МОНОЛИТНЫЙ КАТАЛИТИЧЕСКИЙ НЕЙТРАЛИЗАТОР СНЯТИЕ

PROCEDURE


  1. REMOVE INTERCOOLER ASSEMBLY

    Click here

  2. REMOVE WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here

  3. REMOVE WATER GUARD PLATE LH (for LHD)

    Click here

  4. REMOVE WATER GUARD PLATE LH (for RHD)

    Click here

  5. REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for LHD)

    Click here

  6. REMOVE NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL (for RHD)

    Click here

  7. REMOVE OUTER COWL TOP PANEL (for LHD)

    Click here

  8. REMOVE OUTER COWL TOP PANEL (for RHD)

    Click here

  9. REMOVE AIR FUEL RATIO SENSOR

    Click here

  10. REMOVE NO. 1 HOSE TO HOSE TUBE


    1. B0042EJC02
      *A for LHD
      *B for RHD

      Slide the clip and disconnect the check valve to connector tube hose from the No. 1 hose to hose tube.

    2. Slide the clip and disconnect the union to connector tube hose from the No. 1 hose to hose tube.

    3. B0044AOC02
      *A for LHD
      *B for RHD

      Remove the 2 nuts and No. 1 hose to hose tube from the vehicle body.

  11. REMOVE AIR CLEANER CAP WITH AIR CLEANER HOSE


    1. B0044J7C02
      *a Air Cleaner Cap Sub-assembly Clamp
      *b Guide

      Disconnect the intake mass air flow meter sub-assembly connector.

    2. Disengage the wire harness from the air cleaner cap sub-assembly.

    3. Disengage the 2 air cleaner cap sub-assembly clamps.

    4. Disengage the 2 guides to separate the air cleaner cap sub-assembly from the air cleaner case sub-assembly.

    5. Loosen the hose clamp and remove the air cleaner cap with air cleaner hose from the inlet No. 1 air duct sub-assembly.

  12. REMOVE ENGINE WIRE


    1. B0042Z3C02
      B0042CO Bolt
      B0043VS Nut
      B0043HC Connector

      Disconnect the 7 connectors.

    2. Remove the bolt and nut.

    3. Disengage the 3 wire harness clamps.

    4. B004288

      Remove the 2 bolts and wire harness clamp bracket from the cylinder head sub-assembly.

  13. REMOVE VENTILATION HOSE


    1. B0043IQC02
      *1 Ventilation Hose
      *2 No. 4 Ventilation Hose

      Slide the 2 clips and remove the ventilation hose from the cylinder head cover sub-assembly and inlet No. 1 air duct sub-assembly.

    2. Slide the 2 clips and remove the No. 4 ventilation hose from the ventilation ejector and inlet No. 1 air duct sub-assembly.

  14. REMOVE VENTILATION EJECTOR


    1. B00447V

      Remove the 2 bolts and ventilation ejector from the cylinder head cover sub-assembly.

    2. Remove the O-ring from the cylinder head cover sub-assembly.

  15. REMOVE AIR TUBE ASSEMBLY


    1. B0043UMC02
      *1 No. 2 Intercooler Water Hose
      *2 No. 3 Intercooler Water Hose

      Slide the clip and disconnect the No. 2 intercooler water hose and No. 3 intercooler water hose from the turbocharger sub-assembly.

    2. B00450KC02
      *1 No. 2 Intercooler Water Hose
      *2 No. 3 Intercooler Water Hose

      Disconnect the No. 2 intercooler water hose and No. 3 intercooler water hose from the No. 1 water hose clamp bracket.

    3. B004382

      Loosen the hose clamp and remove the air tube assembly from the turbocharger sub-assembly.

    4. B0043EJ

      Remove the bolt and air tube assembly from the cylinder head cover sub-assembly.

