INTAKE MANIFOLD INSTALLATION

CAUTION / NOTICE / HINT

Note


  • When replacing the injectors (including shuffling the injectors between the cylinders), common rail, intake manifold or cylinder head, it is necessary to replace the injection pipes with new ones.

  • When replacing the fuel supply pump, common rail, intake manifold or cylinder head, it is necessary to replace the fuel inlet pipe with a new one.

PROCEDURE


  1. INSTALL STUD BOLT

    Tech Tips

    If a stud bolt is deformed or the threads are damaged, replace it.


    1. A01VAO4C01
      *a 35 mm (1.38 in.)
      *b 20 mm (0.787 in.)
      *c 13 mm (0.512 in.)

      Using an E8 "TORX" wrench, install the 2 stud bolts.

      Torque:
      9.0 N*m  { 92 kgf*cm, 80 in.*lbf }

  2. INSTALL INTAKE MANIFOLD


    1. Install a new gasket to the cylinder head sub-assembly.

      Tech Tips

      Install the gasket with the part labeled A facing the right side of the vehicle as shown in the illustration.

      A01VB37N01
    2. A01VAXIC01
      *1 Nut

      Install the intake manifold with the 7 bolts and 2 nuts.

      Torque:
      23 N*m  { 235 kgf*cm, 17 ft.*lbf }
      Bolt Length
      Item Length
      Bolt A 90 mm (3.54 in.)
      Bolt B 25 mm (0.984 in.)

  3. CONNECT NO. 2 VACUUM TRANSMITTING HOSE ASSEMBLY


    1. Connect the No. 2 vacuum transmitting hose assembly to the intake manifold, and slide the clamp to secure the hose.

  4. INSTALL NO. 2 INTAKE MANIFOLD


    1. Install a new gasket and the No. 2 intake manifold with the bolt and 2 nuts.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

  5. INSTALL ENGINE COVER BRACKET


    1. Install the engine cover bracket with the bolt.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  6. INSTALL GAS FILTER BRACKET


    1. Install the gas filter bracket with the 2 bolts.

      Torque:
      8.8 N*m  { 90 kgf*cm, 78 in.*lbf }

  7. INSTALL NO. 1 GAS FILTER


    1. A01VANZC01
      *1 Protrusion
      *2 Groove

      Install the No. 1 gas filter to the gas filter bracket.

      Note

      Make sure the protrusion of the No. 1 gas filter is aligned with the groove of the gas filter bracket.

    2. Connect the vacuum hose.

  8. INSTALL DIESEL TURBO PRESSURE SENSOR

    Click here

  9. INSTALL ENGINE OIL LEVEL DIPSTICK GUIDE


    1. Install a new O-ring to the engine oil level dipstick guide.

    2. Install the engine oil level dipstick guide with the 2 bolts.

      Torque:
      24 N*m  { 245 kgf*cm, 18 ft.*lbf }

    3. Connect the connector and attach the wire harness clamp to the engine oil level dipstick guide.

    4. Install the engine oil level dipstick.

  10. INSTALL INTAKE MANIFOLD INSULATOR


    1. Install the intake manifold insulator to the intake manifold.

  11. INSTALL COMMON RAIL ASSEMBLY

    Click here

  12. INSTALL INJECTION PIPE SUB-ASSEMBLY

    Click here

  13. INSTALL FUEL INLET PIPE SUB-ASSEMBLY

    Click here

  14. INSTALL ELECTRIC EGR CONTROL VALVE ASSEMBLY

    Click here

  15. INSTALL NO. 2 EGR PIPE SUB-ASSEMBLY

    Click here

  16. CONNECT NO. 8 WATER BY-PASS HOSE

    Click here

  17. INSTALL NO. 7 WATER BY-PASS HOSE


    1. Install the No. 7 water by-pass hose to the electric EGR control valve assembly, and slide the clamp to secure the hose.

  18. INSTALL EGR VALVE BRACKET

    Click here

  19. CONNECT ENGINE WIRE

    Click here

  20. INSTALL DIESEL THROTTLE BODY ASSEMBLY

    Click here

  21. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  22. BLEED AIR FROM FUEL SYSTEM

    Click here

  23. INSPECT FOR FUEL LEAK

    Click here