SFI SYSTEM, Diagnostic DTC:P0336

DTC Code DTC Name
P0336 Crankshaft Position Sensor "A" Circuit Range / Performance

DESCRIPTION

The crankshaft position sensor monitors the stop position and performs start control from the position of the stopped crankshaft. Moreover, the crankshaft position sensor contains a function which detects reverse rotation to correctly detect the stop position when the engine rotates reversely.

When a malfunction occurs in the reverse rotation detection function, stop and start system is disabled.

DTC No. Detection Item DTC Detection Condition Trouble Area MIL Memory
P0336 Crankshaft Position Sensor "A" Circuit Range / Performance

When one of the following conditions is met (1 trip detection logic):


  • In case an engine reverse signal is detected for 4 seconds during engine cranking or normally rotating at 900 rpm or higher.

  • In case the pulse width of the crankshaft position sensor exceeding the threshold is detected for 4 seconds during engine rotation at 900 rpm or higher.

  • In case the input signal voltage of the crankshaft position sensor continues at 4.7 V for 4 seconds during engine rotation.

  • Open or short in crankshaft position sensor circuit

  • Crankshaft position sensor

  • No. 1 crankshaft position sensor plate

  • ECM

 Comes on DTC stored

MONITOR DESCRIPTION

When one of the following malfunctions is detected, P0336 is output.


  1. In case an engine reverse signal is detected for 4 seconds during engine cranking or normally rotating at 900 rpm or higher.

  2. In case the pulse width of the crankshaft position sensor exceeding the threshold is detected for 4 seconds during engine normal rotation at 900 rpm or higher.

  3. In case the input signal voltage of the crankshaft position sensor continues at 4.7 V for 4 seconds during engine rotation.

CONFIRMATION DRIVING PATTERN


  1. Connect the GTS to the DLC3.

  2. Turn the ignition switch to ON and turn the GTS on.

  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC procedure).

  4. Turn the ignition switch off and wait for at least 30 seconds.

  5. Turn the ignition switch to ON and turn the GTS on.

  6. Start the engine.

  7. Idle the engine for 20 seconds or more.

  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  9. Read the pending DTCs.

    Tech Tips


    • If a pending DTC is output, the system is malfunctioning.

    • If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  11. Input the DTC: P0336.

  12. Check the DTC judgment result.

    GTS Display Description
    NORMAL

    • DTC judgment completed

    • System normal
    ABNORMAL

    • DTC judgment completed

    • System abnormal
    INCOMPLETE

    • DTC judgment not completed

    • Perform driving pattern after confirming DTC enabling conditions
    N/A

    • Unable to perform DTC judgment

    • Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    Tech Tips


    • If the judgment result shows NORMAL, the system is normal.

    • If the judgment result shows ABNORMAL, the system has a malfunction.

    • If the judgment result shows INCOMPLETE or N/A, perform the Confirmation Driving Pattern and check the DTC judgment result again.

WIRING DIAGRAM

Refer to DTC P0335 Click here.

CAUTION / NOTICE / HINT

Tech Tips

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

PROCEDURE


  1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0336)


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    5. Read the DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      DTC P0336 and P0338 are output A
      DTC P0336 is output B

    B

    GO TO STEP 6 Click here

    A

  2. CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)


    1. A01KD2SC25
      *a

      Front view of wire harness connector

      (to Crankshaft Position Sensor)

      Disconnect the crankshaft position sensor connector.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage
      Tester Connection Condition Specified Condition
      B88-1 (VC) - Body ground Ignition switch ON 4.5 to 5.5 V
      Result
      Proceed to
      OK
      NG

    NG

    CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM) Click here

    OK

  3. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)


    1. Disconnect the crankshaft position sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B88-3 (NE+) - B93-114 (NE+) Always Below 1 Ω
      B88-2 (NE-) - B93-113 (NE-) Always Below 1 Ω
      B88-3 (NE+) or B93-114 (NE+) - Body ground and other terminals Always 10 kΩ or higher
      B88-2 (NE-) or B93-113 (NE-) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR

    OK

  4. CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)


    1. A01KDRZC07
      *a Clearance

      Check the crankshaft position sensor installation condition.

      OK
      Crankshaft position sensor is installed correctly.
      Result
      Proceed to
      OK
      NG

    NG

    SECURELY REINSTALL CRANKSHAFT POSITION SENSOR Click here

    OK

  5. INSPECT NO. 1 CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)


    1. Inspect the teeth of the No. 1 crankshaft position sensor plate.

      OK
      No. 1 crankshaft position sensor plate does not have any cranks or deformation.
      Result
      Proceed to
      OK
      NG

    NG

    REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE Click here

    OK

  6. REPLACE CRANKSHAFT POSITION SENSOR


    1. Replace the crankshaft position sensor Click here.

      Result
      Proceed to
      NEXT

    NEXT

  7. CHECK WHETHER DTC OUTPUT RECURS


    1. Connect the GTS to the DLC3.

    2. Turn the ignition switch to ON.

    3. Turn the GTS on.

    4. Clear the DTCs.


      Powertrain > Engine and ECT > Clear DTCs

    5. Turn the ignition switch off and wait for at least 30 seconds.

    6. Start the engine.

    7. Turn the GTS on.

    8. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

    9. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

    10. Read the DTCs.


      Powertrain > Engine and ECT > Trouble Codes
      Result
      Result Proceed to
      DTCs are not output A
      DTC P0336 is output B

    A

    END

    B

    REPLACE ECM Click here

  8. CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)


    1. Disconnect the crankshaft position sensor connector.

    2. Disconnect the ECM connector.

    3. Measure the resistance according to the value(s) in the table below.

      Standard Resistance
      Tester Connection Condition Specified Condition
      B88-1 (VC) - B93-81 (VCNE) Always Below 1 Ω
      B88-1 (VC) or B93-81 (VCNE) - Body ground and other terminals Always 10 kΩ or higher
      Result
      Proceed to
      OK
      NG

    OK

    REPLACE ECM Click here

    NG

    REPAIR OR REPLACE HARNESS OR CONNECTOR