INTAKE MANIFOLD INSTALLATION

PROCEDURE


  1. INSTALL INTAKE AIR CONTROL VALVE ACTUATOR (for TCV)

    Click here

  2. INSTALL PURGE LINE HOSE


    1. Install the purge line hose to the intake manifold, and slide the clamp to secure it.

    2. Connect the purge line hose to the clamp.

  3. INSTALL CHECK VALVE


    1. Install the 2 vacuum hoses to the check valve.

    2. Connect the 2 vacuum hoses to the intake manifold to install the check valve.

    3. A00YVCIC02
      *1 Black

      Check that the check valve is installed as shown in the illustration.

  4. INSTALL UNION TO CONNECTOR TUBE HOSE


    1. Install the union to connector tube hose to the intake manifold, and slide the clamp to secure it.

  5. INSTALL INTAKE MANIFOLD


    1. Install the 2 vacuum hoses to the intake manifold.

    2. A00YUYAC01
      *a Condition: Closed

      for TCV:

      Close the tumble control valves.

      Note

      The valves may be damaged if they are not closed before installing the intake manifold.

      Tech Tips

      Connect the battery to the terminals of the actuator and operate the motor to close the valves.

      Click here

    3. A00YXV0

      Install a new gasket to the intake manifold.

    4. A00YXXPN01

      Install the intake manifold with the 6 bolts and tighten the bolts in the sequence shown in the illustration.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

  6. CONNECT NO. 2 PCV HOSE


    1. Connect the No. 2 PCV hose to the intake manifold, and slide the clamp to secure it.

  7. CONNECT WIRE HARNESS


    1. Attach the clamp and connect the wire harness.

    2. Install the bracket with the bolt.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    3. for TCV:

      Connect the intake air control actuator connector.

    4. Install the wire harness clamp bracket with the 2 bolts.

      Torque:
      10 N*m  { 102 kgf*cm, 7 ft.*lbf }

    5. Attach the 2 clamps.

    6. Connect the 2 vacuum hoses and connector and attach the clamp to the vacuum switching valve.

  8. CONNECT HEATER HOSE


    1. Connect the outlet heater water hose to the heater radiator unit, and slide the clamp to secure the hose.

    2. Connect the inlet heater water hose to the heater radiator unit, and slide the clamp to secure the hose.

  9. INSTALL NO. 1 HOSE TO HOSE TUBE


    1. Install the No. 1 hose to hose tube with the 2 nuts.

      Torque:
      5.4 N*m  { 55 kgf*cm, 48 in.*lbf }

    2. Connect the 2 hoses, and slide the 2 clamps to secure the hoses.

  10. INSTALL OUTER COWL TOP PANEL SUB-ASSEMBLY


    1. Install the outer cowl top panel sub-assembly with the 13 bolts.

      Torque:
      7.0 N*m  { 71 kgf*cm, 62 in.*lbf }

    2. Attach the clamp to the outer cowl top panel sub-assembly.

  11. INSTALL WINDSHIELD WIPER MOTOR ASSEMBLY

    Click here

  12. INSTALL THROTTLE WITH MOTOR BODY ASSEMBLY

    Click here

  13. INSTALL FUEL DELIVERY PIPE

    Click here

  14. ADD ENGINE COOLANT

    Click here

  15. INSPECT FOR COOLANT LEAK

    Click here