PROCEDURES NECESSARY WHEN BATTERY TERMINAL IS DISCONNECTED/RECONNECTED
| Necessary Procedures | Effect/Inoperative Function When Necessary Procedures are not Performed | Link |
|---|---|---|
| Drive the vehicle until stop and start control is permitted (approximately 15 to 40 minutes) | Stop and start system | |
| Reset back door close position |
|
Note
After the ignition switch is turned off, the navigation receiver assembly requires approximately a minute to record various types of memory and settings. As a result, after turning the ignition switch off, wait a minute or more before disconnecting the cable from the negative (-) battery terminal.
PROCEDURES NECESSARY WHEN ECU OR OTHER PARTS ARE REPLACED
| Replacement Part | Necessary Procedure | Link | ||
|---|---|---|---|---|
for 1AD-FTV: |
|
Engine start | ||
for 1AD-FTV: |
|
|
||
for 1AD-FTV: |
Crank Time Compensation Reset |
|
||
for 1AD-FTV: |
A/F Sensor Compensation Reset |
|
||
for 1AD-FTV |
Supply Pump Initialization |
|
||
for 1AD-FTV: |
Catalyst Record Clear |
|
||
for 1AD-FTV: |
|
DTC is output. | ||
for 1AD-FTV: |
Register VIN | DTC P0630 is input | ||
for 1AD-FTV: |
ECD System initialization | Engine start | ||
for 2AD-FHV: |
|
Engine start | ||
for 2AD-FHV: |
|
|
||
for 2AD-FHV: |
Clear Crank Time Compensation Data |
|
||
for 2AD-FHV: |
A/F Sensor Compensation Reset |
|
||
for 2AD-FHV: |
Supply Pump Initialization |
|
||
for 2AD-FHV: |
Catalyst Record Clear |
|
||
for 2AD-FHV: |
|
DTC is output. | ||
for 2AD-FHV: |
Register VIN | DTC P0630 is input | ||
for 2AD-FHV: |
ECD System initialization | Engine start | ||
for 2AD-FTV, CCo: |
|
Engine start | ||
for 2AD-FTV, CCo: |
|
|
||
for 2AD-FTV, CCo: |
Clear Crank Time Compensation Data |
|
||
for 2AD-FTV, CCo: |
Supply Pump Initialization |
|
||
for 2AD-FTV, CCo: |
|
DTC is output. | ||
for 2AD-FTV, CCo: |
Register VIN | DTC P0630 is input | ||
for 2AD-FTV, CCo: |
ECD System initialization | Engine start | ||
for 2AD-FTV, DPF: |
|
Engine start | ||
for 2AD-FTV, DPF: |
|
|
||
for 2AD-FTV, DPF: |
Clear Crank Time Compensation Data |
|
||
for 2AD-FTV, DPF: |
A/F Sensor Compensation Reset |
|
||
for 2AD-FTV, DPF: |
Supply Pump Initialization |
|
||
for 2AD-FTV, DPF: |
Catalyst Record Clear |
|
||
for 2AD-FTV, DPF: |
|
DTC is output. | ||
for 2AD-FTV, DPF: |
Register VIN | DTC P0630 is input | ||
for 2AD-FTV, DPF: |
ECD System initialization | Engine start | ||
for 2AR-FE, w/ Canister Pump Module: |
Register VIN | DTC P0630 is input | ||
for 2AR-FE, w/o Canister Pump Module: |
Register VIN | DTC P0630 is input | ||
for 2AR-FE, w/ Canister Pump Module: |
Inspection after repair | Poor idle, engine starting, etc. | ||
for 2AR-FE, w/o Canister Pump Module: |
Inspection after repair | Poor idle, engine starting, etc. | ||
for 3ZR-FAE: |
Register VIN | - | ||
for 3ZR-FAE: |
Inspection after repair | Poor idle, engine starting, etc. | ||
for 3ZR-FE: |
Register VIN | DTC P0630 is input | ||
for 3ZR-FE: |
Inspection after repair | Poor idle, engine starting, etc. | ||
|
Adjust lane departure warning camera | DTCs are output | ||
w/ Stop and Start System: |
|
Stop and start system | ||
w/ Stop and Start System: |
Clear the number of starter operations | |||
w/ Stop and Start System: |
|
|||
w/ Stop and Start System: |
|
|||
for U660F: |
|
|
for Initialization: Click here for Registration: Click here |
|
for U660F: |
|
|
||
for U660F: |
Perform road test to allow TCM to learn |
|
||
for U660F: |
Possible |
|
|
|
| Impossible |
|
|
||
for U760E: |
|
|
for Initialization: Click here for Registration: Click here |
|
for U760E: |
|
|
||
for U760E: |
Perform road test to allow ECM to learn |
|
||
for U760E: |
Possible |
|
|
|
| Impossible |
|
|
||
for U760F: |
|
|
for Initialization: Click here for Registration: Click here |
|
for U760F: |
|
|
||
for U760F: |
Perform road test to allow ECM to learn |
|
||
for U760F: |
Possible |
|
|
|
| Impossible |
|
|
||
for K111: |
|
|
||
for K111F: |
|
|
||
|
Clear zero point calibration data | Dynamic torque control 4WD/AWD system | ||
|
|
Tire pressure warning system | for Registration: Click here for Initialization: Click here |
|
| Skid control ECU (brake actuator assembly) | Yaw rate and acceleration sensor zero point calibration. | Vehicle stability control system | ||
| Yaw rate and acceleration sensor (airbag sensor assembly) |
|
Vehicle stability control system | ||
| Wheel alignment adjustment |
|
Vehicle stability control system | ||
| Power steering ECU assembly | Assist map writing | Power steering system | ||
| Navigation ECU sub-assembly | Calibration | Parking assist monitor system | ||
| Spiral with sensor cable sub-assembly |
|
|||
| Suspension, tires, etc. | Television camera assembly optical axis (Back camera position setting) | |||
| Television camera assembly | ||||
| Blind spot monitor sensor | Blind spot monitor beam axis adjustment |
|
||
w/ Entry and Start System: |
Registration |
|
Refer to the Service Bulletin for the registration method | |
w/o Entry and Start System: |
Registration | Engine starting | Refer to the Service Bulletin for the registration procedure. | |
w/o Entry and Start System: |
Register recognition code | Wireless door lock operation | ||
w/ Blocking System: |
Registration | Engine starting | Refer to the Service Bulletin for the registration procedure. | |
|
|
|
||
for Automatic Air Condition System: |
Initialization servo motor | Initialization servo motor | ||
w/ Jam Protection Function: |
Initialize power window control system |
|
||
|
Initialize sliding roof ECU (pulse sensor initial position setting) |
|
||
w/ Power Back Door System: |
Initialize back door closer system | Back door lock operation | ||
w/ Power Back Door System: |
Initialize power back door system | Power back door system | ||
|
Height leveling ECU initialization | Height leveling function | ||
*1: w/ Multi-information Display (Dot Display Type)