil filter bracket.
3. Remove the 2 O-rings.
4. *1 Seal Washer
  
  Remove the 19 bolts and seal washer.
5. *1 Protective Tape
  
  Remove the timing chain cover sub-assembly by prying between the timing chain cover sub-assembly and cylinder head, camshaft housing, cylinder block and stiffening crankcase with a screwdriver as shown in the illustration.
  
  Note
  
  Be careful not to damage the contact surfaces of the cylinder head, camshaft housing, cylinder block, stiffening crankcase and timing chain cover sub-assembly.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
6. Remove the 3 O-rings.
7. Remove the 3 bolts and engine water pump assembly.
8. Remove the gasket.
REMOVE TIMING CHAIN COVER OIL SEAL
1. *1 Protective Tape
  
  *2 Wooden Block
  
  Place the timing chain cover on wooden blocks.
2. Using a screwdriver, tap out the timing chain cover oil seal.
  
  Note
  
  Do not damage the surface of the oil seal press fit hole.
  
  Tech Tips
  
  Tape the screwdriver tip before use.
REMOVE CHAIN TENSIONER SLIPPER

Click here
REMOVE NO. 1 CHAIN VIBRATION DAMPER

Click here
REMOVE NO. 2 CHAIN VIBRATION DAMPER
1. Remove the 2 bolts and No. 2 chain vibration damper.
REMOVE CHAIN SUB-ASSEMBLY

Click here
REMOVE CRANKSHAFT TIMING SPROCKET
1. Remove the crankshaft timing sprocket.

REMOVE NO. 2 CHAIN SUB-ASSEMBLY

Temporarily install the crankshaft pulley and crankshaft pulley bolt.
Using SST, hold the crankshaft. Then remove the drive shaft gear nut.

for 86 mm (3.39 in.) Bolt Pitch Type:

SST

09213-58014 ( 91551-80840 )

09330-00021

for 64 mm (2.52 in.) Bolt Pitch Type:

SST

09213-54015

Tech Tips

For the 64 mm (2.52 in.) bolt pitch type, the part number of the installationbolt for SST (crankshaft pulley holding tool) is 91551-00850 (quantity: 2).
Remove SST, the crankshaft pulley bolt and the crankshaft pulley.
Remove the bolt, chain tensioner plate and chain damper spring.

*1	Oil Pump Drive Gear
*2	Oil Pump Drive Shaft Gear
*3	No. 2 Chain Sub-assembly

Remove the oil pump drive gear, oil pump drive shaft gear and No. 2 chain.

REMOVE NO. 2 OIL PAN SUB-ASSEMBLY
1. Remove the 10 bolts and 2 nuts.
2. Insert the blade of an oil pan seal cutter between the stiffening crankcase and No. 2 oil pan sub-assembly. Cut through the sealer and remove the No. 2 oil pan sub-assembly.
  Note
  
  Be careful not to damage the surface of the No. 2 oil pan sub-assembly which contacts the stiffening crankcase.
  
  Be careful not to damage the stiffening crankcase flange.
REMOVE OIL PUMP ASSEMBLY
1. Remove the 3 bolts and oil pump assembly.

*1	Protective Tape
*2	Wooden Block