AUTOMATIC TRANSAXLE SYSTEM, Diagnostic DTC:P0798

DTC Code DTC Name
P0798 Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3)

DESCRIPTION

Changing from 1st to 6th is performed by the TCM turning shift solenoid valves SL1, SL2, SL3, SL4 and SL on and off. If an open or short circuit occurs in any of the shift solenoid valves, the TCM controls the remaining normal shift solenoid valves to allow the vehicle to be operated.

Click here

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0798 Pressure Control Solenoid "C" Electrical (Shift Solenoid Valve SL3) An open or short circuit (output signal duty is 0% or 100%) is detected by the TCM in the shift solenoid valve SL3 circuit while driving and shifting gears (SL3 output signal duty is more than 0% and less than 100% under normal conditions) (1-trip detection logic).

  • Open or short in shift solenoid valve SL3 circuit

  • Shift solenoid valve SL3

  • TCM

 Comes on DTC stored

MONITOR DESCRIPTION

The TCM commands gear shifts by turning the shift solenoid valves on or off. When there is an open or short circuit in any shift solenoid valve circuit, the TCM detects the problem and illuminates the MIL and stores the DTC. And the TCM performs the fail-safe function and turns the other normal shift solenoid valves on or off. (In case of an open or short circuit, the TCM stops sending current to the circuit.)

Click here

WIRING DIAGRAM

A01QQAOE03
*a Shift Solenoid Valve SL3
*b Transmission Valve Body Assembly
*c Transmission Wire
*d Automatic Transaxle Assembly

CAUTION / NOTICE / HINT

Note

Perform registration and/or initialization when parts related to the automatic transaxle are replaced.

Click here

Tech Tips

The following table shows normal operation of shift solenoid valve SL3 when the shift lever is in D:

TCM gear shift command 1st 2nd 3rd 4th 5th 6th
Shift solenoid valve SL3 OFF ON OFF OFF OFF ON

PROCEDURE


  1. INSPECT TRANSMISSION WIRE (SHIFT SOLENOID VALVE SL3)


    1. A01QOXMC17
      *a

      Component without TCM connected

      (Transmission Wire)

      Remove the TCM.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      16 (SL3+) - 15 (SL3-) 20°C (68°F) 5.0 to 5.6 Ω
      16 (SL3+) - Body ground Always 10 kΩ or higher
      15 (SL3-) - Body ground Always 10 kΩ or higher
      16 (SL3+) - All other terminals except 15 (SL3-) Always 10 kΩ or higher
      15 (SL3-) - All other terminals except 16 (SL3+) Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TCM Click here

    NG

  2. INSPECT SHIFT SOLENOID VALVE SL3


    1. A01QTPTC16
      *1 Shift Solenoid Valve SL3

      Remove shift solenoid valve SL3.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      1 - 2 20°C (68°F) 5.0 to 5.6 Ω

    3. Apply 12 V battery voltage to the shift solenoid valve and check that the valve moves and makes an operating noise.

      OK
      Measurement Condition Specified Condition

      • Battery positive (+) with a 21 W bulb → Terminal 1

      • Battery negative (-) → Terminal 2

      		 Valve moves and makes an operating noise
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE TRANSMISSION WIRE Click here

    NG

    REPLACE SHIFT SOLENOID VALVE SL3 Click here