ENGINE ASSEMBLY COMPONENTS
ILLUSTRATION
| *A | for Half Cover Type | *B | for Full Cover Type |
| *C | w/ Canister Pump Module | - | - |
| *1 | BATTERY | *2 | BATTERY BRACKET REINFORCEMENT |
| *3 | BATTERY CLAMP SUB-ASSEMBLY | *4 | BATTERY INSULATOR |
| *5 | BATTERY TRAY | *6 | FRONT BATTERY BRACKET |
| *7 | FRONT FLOOR COVER | *8 | NO. 1 ENGINE COVER SUB-ASSEMBLY |
| *9 | NO. 1 ENGINE UNDER COVER | *10 | NO. 2 ENGINE UNDER COVER |
| *11 | RADIATOR RESERVOIR ASSEMBLY | *12 | REAR ENGINE UNDER COVER LH |
| *13 | REAR ENGINE UNDER COVER RH | - | - |
 |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *A | for Automatic Transaxle | *B | for Manual Transaxle |
| *1 | AIR CLEANER CAP SUB-ASSEMBLY | *2 | AIR CLEANER CASE |
| *3 | CLUTCH HOSE | *4 | DISCHARGE HOSE SUB-ASSEMBLY |
| *5 | ECM | *6 | FAN AND GENERATOR V BELT |
| *7 | GENERATOR ASSEMBLY | *8 | NO. 2 RADIATOR HOSE |
| *9 | RADIATOR HOSE SUB-ASSEMBLY | *10 | SUCTION HOSE SUB-ASSEMBLY |
| *11 | TRANSMISSION OIL COOLER | *12 | AIR CLEANER FILTER ELEMENT |
| *13 | ACCUMULATOR TO FLEXIBLE HOSE TUBE | *14 | CLIP |
| *15 | O-RING | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
 |
Compressor oil ND-OIL 8 or equivalent | - | - |
ILLUSTRATION
| *A | for Manual Transaxle | *B | for Automatic Transaxle |
| *1 | FUEL TUBE SUB-ASSEMBLY | *2 | VACUUM HOSE |
| *3 | HEATER HOSE | *4 | WIRE HARNESS |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *1 | FRONT AXLE SHAFT NUT LH | *2 | FRONT DRIVE SHAFT ASSEMBLY LH |
| *3 | FRONT LOWER NO. 1 SUSPENSION ARM SUB-ASSEMBLY LH | *4 | FRONT SPEED SENSOR LH |
| *5 | TIE ROD END SUB-ASSEMBLY LH | *6 | FRONT STABILIZER BAR |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
 |
Do not apply lubricants to the threads | - | - |
ILLUSTRATION
| *A | for Manual Transaxle | *B | for 4WD/AWD |
| *C | for 2WD | - | - |
| *1 | DRIVE SHAFT BEARING BRACKET | *2 | FRONT DRIVE SHAFT ASSEMBLY LH |
| *3 | FRONT DRIVE SHAFT ASSEMBLY RH | *4 | FRONT DRIVE SHAFT HOLE SNAP RING LH |
| *5 | DRIVE SHAFT BEARING HOLE SNAP RING | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| |
MP grease | |
Do not apply lubricants to the threads |
ILLUSTRATION
| *A | for Automatic Transaxle | *B | for 4WD/AWD |
| *C | for 2WD | - | - |
| *1 | DRIVE SHAFT BEARING BRACKET | *2 | FRONT DRIVE SHAFT ASSEMBLY LH |
| *3 | FRONT DRIVE SHAFT ASSEMBLY RH | *4 | FRONT DRIVE SHAFT HOLE SNAP RING LH |
| *5 | DRIVE SHAFT BEARING HOLE SNAP RING | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| |
MP grease | |
Do not apply lubricants to the threads |
ILLUSTRATION
| *A | for 4WD/AWD | *B | for Automatic Transaxle |
| *C | for Manual Transaxle | - | - |
| *1 | FRONT EXHAUST PIPE SUB-ASSEMBLY | *2 | FRONT NO. 2 EXHAUST PIPE SUB-ASSEMBLY |
