CAMSHAFT INSTALLATION

CAUTION / NOTICE / HINT

Tech Tips

Perform "Inspection After Repairs after replacing the camshaft No. 2 camshaft, camshaft timing gear assembly or camshaft timing exhaust gear assembly.

Click here

PROCEDURE


  1. INSTALL VALVE LASH ADJUSTER ASSEMBLY

    Click here

  2. INSTALL NO. 1 VALVE ROCKER ARM SUB-ASSEMBLY

    Click here

  3. INSTALL NO. 1 CAMSHAFT BEARING


    1. Clean the surfaces of bearings.

    2. Install the 2 No. 1 camshaft bearings.

    3. A01QPHWC03
      *1 Vernier Caliper

      Using a vernier caliper, measure the distance between the camshaft bearing cap edge and camshaft bearing edge.

      Dimension (A - B) or (B - A)
      0 to 0.7 mm (0 to 0.0276 in.)

      Note

      Position the bearings in the center of the camshaft bearing cap by measuring dimensions A and B.

  4. INSTALL NO. 2 CAMSHAFT BEARING


    1. Clean both surfaces of the bearings.

    2. Install the 2 No. 2 camshaft bearings.

    3. A01QR5BC01
      *1 Vernier Caliper

      Using a vernier caliper, measure the distance between the bearing cap edge and camshaft bearing edge.

      Dimension (A)
      1.05 to 1.75 mm (0.0413 to 0.0689 in.)

      Note

      Position the bearings in the center of the camshaft bearing cap by measuring dimension A.

  5. INSTALL NO. 2 CAMSHAFT

    Tech Tips

    Perform "Inspection After Repairs" after replacing the No. 2 camshaft.

    Click here


    1. Clean the camshaft journals.

    2. Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.

    3. Install the No. 2 camshaft to the camshaft housing sub-assembly.

  6. INSTALL CAMSHAFT

    Tech Tips

    Perform "Inspection After Repairs" after replacing the camshaft.

    Click here


    1. Clean the camshaft journals.

    2. Apply a light coat of engine oil to the camshaft journals and camshaft housing sub-assembly.

    3. Install the camshaft to the camshaft housing sub-assembly.

  7. INSTALL CAMSHAFT BEARING CAP


    1. A01QU5RC01
      *1 Camshaft
      *2 No. 2 Camshaft
      *3 Straight Pin

      Apply a light coat of engine oil to the camshaft bearing caps.

    2. Check the marks and numbers on the camshaft bearing caps and place the camshaft bearing caps in the proper position and direction.

      Tech Tips

      Make sure that the knock pin of the camshaft is positioned as shown in the illustration.

    3. A01QSFCE01

      Install the 10 bolts in the order shown in the illustration.

      Torque:
      16 N*m  { 163 kgf*cm, 12 ft.*lbf }

  8. INSTALL CAMSHAFT HOUSING SUB-ASSEMBLY


    1. A01QSV5C03
      *1 Lash Adjuster
      *2 Valve Rocker Arm
      *3 Valve Stem
      *4 Valve Stem Cap

      Make sure that the valve rocker arm is installed as shown in the illustration.

    2. A01QUDDC01
      *1 Continuous Line

      Apply seal packing in a continuous line as shown in the illustration.

      Seal packing
      Toyota Genuine Seal Packing Black, Three Bond 1207B or equivalent
      Standard Seal Packing Diameter
      Area Specified Condition
      Continuous Line 3.5 to 4.5 mm (0.138 to 0.177 in.)
      A 8.0 mm (0.315 in.)
      B 7.0 mm (0.276 in.)
      Application Length A and B
      15 mm (0.591 in.)

      Note


      • Remove any oil from the contact surfaces.

      • Install the camshaft housing sub-assembly within 3 minutes and tighten the bolts within 10 minutes after applying seal packing.

      • Do not start the engine for at least 2 hours after installation.

    3. A01QTPIN01

      Set the camshaft and No. 2 camshaft as shown in the illustration.

    4. Install the camshaft housing sub-assembly with the 17 bolts and tighten them in the order shown in the illustration.

      Torque:
      27 N*m  { 275 kgf*cm, 20 ft.*lbf }

      Note


      • After installing the camshaft housing sub-assembly, make sure that the cam lobes are positioned as shown in the illustration.

      • If any of the bolts are loosened during installation, remove the camshaft housing sub-assembly, clean the installation surfaces, and reapply seal packing.

      • If the camshaft housing sub-assembly is removed because any of the bolts are loosened during installation, make sure that the previously applied seal packing does not enter any oil passages.

      • After installing the camshaft housing sub-assembly, wipe off any seal packing that seeped out from between the camshaft housing sub-assembly and cylinder head.

  9. INSTALL CAMSHAFT TIMING GEAR ASSEMBLY

    Tech Tips

    Perform "Inspection After Repairs" after replacing the camshaft timing gear assembly.

    Click here


    1. A01QP1AC12
      *1 Straight Pin
      *2 Key Groove

      Put the camshaft timing gear assembly and camshaft together with the straight pin and key groove misaligned as shown in the illustration.

      Note

      Do not forcefully push in the camshaft timing gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing gear assembly.

    2. A01QUF5C01
      *1 Straight Pin
      *2 Key Groove
      *a View A

      Turn the camshaft timing gear assembly as shown in the illustration while pushing it gently against the camshaft. Push further at the position where the pin fits into the groove.

      Note

      Do not turn the camshaft timing gear assembly in the retard direction (clockwise).

    3. A01QQ6BC16
      *1 Camshaft Timing Gear Assembly
      *2 Camshaft Flange
      *a Clearance
      *b No Clearance

      Check that there is no clearance between the camshaft timing gear assembly and camshaft flange.

    4. A01QP3C

      Tighten the flange bolt while holding the hexagonal portion of the camshaft.

      Torque:
      54 N*m  { 551 kgf*cm, 40 ft.*lbf }
    5. A01QSW7C02
      A01QRKS Locks when turned all the way in this direction

      Check that the camshaft timing gear assembly can move in the retard direction (clockwise) and is locked in the most retarded position.

  10. INSTALL CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY

    Tech Tips

    Perform " Inspection After Repairs" after replacing the camshaft timing exhaust gear assembly.

    Click here


    1. A01QTLSC07
      *1 Straight Pin
      *2 Pin Hole

      Put the camshaft timing exhaust gear assembly and No. 2 camshaft together by aligning the pin hole and straight pin.

      Note

      Do not forcefully push in the camshaft timing exhaust gear assembly. This may cause the camshaft straight pin tip to damage the installation surface of the camshaft timing exhaust gear assembly.

    2. Lightly press the camshaft timing exhaust gear assembly against the No. 2 camshaft and turn the camshaft timing exhaust gear assembly. Push further at the position where the straight pin enters the pin hole.

    3. A01QQ6BC17
      *1 Camshaft Timing Exhaust Gear Assembly
      *2 Camshaft Flange
      *a Clearance
      *b No Clearance

      Check that there is no clearance between the camshaft timing exhaust gear assembly and camshaft flange.

    4. A01QOQI

      Tighten the flange bolt while holding the hexagonal portion of the No. 2 camshaft.

      Torque:
      54 N*m  { 551 kgf*cm, 40 ft.*lbf }

    5. Check the camshaft timing exhaust gear assembly lock.


      1. Make sure that the camshaft timing exhaust gear assembly is locked.

  11. INSTALL CHAIN SUB-ASSEMBLY

    Click here