ВЫПУСКНОЙ КОЛЛЕКТОР С ТУРБОНАГНЕТАТЕЛЕМ УСТАНОВКА

PROCEDURE


  1. INSTALL STUD BOLT

    Tech Tips

    If a stud bolt is deformed or the threads are damaged, replace it.


    1. For turbocharger sub-assembly:


      1. A00YARBC02
        *a 47 mm (1.85 in.)
        *b 14 mm (0.551 in.)
        *c 15 mm (0.591 in.)

        Using an E8 "TORX" wrench, install the stud bolt to the turbocharger sub-assembly.

        Torque:
        8.0 N*m  { 82 kgf*cm, 71 in.*lbf }
      2. A00Y852C02
        *a 32 mm (1.26 in.)
        *b 20 mm (0.787 in.)
        *c 10 mm (0.394 in.)

        Using an E8 "TORX" wrench, install the 3 stud bolts to the turbocharger sub-assembly.

        Torque:
        10 N*m  { 102 kgf*cm, 7 ft.*lbf }
      3. A00Y526C01
        *a 43 mm (1.69 in.)
        *b 16 mm (0.630 in.)
        *c 24.5 mm (0.965 in.)
        *d 12 mm (0.472 in.)
        *e 9.0 mm (0.354 in.)

        Install the 2 stud bolts (A).

        Torque:
        20 N*m  { 204 kgf*cm, 15 ft.*lbf }

      4. Using an E5 "TORX" wrench, install the 2 stud bolts (B).

        Torque:
        5.0 N*m  { 51 kgf*cm, 44 in.*lbf }
    2. A00YBDFC02
      *a 43 mm (1.69 in.)
      *b 16 mm (0.630 in.)

      For exhaust manifold:

      Install the stud bolt to the exhaust manifold.

      Torque:
      20 N*m  { 204 kgf*cm, 15 ft.*lbf }

  2. INSTALL EXHAUST MANIFOLD AND TURBOCHARGER SUB-ASSEMBLY


    1. A00Y86XC01
      *1 Collar
      *2 Groove

      Temporarily install a new gasket, the exhaust manifold, and 2 collars with 2 new nuts (A). Tighten the nuts until the mating surface of the exhaust manifold contacts the cylinder head.

    2. Temporarily install the 6 collars with 6 new nuts.

      Tech Tips


      • When installing the collars, pay attention to the mounting orientation. The ring groove of the collar should be on the outside. Refer to the illustration.

      • Do not fully tighten the nuts as doing so may result in misalignment of the exhaust manifold.

    3. Install a new gasket and the turbocharger with 3 new nuts.

      Torque:
      60 N*m  { 612 kgf*cm, 44 ft.*lbf }
    4. A00Y7DLC01
      *1 New Turbocharger Stay
      *2 Collar

      Install the 2 collars and a new turbocharger stay with 2 new nuts.

      Torque:
      36 N*m  { 367 kgf*cm, 27 ft.*lbf }

      Note


      • Do not reuse the turbocharger stay.

      • When installing the turbocharger stay, be sure to tighten the nut (A) first.

    5. Tighten the 8 nuts of the exhaust manifold.

      Torque:
      47 N*m  { 479 kgf*cm, 35 ft.*lbf }

  3. INSTALL TURBO OIL OUTLET PIPE


    1. Install a new gasket and the turbo oil outlet pipe with the 3 nuts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

    2. Connect the turbo oil outlet pipe and a new gasket with the union bolt.

      Torque:
      35 N*m  { 357 kgf*cm, 26 ft.*lbf }

  4. INSTALL NO. 3 WATER BY-PASS HOSE


    1. Install the No. 3 water by-pass hose and slide the 2 clips to secure it.

  5. INSTALL NO. 2 VACUUM TRANSMITTING PIPE SUB-ASSEMBLY


    1. Install the No. 2 vacuum transmitting pipe with the bolt.

      Torque:
      21 N*m  { 214 kgf*cm, 15 ft.*lbf }

    2. Connect the 2 vacuum transmitting hoses.

  6. INSTALL TURBOCHARGER WIRE


    1. Install the turbocharger wire and engage the 3 wire harness clamps.

    2. Connect the 2 connectors.

  7. INSTALL NO. 2 TURBO OIL OUTLET PIPE


    1. Install a new gasket and the No. 2 turbo oil outlet pipe with the 2 bolts.

      Torque:
      11 N*m  { 112 kgf*cm, 8 ft.*lbf }

  8. INSTALL TURBO OIL OUTLET HOSE


    1. Install the turbo oil outlet hose and slide the 2 clips to secure it.

  9. INSTALL NO. 1 TURBO INSULATOR


    1. Install the No. 1 turbo insulator with the 2 bolts.

      Torque:
      20.5 N*m  { 209 kgf*cm, 15 ft.*lbf }

  10. INSTALL EGR PIPE WITH COOLER SUB-ASSEMBLY

    Click here

  11. PERFORM TURBOCHARGER INITIALIZATION

    Click here