OIL AND OIL FILTER REPLACEMENT

CAUTION / NOTICE / HINT

CAUTION:


  • Prolonged and repeated contact with engine oil will result in the removal of natural oils from the skin, leading to dryness, irritation and dermatitis. In addition, used engine oil contains potentially harmful contaminants which may cause skin cancer.

  • Precautions should be taken when replacing engine oil to minimize the risk of your skin making contact with used engine oil. Protective clothing and gloves that cannot be penetrated by oil should be worn. The skin should be washed with soap and water, or use waterless hand cleaner, to remove any used engine oil thoroughly. Do not use gasoline, thinners or solvents.

  • In order to protect the environment, used oil and used oil filters must be disposed of at designated disposal sites.

PROCEDURE


  1. DRAIN ENGINE OIL


    1. Remove the oil filler cap sub-assembly.

    2. Remove the clip and open the oil pan drain service cover.

    3. Remove the oil pan drain plug and gasket, and then drain the engine oil into a container.

    4. Install a new gasket and the oil pan drain plug.

      Torque:
      38 N*m  { 387 kgf*cm, 28 ft.*lbf }

    5. Close the oil pan drain service cover and install the clip.

  2. REMOVE OIL FILTER ELEMENT


    1. A00YWQFC01
      *1 Oil Filter Drain Pipe
      *2 Hose

      Connect a hose with an inside diameter of 15 mm (0.591 in.) to the oil filter drain pipe.

    2. Remove the clip and open the oil filter element service cover.

    3. A00YU7T

      Remove the oil filter drain plug.

    4. Remove the O-ring from the oil filter drain plug and install it to an oil filter drain pipe.

    5. A00YW24C01
      *1 Oil Filter Cap
      *2 O-Ring
      *3 Oil Filter Drain Pipe

      Install the oil filter drain pipe to the oil filter cap and drain the engine oil into a container.

    6. Remove the oil filter drain pipe.

    7. Apply a light coat of engine oil to a new O-ring and install the O-ring to the oil filter drain plug.

    8. Install the oil filter drain plug to the oil filter cap.

      Torque:
      13 N*m  { 127 kgf*cm, 9 ft.*lbf }
    9. A00YS8EC01

      Using SST, remove the oil filter cap.

      SST
      09228-06501
    10. A00YT7NC01
      *1 Oil Filter Element
      *2 O-Ring

      Remove the oil filter element and O-ring from the oil filter cap.

      Note

      Be sure to remove the cap O-ring by hand without using any tools to prevent damage to the oil filter cap O-ring groove.

  3. INSTALL OIL FILTER ELEMENT


    1. Clean the inside of the oil filter cap, its threads and its O-ring groove.

    2. A00YWBUC06
      *1 O-Ring
      *a CORRECT
      *b INCORRECT

      Apply a small amount of engine oil to a new O-ring and install the O-ring to the oil filter cap.

      Note


      • Be sure to install the O-ring in the proper location, otherwise oil may leak.

      • Do not twist the O-ring.

    3. Set a new oil filter element in the oil filter cap.

    4. Remove any dirt or foreign matter from the installation surface of the engine.

    5. Apply a small amount of engine oil to the O-ring again and temporarily install the oil filter cap.

    6. Check and clean the oil filter installation surface.

    7. A00YUQUC01
      *1 Oil Filter Cap
      *2 O-Ring
      *3 Oil Filter Bracket
      *a No Gap

      Using SST, tighten the oil filter cap.

      SST
      09228-06501
      Torque:
      25 N*m  { 255 kgf*cm, 18 ft.*lbf }

      Note

      After tightening the oil filter cap, make sure that there is no gap and that the O-ring is not protruding.

    8. Close the oil filter element service cover and install the clip.

  4. ADD ENGINE OIL


    1. Add new engine oil.

      Standard Oil Grade
      Oil Grade Oil Viscosity (SAE)
      ACEA C2

      - 0W-30

      - 5W-30
      Standard Capacity
      Item Specified Condition
      Drain and refill without oil filter change 5.5 liters (5.8 US qts, 4.8 Imp. qts)
      Drain and refill with oil filter change 5.9 liters (6.2 US qts, 5.2 Imp. qts)
      Dry fill 6.3 liters (6.7 US qts, 5.5 Imp. qts)

  5. INSPECT FOR OIL LEAK


    1. Start the engine. Make sure that there are no oil leaks from the areas that were worked on.

  6. INSPECT ENGINE OIL LEVEL

    Click here