CYLINDER HEAD REASSEMBLY

CAUTION / NOTICE / HINT

Tech Tips

Perform "Inspection After Repairs" after replacing the cylinder head sub-assembly.


PROCEDURE


  1. INSTALL CYLINDER HEAD STUD BOLT

    Note

    If a stud bolt is deformed or its threads are damaged, replace it.


    1. A01QOP3C03
      *a 18 mm (0.708 in.)
      *b 33 mm (1.30 in.)
      *c 13 mm (0.512 in.)

      Using an E7 "TORX" socket wrench, install the cylinder head stud bolts.

      Torque:
      6.5 N*m  { 66 kgf*cm, 58 in.*lbf }

  2. INSTALL NO. 1 STRAIGHT SCREW PLUG

    Note

    If coolant leaks from a straight screw plug or a plug is corroded, replace it.


    1. Using a 10 mm hexagon wrench, install 3 new gaskets and the 3 No. 1 straight screw plugs.

      Torque:
      44 N*m  { 449 kgf*cm, 32 ft.*lbf }

  3. INSTALL NO. 2 STRAIGHT SCREW PLUG

    Note

    If coolant leaks from a straight screw plug or a plug is corroded, replace it.


    1. Using a 14 mm hexagon wrench, install a new gasket and the No. 2 straight screw plug.

      Torque:
      78 N*m  { 795 kgf*cm, 58 ft.*lbf }

  4. INSTALL VALVE SPRING SEAT


    1. Install the valve spring seats to the cylinder head.

  5. INSTALL VALVE STEM OIL SEAL


    1. A01QPMTC06
      *1 Gray
      *2 Black
      *3 Mark "NOK"
      *a Intake Side
      *b Exhaust Side

      Apply a light coat of engine oil to new oil seals.

      Note

      Pay attention when installing the intake and exhaust oil seals. For example, installing the intake oil seal onto the exhaust side or installing the exhaust oil seal onto the intake side can cause installation problems later.

      Tech Tips

      The intake valve oil seals are gray and the exhaust valve oil seals are black.

    2. A01QPSDC05
      *a CORRECT
      *b INCORRECT

      Using SST, push in the intake and exhaust valve oil seals.

      SST
      09201-41020

      Note

      Failure to use SST will cause the seal to be damaged or improperly seated.

  6. INSTALL INTAKE VALVE


    1. A01QRP7C08
      *a 30 mm (1.18 in.) or more

      Apply plenty of engine oil to the tip area of the intake valve shown in the illustration.

    2. A01QTIFC06
      *a Narrow
      *b Wide

      Install the intake valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.

      Note

      Install the same parts in the same combination to their original locations.

    3. A01QRGIN01

      Using SST and wooden blocks, compress the inner compression spring and install the valve spring retainer locks.

      SST
      09202-70020

    4. Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

      Note

      Be careful not to damage the retainer.

  7. INSTALL EXHAUST VALVE


    1. A01QRP7C08
      *a 30 mm (1.18 in.) or more

      Apply plenty of engine oil to the tip area of the exhaust valve shown in the illustration.

    2. A01QUGSC05
      *a Narrow
      *b Wide

      Install the exhaust valve, inner compression spring and valve spring retainer to the cylinder head sub-assembly.

      Note

      Install the same parts in the same combination to their original locations.

    3. A01QOLZN01

      Using SST and wooden blocks, compress the inner compression spring and install the valve spring retainer locks.

      SST
      09202-70020

    4. Using a plastic-faced hammer, lightly tap the valve stem tip to ensure a proper fit.

      Note

      Be careful not to damage the retainer.