ТОПЛИВНЫЙ НАСОС СНЯТИЕ

PROCEDURE


  1. REMOVE REAR SEAT CUSHION ASSEMBLY

    Click here

  2. REMOVE REAR FLOOR SERVICE HOLE COVER


    1. A002ZWO

      Disconnect the 2 connectors.

    2. A0030WYC01
      *A w/o Combustion Type Power Heater
      *B w/ Combustion Type Power Heater

      Remove the rear floor service hole cover and butyl tape.

    3. Disconnect the fuel pump connector.

  3. DISCONNECT FUEL RETURN TUBE SUB-ASSEMBLY


    1. Remove the tube joint clip, and pull off the fuel tube joint of the fuel return tube sub-assembly.

      A0030RZC01
      *A w/o Combustion Type Power Heater *B w/ Combustion Type Power Heater
      *1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
      *3 Fuel Tank Return Tube Sub-assembly - -
      *a Fuel Tube Joint *b O-ring
      *c Nylon Tube - -
      A0030PX Pull off A003094 Pull off

      Note


      • Remove any foreign matter on the fuel tube joint before performing this work.

      • Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

      • Be sure to disconnect the fuel tube joint by hand.

      • Do not bend, twist, pinch or kink the nylon tube.

      • Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube joint.

      • If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.

  4. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY


    1. Remove the tube joint clip, and pull off the fuel tube joint of the fuel tank main tube sub-assembly.

      A003002C01
      *A w/o Combustion Type Power Heater *B w/ Combustion Type Power Heater
      *1 Fuel Suction Plate Sub-assembly *2 Tube Joint Clip
      *3 Fuel Tank Main Tube Sub-assembly - -
      *a Fuel Tube Joint *b O-ring
      *c Nylon Tube - -
      A0030PX Pull off A003094 Pull off

      Note


      • Remove any foreign matter on the fuel tube joint before performing this work.

      • Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

      • Be sure to disconnect the fuel tube joint by hand.

      • Do not bend, twist, pinch or kink the nylon tube.

      • Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube joint.

      • If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.

  5. DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY (w/ Combustion Type Power Heater)


    1. A002ZTEC01
      *1 Fuel Suction Plate Sub-assembly
      *2 Tube Joint Clip
      *3 No. 2 Fuel Main Tube Sub-assembly
      *a Fuel Tube Joint
      *b O-ring
      *c Nylon Tube
      A0030PX Pull off
      A003094 Pull off

      Remove the tube joint clip, and pull off the fuel tube joint of the No. 2 fuel main tube sub-assembly.

      Note


      • Remove any foreign matter on the fuel tube joint before performing this work.

      • Do not scratch or allow any foreign matter to get on the parts when disconnecting them as the fuel tube connector has O-rings that seal the pipe (fuel pipe).

      • Be sure to disconnect the fuel tube joint by hand.

      • Do not bend, twist, pinch or kink the nylon tube.

      • Protect the disconnected part by covering it with a plastic bag after disconnecting the fuel tube joint.

      • If the fuel tube joint and fuel suction plate sub-assembly are stuck, push and pull to release them.

  6. REMOVE TANK SUCTION TUBE SUPPORT


    1. A00302SC01
      A0030PX Pinch
      A003094 Pull

      Pinch the tabs (A) from both sides of the fuel tank evaporation vent tube sub-assembly.

    2. Pull the fuel tank evaporation vent tube sub-assembly in the direction indicated by the arrow in the illustration.

    3. A00313C

      Disengage the 2 claws and remove the tank suction tube support.

  7. REMOVE FUEL PUMP GAUGE RETAINER

    Note

    Before performing these procedures, first cover the connector and fuel tube joints of the fuel suction tube with pump and gauge assembly with vinyl tape and then clean any dirt and foreign matter in order to prevent contamination of the fuel system.


    1. A00314EC01
      *a Paint Mark
      *b Front

      Place paint marks on the fuel suction tube with pump and gauge assembly and vehicle body as shown in the illustration.

      Note


      • The fuel suction tube with pump and gauge assembly has 2 protrusions that engage with 2 notches on the fuel tank assembly to ensure correct alignment and to prevent the fuel suction tube with pump and gauge assembly from turning during installation and removal of the fuel pump gauge retainer.