  16. REMOVE VACUUM REGULATING VALVE ASSEMBLY


    1. B0042X8C02
      *1 No. 2 Vacuum Transmitting Hose Assembly
      *2 No. 3 Vacuum Transmitting Hose Assembly
      *3 Vacuum Regulating Valve Assembly
      *4 No. 2 Vacuum Switching Valve Bracket

      Disconnect the No. 2 vacuum transmitting hose assembly and No. 3 vacuum transmitting hose assembly from the vacuum regulating valve assembly.

    2. Remove the 3 bolts and vacuum regulating valve assembly and No. 2 vacuum switching valve bracket from the cylinder head sub-assembly.

  17. REMOVE INLET NO. 1 AIR DUCT SUB-ASSEMBLY


    1. B0043T6

      Disconnect the No. 1 vacuum transmitting hose assembly from the vacuum tank.

    2. B0044A3

      Remove the 2 bolts and vacuum tank from the inlet No. 1 air duct sub-assembly.

    3. B00453H

      Disconnect the No. 1 vacuum transmitting hose assembly from the vacuum pump assembly.

    4. B004542C01

      Remove the bolt and disconnect the inlet No. 1 air duct sub-assembly from the fuel pump protector.

    5. B0042JSC02
      *1 No. 2 Vacuum Transmitting Hose Assembly
      *2 Inlet No. 1 Air Duct Sub-assembly

      Disconnect the No. 2 vacuum transmitting hose assembly from the turbocharger sub-assembly.

    6. Loosen the hose clamp and remove the inlet No. 1 air duct sub-assembly from the turbocharger sub-assembly.

  18. REMOVE NO. 1 ENGINE COVER


    1. B0043Y6

      Remove the No. 1 engine cover from the cylinder head cover sub-assembly and cylinder head sub-assembly.

  19. REMOVE FRONT CENTER FLOOR BRACE SUB-ASSEMBLY

    Click here

  20. REMOVE FRONT EXHAUST PIPE ASSEMBLY (TWC: Rear Catalyst)


    1. B00431B

      Disconnect the heated oxygen sensor connector.

    2. Disengage the 2 wire harness clamps and disconnect the wire harness from the wire harness clamp bracket.

    3. B0041PN

      Remove the 4 bolts and 4 compression springs and disconnect the front exhaust pipe assembly (TWC: Rear Catalyst) from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and tail exhaust pipe assembly.

    4. Remove the front exhaust pipe assembly (TWC: Rear Catalyst) from the 2 exhaust pipe supports.

    5. Remove the 2 exhaust pipe gaskets from the exhaust manifold converter sub-assembly (TWC: Front Catalyst) and tail exhaust pipe assembly.

  21. REMOVE FRONT NO. 1 FLOOR HEAT INSULATOR

    Click here

  22. REMOVE DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY


    1. B0042GU

      Remove the bolt, nut and drive shaft heat insulator sub-assembly from the cylinder block sub-assembly and manifold support bracket.

  23. REMOVE MANIFOLD SUPPORT BRACKET


    1. B0044HF

      Remove the bolt and manifold support bracket from the cylinder block sub-assembly and exhaust manifold converter sub-assembly (TWC: Front Catalyst).

  24. REMOVE NO. 2 TURBO INSULATOR


    1. B00435R

      Remove the 2 bolts and No. 2 turbo insulator from the cylinder head sub-assembly and heat insulator bracket.

  25. REMOVE NO. 1 MANIFOLD CONVERTER INSULATOR


    1. B004482

      Remove the 3 bolts and No. 1 manifold converter insulator from the exhaust manifold converter sub-assembly (TWC: Front Catalyst).

  26. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY (TWC: Front Catalyst)


    1. B0043O4

      Remove the 4 nuts and exhaust manifold converter sub-assembly (TWC: Front Catalyst) from the turbocharger sub-assembly.

  27. REMOVE OUTLET TURBINE ELBOW GASKET


    1. B0043WK

      Remove the outlet turbine elbow gasket from the turbocharger sub-assembly.