ТРОС МЕХАНИЗМА ПЕРЕКЛЮЧЕНИЯ ПЕРЕДАЧ УСТАНОВКА

PROCEDURE

1. INSTALL TRANSMISSION CONTROL CABLE ASSEMBLY

   
   

   1. Pass the transmission control cable assembly into the vehicle and install the transmission control cable assembly to the vehicle body with the 2 nuts.

      Torque:

      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

   2. Connect the transmission control cable assembly to the rear engine mounting insulator with the bolt.

      Torque:

      5.0 N*m  { 51 kgf*cm, 44 in.*lbf }

   3. 

      Connect the transmission control cable assembly to the control cable bracket assembly with 2 new clips (A).

   4. Connect the transmission control cable assembly to the manual transaxle assembly with the 2 clips (B).

   5. 

      *a	Lock Piece
      *b	Stopper
      *c	Adjuster Case
      *d	Twist the stopper
      *e	Pull out
      *f	Return the stopper

      Release the lock of the transmission control select cable length adjustment structure.

      
      

      1. Twist the stopper.

      2. Pull the lock piece outward from the adjuster case to release the lock.

      3. Return the stopper.

   6. Engage the 2 claws to connect the transmission control cable assembly to the floor shift lever assembly.

   7. Connect the transmission control shift cable to the floor shift lever assembly.

   8. 

      Connect the transmission control select cable to the floor shift lever assembly and install the clip.

      Note

      
      

      • Make sure that the lock piece of the transmission control select cable length adjustment structure is facing upward when the transmission control select cable is connected.

      • Make sure that the transmission control select cable is securely installed.

   9. 

      *1	Outer Lever
      *2	Reverse Restrict Pin Assembly
      *a	Secured

      Hook the outer lever of the manual transaxle assembly to the reverse restrict pin assembly to secure it.

   10. 

       *a	Slider Shaft
       *b	Cam Wall

       Push the slider shaft against the cam wall.

       Note

       
       

       • Do not pull up the slider shaft.

       • When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.

   11. Lock the transmission control select cable length adjustment structure.

       
       

       1. Twist the stopper.

          

          *a	Lock Piece	*b	Stopper
          *c	Adjuster Case	*d	Twist the stopper
          *e	Push	*f	Return the stopper

       2. Push the lock piece into the adjuster case with slider held against the cam wall.

          Note

          
          

          • Securely press in the lock piece until the lock engages.

          • When adjusting the transmission control select cable, make sure that the shift lever is not in 1st or 2nd.

       3. Return the stopper to prevent the lock from being released.

          Note

          
          

          • Push the lock piece as far as it will go.

          • Confirm whether the transmission control select cable length adjustment structure is locked securely.

   12. 

       *1	Outer Lever
       *2	Reverse Restrict Pin Assembly
       *a	Released

       Move the shift lever to the reverse position, so that the outer lever can be released.

2. INSTALL REAR CONSOLE BOX ASSEMBLY (for Hatchback, Wagon)

   Click here

3. INSTALL REAR CONSOLE BOX ASSEMBLY (for Sedan)

   Click here

4. INSTALL NO. 1 FRONT FLOOR HEAT INSULATOR

   
   

   1. Install the No. 1 front floor heat insulator to the vehicle body with the 3 nuts.

      Torque:

      5.5 N*m  { 56 kgf*cm, 49 in.*lbf }

5. INSTALL FRONT EXHAUST PIPE ASSEMBLY

   Click here

6. INSTALL AIR CLEANER CASE SUB-ASSEMBLY

   Click here

7. INSTALL AIR CLEANER CAP WITH AIR CLEANER HOSE

   Click here