| *3 | PROPELLER WITH CENTER BEARING SHAFT ASSEMBLY | *4 | TRANSMISSION CONTROL CABLE ASSEMBLY |
| *5 | ADJUSTING WASHER | *6 | CLIP |
| *7 | GASKET | *8 | COMPRESSION SPRING |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| |
Do not apply lubricants | - | - |
ILLUSTRATION
| *A | for Automatic Transaxle | - | - |
| *1 | COLUMN HOLE COVER SILENCER SHEET | *2 | ENGINE MOUNTING INSULATOR LH |
| *3 | ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH | *4 | ENGINE MOUNTING SPACER |
| *5 | FRONT SUSPENSION MEMBER REINFORCEMENT LH | *6 | FRONT SUSPENSION MEMBER REINFORCEMENT RH |
| *7 | NO. 2 STEERING INTERMEDIATE SHAFT ASSEMBLY | *8 | FRONT CROSSMEMBER SUB-ASSEMBLY |
| *9 | FRONT ENGINE MOUNTING INSULATOR | *10 | RADIATOR RESERVOIR BRACKET |
| *11 | WIRE HARNESS CLAMP BRACKET | *12 | FRONT SUSPENSION MEMBER BRACE REAR LH |
| *13 | FRONT SUSPENSION MEMBER BRACE REAR RH | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | - | - |
ILLUSTRATION
| *A | for Manual Transaxle | *B | for 2WD |
| *C | for 4WD/AWD | *D | for Automatic Transaxle |
| *1 | NO. 1 STEERING COLUMN HOLE COVER SUB-ASSEMBLY | *2 | REAR ENGINE MOUNTING INSULATOR |
| *3 | NO. 1 ENGINE HANGER | *4 | NO. 2 ENGINE HANGER |
| *5 | FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY | *6 | CLAMP |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
ILLUSTRATION
| *A | for Manual Transaxle | *B | for 4WD/AWD |
| *1 | CLUTCH COVER ASSEMBLY | *2 | CLUTCH DISC ASSEMBLY |
| *3 | CLUTCH RELEASE WITH BEARING CYLINDER ASSEMBLY | *4 | FLYWHEEL HOUSING UNDER COVER |
| *5 | FLYWHEEL SUB-ASSEMBLY | *6 | MANUAL TRANSAXLE ASSEMBLY |
| *7 | STARTER ASSEMBLY | *8 | TRANSFER ASSEMBLY |
| *9 | CLUTCH RELEASE CYLINDER TO BLEEDER TUBE | *10 | FRONT ENGINE MOUNTING BRACKET |
| *11 | CLUTCH TUBE BOOT | *12 | CLUTCH RELEASE BLEEDER SUB-ASSEMBLY |
| *13 | BLEEDER TO ACCUMULATOR TUBE | *14 | ACCUMULATOR TO FLEXIBLE HOSE TUBE |
| *15 | ENGINE MOUNTING BRACKET LH | *16 | REAR ENGINE MOUNTING BRACKET |
| *17 | CLUTCH ACCUMULATOR ASSEMBLY | - | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| |
Clutch spline grease | ★ | Precoated part |
| |
Do not apply lubricants to the threads | - | - |
ILLUSTRATION
| *A | for Automatic Transaxle | *B | for 4WD/AWD |
| *1 | AUTOMATIC TRANSAXLE ASSEMBLY | *2 | DRIVE PLATE AND RING GEAR SUB-ASSEMBLY |
| *3 | DRIVE PLATE AND TORQUE CONVERTER SETTING BOLT | *4 | FLYWHEEL HOUSING UNDER COVER |
| *5 | STARTER ASSEMBLY | *6 | TRANSFER ASSEMBLY |
| *7 | FRONT DRIVE PLATE SPACER | *8 | REAR DRIVE PLATE SPACER |
| *9 | ENGINE MOUNTING BRACKET LH | *10 | FRONT ENGINE MOUNTING BRACKET |
| *11 | REAR ENGINE MOUNTING BRACKET | - | - |
| *a | BLACK: x 1 SILVER: x 5 |
- | - |
| |
Specified torque: N*m (kgf*cm, ft.*lbf) | ● | Non-reusable part |
| ★ | Precoated part | |
Do not apply lubricants to the threads |