FUEL TANK REMOVAL

PROCEDURE


  1. DISCHARGE FUEL SYSTEM PRESSURE

    Click here

  2. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  4. DRAIN FUEL

  5. DISCONNECT PARKING BRAKE CABLE


    1. A01VAVH

      Remove the 2 bolts and disconnect the parking brake cable.

  6. REMOVE FRONT FLOOR COVER


    1. A01VAZ6

      Remove the bolt and nut.

    2. Detach the 5 clips and remove the front floor cover.

  7. REMOVE NO. 1 FUEL TANK PROTECTOR


    1. A01VALS

      Detach the 3 clips and remove the nut and No. 1 fuel tank protector.

  8. REMOVE NO. 1 FLOOR UNDER COVER


    1. A01V723

      Detach the clip and remove the 2 nuts and No. 1 floor under cover.

  9. DISCONNECT NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    1. A01V9LS

      Slide the clamp and disconnect the No. 1 fuel evaporation tube sub-assembly.

  10. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. A01VA3B

      Disconnect the fuel tank main tube sub-assembly.

      Click here

  11. REMOVE FUEL HOSE PROTECTOR

    A01VA6N

    1. Detach the claw and remove the fuel hose protector from the fuel tank to filler pipe hose.

  12. DISCONNECT FUEL TANK TO FILLER PIPE HOSE


    1. A01V6UH

      Loosen the hose clamp and disconnect the fuel tank to filler pipe hose from the fuel tank assembly.

  13. DISCONNECT CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY


    1. A01V98Y

      Detach the hose clamp.

    2. A01V9ZG

      Slide the clamp and disconnect the charcoal canister outlet tube sub-assembly from the fuel tank breather tube.

  14. DISCONNECT NO. 3 FUEL TANK BREATHER TUBE SUB-ASSEMBLY


    1. A01V9IE

      Disconnect the No. 3 fuel tank breather tube sub-assembly from the fuel tank assembly.

      Click here

  15. REMOVE FUEL TANK ASSEMBLY


    1. A01V9W6

      Detach the 3 wire harness clamps.

    2. Using an engine lifter and attachments, support the fuel tank assembly.

    3. A01VAEE

      Remove the 2 bolts and No. 1 fuel tank band sub-assembly.

    4. Remove the 2 bolts and No. 1 fuel tank band sub-assembly LH.

    5. Remove the 2 bolts and No. 2 fuel tank band sub-assembly.

    6. Slightly lower the engine lifter.

      Note

      Be careful not to cut the wiring.

    7. A01V8MK

      Disconnect the fuel pump connector and sender gauge connector.

      Note


      • Before this procedure, check the connector for dirt, mud or other contamination.

      • Do not use any tools in this procedure.

    8. Detach the wire harness from the 3 clamps and remove the fuel tank assembly.

  16. DISCONNECT FUEL EMISSION HOSE

    Click here

  17. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

    Click here

  18. REMOVE FUEL TANK VENT TUBE SET PLATE

    Click here

  19. REMOVE FUEL SUCTION TUBE ASSEMBLY WITH PUMP

    Click here

  20. REMOVE FUEL SENDER GAUGE ASSEMBLY

    Click here

  21. REMOVE FUEL TANK MAIN TUBE SUB-ASSEMBLY

    A01V88U

    1. Detach the 5 clamps and remove the fuel tank main tube sub-assembly.

  22. REMOVE NO. 1 FUEL EVAPORATION TUBE SUB-ASSEMBLY


    1. Detach the 5 clamps and remove the No. 1 fuel evaporation tube sub-assembly.

  23. REMOVE NO. 3 FUEL TUBE CLAMP


    1. Remove the No. 3 fuel tube clamp from the fuel tank assembly.

  24. REMOVE NO. 5 FUEL TUBE CLAMP


    1. Remove the No. 5 fuel tube clamp from the fuel tank assembly.

  25. REMOVE FUEL TUBE GROMMET


    1. Remove the 3 fuel tube grommets from the fuel tank assembly.

  26. REMOVE CHARCOAL CANISTER OUTLET TUBE SUB-ASSEMBLY


    1. A01VAJD

      Detach the 2 clamps and remove the canister outlet tube sub-assembly from the fuel tank assembly.

  27. REMOVE FUEL EMISSION HOSE


    1. A01V7N8C01
      *1 Retainer

      Pinch the retainer as shown in the illustration, and then remove the fuel emission hose.

      Note


      • Clean off any dirt and foreign matter from the clip before disconnecting the hoses.

      • Do not use any tools in this procedure.

      • Do not forcefully bend or twist the nylon tube.

      • Put the hose in a plastic bag to prevent damage and contamination.

      • If the connector is stuck, pinch the retainer and push and pull the hose to disconnect it.