FUEL INJECTOR REMOVAL

CAUTION / NOTICE / HINT

Note


  • When replacing the injector assemblies (including shuffling the injector assemblies between the cylinders), common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the injection pipes with new ones.

  • When replacing the fuel supply pump assembly, common rail assembly, intake manifold or cylinder head sub-assembly, it is necessary to replace the fuel inlet pipe sub-assembly with a new one.

PROCEDURE


  1. PRECAUTION

    Note

    After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work.

    Click here

  2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

    Note

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  3. REMOVE NO. 1 ENGINE COVER

    Click here

  4. REMOVE AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  5. REMOVE AIR CLEANER FILTER ELEMENT SUB-ASSEMBLY

  6. REMOVE AIR CLEANER CASE

    Click here

  7. DISCONNECT ENGINE WIRE


    1. A01KDM7

      Remove the bolt from the wire harness bracket.

    2. A01KCUQ

      Disconnect the fuel temperature sensor connector and suction control valve connector.

    3. A01KD6Z

      Disconnect the engine coolant temperature sensor connector and turbocharger connector.

    4. A01KBGQ

      Detach the clamp and remove the bolt and fuel hose protector.

    5. A01KBDB

      Disconnect the exhaust fuel addition injector connector.

    6. A01KC76

      Disconnect the No. 1 vacuum switching valve connector and exhaust gas temperature sensor connector.

    7. A01KBA8

      Disconnect the 4 fuel injector connectors.

    8. A01KBXN

      Disconnect the glow plug connector.

    9. Disconnect the fuel pressure sensor connector and electric EGR control valve connector.

    10. A01KAT5

      Disconnect the diesel turbo pressure sensor connector.

    11. A01KDH1

      Disconnect the pressure discharge valve connector.

    12. A01KC5R

      Remove the 2 bolts and 5 nuts and disconnect the engine wire.

  8. REMOVE INJECTION PIPE SUB-ASSEMBLY

    Note

    After removing the injection pipe, cover the common rail with electrical tape to prevent dirt or foreign objects from entering the pipe inlet. Also, protect the injector inlets with electrical tape or plastic bags.


    1. A01KB1V

      Remove the 2 bolts and 4 No. 2 injection pipe clamps.

    2. A01KCQH

      Using a 14 mm union nut wrench, loosen the 8 union nuts and remove the 4 injection pipe sub-assemblies.

  9. REMOVE FUEL HOSE PROTECTOR

    Click here

  10. REMOVE FUEL TUBE SUB-ASSEMBLY

    Click here

  11. REMOVE NO. 2 NOZZLE LEAKAGE PIPE


    1. A01KD1O

      Slide the 3 clamps and disconnect the No. 2 fuel hose, No. 3 fuel hose and No. 4 fuel hose from the No. 2 nozzle leakage pipe.

    2. A01KBCVC02
      *1 Check Valve

      Remove the check valve and gasket.

    3. Remove the bolt and No. 2 nozzle leakage pipe.

  12. REMOVE NO. 1 NOZZLE LEAKAGE PIPE


    1. A01KDO4

      Remove the 4 union bolts and 4 gaskets.

    2. Remove the bolt and No. 1 nozzle leakage pipe.

  13. REMOVE NO. 1 NOZZLE HOLDER CLAMP


    1. A01KBBU

      Remove the 4 nozzle holder clamp bolts, 4 washers and 4 No. 1 nozzle holder clamps.

  14. REMOVE INJECTOR ASSEMBLY


    1. Remove the 4 injector assemblies and 4 injection nozzle seats from the cylinder head sub-assembly.

    2. Remove the O-ring from each injector assembly.

      Note

      When removing the injector assembly, store the injector assemblies in the correct order so that they can be returned to their original locations when reassembling.