OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or waterless hand cleaner thoroughly to remove any used engine oil. Do not use gasoline, thinners or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap.

    2. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    3. Clean and install a new gasket and the oil pan drain plug.

      Torque:
      40 N*m  { 408 kgf*cm, 30 ft.*lbf }

  2. REMOVE OIL FILTER CAP ASSEMBLY


    1. A00YVBHC01
      *1 Pipe
      *2 Hose

      Connect a hose with an inner diameter of 15 mm (0.591 in.) to the pipe.

    2. A00YX23

      Remove the oil filter drain plug.

    3. A00YSO4C01
      *1 Oil Filter Cap
      *2 Valve
      *3 Pipe
      *4 O-Ring

      Install the pipe to the oil filter cap.

      Note

      If the O-ring is removed with the drain plug, install the O-ring together with the pipe.

      Tech Tips

      Use a container to catch the draining oil.

    4. A00YWI9

      Check that the oil is drained from the oil filter. Then disconnect the pipe as shown in the illustration and remove the O-ring.

    5. A00YTATC04
      *1 Oil Filter Bracket Clip

      Using SST, remove the oil filter cap.

      SST
      09228-06501

      Note

      Do not remove the oil filter bracket clip.

    6. A00YVYCC01
      *1 Oil Filter Element
      *2 O-Ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Be sure to remove the O-ring (for the cap) by hand, without using any tools, to prevent damage to the groove for the O-ring in the cap.

  3. INSTALL OIL FILTER CAP ASSEMBLY


    1. Clean the inside of the oil filter cap, the threads and O-ring groove.

    2. A00YWBUC10
      *1 O-Ring
      *a CORRECT
      *b INCORRECT

      Apply a light coat of engine oil to a new O-ring for the cap, and then install the O-ring to the groove of the oil filter cap.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element into the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    6. A00YRCYC01
      *1 Oil Filter Cap
      *2 O-Ring
      *3 Stiffening Crankcase
      *a No Gap

      Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note

      After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

    7. Apply a small amount of engine oil to a new drain plug O-ring and install the O-ring to the oil filter cap.

      Note

      Before installing the O-ring, remove any dirt or foreign matter from the installation surface of the oil filter cap.

    8. A00YVHAC01
      *1 O-Ring

      Install the oil filter drain plug.

      Torque:
      12.5 N*m  { 127 kgf*cm, 9 ft.*lbf }

      Note

      Make sure that the O-ring does not get caught between any surrounding parts.

  4. ADD ENGINE OIL


    1. Add new engine oil and install the oil filler cap.

      Standard Oil Grade
      Oil Grade Oil Viscosity
      API grade SL "energy-conserving", SM "energy-conserving", SN "resource-conserving" or ILSAC multigrade engine oil

      0W-20

      5W-20

      5W-30

      10W-30
      API grade SL, SM or SN multigrade engine oil

      15W-40

      20W-50
      Standard Capacity
      Item Specified Condition
      Drain and refill without oil filter change 4.0 liters (4.2 US qts, 3.5 Imp. qts)
      Drain and refill with oil filter change 4.4 liters (4.6 US qts, 3.9 Imp. qts)
      Dry fill 5.3 liters (5.6 US qts, 4.7 Imp. qts)

  5. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  6. INSPECT ENGINE OIL LEVEL

    Click here