Click here

ДАТЧИК ТЕМПЕРАТУРЫ ОТРАБОТАВШИХ ГАЗОВ (для моделей с контроллером свечей накаливания) УСТАНОВКА

Click here
Click here

PROCEDURE


  1. Click here

    INSTALL NO. 2 EXHAUST GAS TEMPERATURE SENSOR

    Note:

    If the No. 2 exhaust gas temperature sensor is dropped, replace it with a new one.


    1. B0044TVC01
      *a Torque Wrench Fulcrum Length

      Using a 14 mm union nut wrench, install the No. 2 exhaust gas temperature sensor to the No. 2 exhaust manifold.

      Specified tightening torque
      30 N*m 306 kgf*cm 22 ft.*lbf
      Tip:

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26 N*m (265 kgf*cm, 19 ft.*lbf)

  2. Click here

    INSTALL NO. 2 EXHAUST MANIFOLD

    Click here

  3. Click here

    INSTALL DRIVE SHAFT HEAT INSULATOR SUB-ASSEMBLY

    Click here

  4. Click here

    INSTALL NO. 4 MANIFOLD SUPPORT BRACKET

    Click here

  5. Click here

    INSTALL FRONT SUSPENSION CROSSMEMBER SUB-ASSEMBLY

    Click here

  6. Click here

    INSTALL NO. 5 MANIFOLD SUPPORT BRACKET

    Click here

  7. Click here

    INSTALL FRONT NO. 1 FLOOR HEAT INSULATOR

    Click here

  8. Click here

    INSTALL FRONT EXHAUST PIPE ASSEMBLY

    Click here

  9. Click here

    INSTALL FRONT CENTER FLOOR BRACE SUB-ASSEMBLY

    Click here

  10. Click here

    INSTALL FRONT DRIVE SHAFT ASSEMBLY RH

    Click here

  11. Click here

    INSTALL NO. 1 TURBO INSULATOR

    Click here

  12. Click here

    INSTALL NO. 1 AIR TUBE

    Click here

  13. Click here

    INSTALL AIR CLEANER CASE SUB-ASSEMBLY

    Click here

  14. Click here

    INSTALL AIR CLEANER CAP SUB-ASSEMBLY

    Click here

  15. Click here

    INSTALL BATTERY

    Click here

  16. Click here

    INSTALL NO. 2 HOSE TO HOSE TUBE (for LHD)

    Click here

  17. Click here

    INSTALL NO. 2 HOSE TO HOSE TUBE (for RHD)

    Click here

  18. Click here

    INSTALL NO. 2 ENGINE COVER BRACKET

    Click here

  19. Click here

    INSTALL SENSOR BRACKET

    Click here

  20. Click here

    INSTALL DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

    Click here

  21. Click here

    INSTALL EXHAUST GAS TEMPERATURE SENSOR

    Note:

    If the exhaust gas temperature sensor is dropped, replace it with a new one.


    1. B004406C02
      *a Torque Wrench Fulcrum Length

      Using a 14 mm union nut wrench, install the exhaust gas temperature sensor to the No. 2 exhaust manifold.

      Specified tightening torque
      30 N*m 306 kgf*cm 22 ft.*lbf
      Tip:

      • Calculate the torque wrench reading when changing the fulcrum length of the torque wrench.

        Click here

      • When using a 14 mm union nut wrench (fulcrum length of 25 mm (0.984 in.)) + torque wrench (fulcrum length of 180 mm (7.09 in.)): 26 N*m (265 kgf*cm, 19 ft.*lbf)

    2. Engage the clamp to connect the wire harness to the wire harness clamp bracket.

    3. Engage the claw to connect the exhaust gas temperature sensor connector to the wire harness clamp bracket.

    4. Install the wire harness clamp bracket to the timing chain cover assembly with the bolt.

      9.0 N*m 92 kgf*cm 80 in.*lbf

    5. Connect the exhaust gas temperature sensor connector.

  22. Click here

    INSTALL WIRE HARNESS CLAMP BRACKET

    Click here

  23. Click here

    INSTALL NO. 1 WIRE HARNESS HEAT INSULATOR

    Click here

  24. Click here

    INSTALL OUTER COWL TOP PANEL


  25. Click here

    INSTALL NO. 2 HEATER AIR DUCT SPLASH SHIELD SEAL


  26. Click here

    INSTALL WATER GUARD PLATE LH


  27. Click here

    INSTALL WINDSHIELD WIPER MOTOR AND LINK ASSEMBLY

    Click here

  28. Click here

    INSTALL NO. 1 ENGINE COVER (w/ No. 1 Engine Cover)

    Click here

  29. Click here

    LEARNING DIFFERENTIAL PRESSURE SENSOR ASSEMBLY

    Click here

  30. Click here

    CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

    Note:

    When disconnecting the cable, some systems need to be initialized after the cable is reconnected.

    Click here

  31. Click here

    INSPECT FOR EXHAUST GAS LEAK