      • If the fuel pump gauge retainer is turned with the fuel suction tube with pump and gauge assembly misaligned, the fuel suction tube with pump and gauge assembly will turn with the fuel pump gauge retainer and may be damaged.

      • The paint marks are used to ensure that the fuel suction tube with pump and gauge assembly does not turn with the fuel pump gauge retainer.

    2. Install SST to the fuel pump gauge retainer.


      1. A00316CC01
        *1 Fuel Pump Gauge Retainer
        *a SST (Claw)
        *b SST (Plate)
        *c SST (Bolt)
        *d Narrow
        *e Wide
        *f Correct
        *g Incorrect

        Temporarily install SST (plate), SST (claw) and SST (bolt) to the fuel pump gauge retainer.

        SST
        09808-14030   ( 09808-01020, 09808-01030, 09808-01050 )
        09808-01071

        Note


        • Install SST (claw) to the correct location.

        • Do not install SST (claw) to a location where the pitch between ribs of the fuel pump gauge retainer is narrow.

      2. A00307MC02
        *a Center Point of Fuel Pump Gauge Retainer

        Adjust the position of SST (claw) so that the hole in SST (plate) for installing SST (handle) is in the center of the fuel pump gauge retainer.

      3. Press SST (claw) against the rib of the fuel pump gauge retainer and tighten SST (bolt).

      4. A0030TFC01
        *a SST (Claw)
        *b SST (Plate)
        *c SST (Bolt)
        *d SST (Handle)
        *e Press down
        *f Pull

        Install SST (handle) to SST (plate).

        SST
        09808-14030   ( 09808-01010, 09808-01020, 09808-01030, 09808-01050 )
        09808-01071

        Note

        The torque required to remove the fuel pump gauge retainer may be as high as 200 N*m (2039 kgf*cm, 148 ft.*lbf) due to swelling of the fuel tank assembly, so perform the procedure with 2 people.

    3. While holding down on the center of SST (handle) to prevent SST from separating from the fuel pump gauge retainer, pull SST (handle) with another person pulling the opposite end of SST (handle), and slowly loosen the fuel pump gauge retainer by approximately 90°.

      Note


      • Be careful not to apply excessive downward force to SST, as this may damage the fuel suction tube with pump and gauge assembly or fuel tank assembly.

      • Turning SST at an angle may cause it to slip off of the fuel pump gauge retainer, so be sure SST is horizontal when turning.

      • To prevent damage to parts, do not turn SST too vigorously.

      • If SST slips off of the fuel pump gauge retainer, loosen SST (bolt) and install SST again.

    4. Continue to slowly loosen the fuel pump gauge retainer while another person is pressing down on the fuel suction tube with pump and gauge assembly to keep the protrusion of the fuel suction tube with pump and gauge assembly engaged with the groove of the fuel tank assembly so that the fuel suction tube with pump and gauge assembly does not move out of position.

      A002ZXOC01
      *a SST (Claw) *b SST (Plate)
      *c SST (Bolt) *d SST (Handle)
      *e One Person in Charge of Loosening *f One Person in Charge of Pressing Down
      *g Paint Mark - -

      Note


      • The fuel suction tube with pump and gauge assembly is pressed against the underside of the fuel tank assembly by a spring, and the constant upward pressure applied by this spring causes the fuel suction tube with pump and gauge assembly to rise up.

      • If the fuel pump gauge retainer is turned while the fuel suction tube with pump and gauge assembly and fuel tank assembly are not correctly aligned, the fuel suction tube with pump and gauge assembly will move with the fuel pump gauge retainer, and the fuel suction tube with pump and gauge assembly and fuel tank assembly may both be damaged.

      • Do not turn the fuel pump gauge retainer if the paint marks become misaligned.

  8. REMOVE FUEL SUCTION TUBE WITH PUMP AND GAUGE ASSEMBLY


    1. Remove the fuel suction tube with pump and gauge assembly from the fuel tank assembly.

      Note

      Be careful not to bend the arm of the fuel sender gauge assembly.

    2. A002ZN4C01
      *1 Fuel Suction Tube Set Gasket

      Remove the fuel suction tube set gasket from the fuel tank assembly.

    3. A0030CAC01
      *a Copy of Fully Tightened Mark
      *b Copy of Start of Threads Mark
      *c Fully Tightened Mark on Fuel Tank Assembly
      *d Start of Threads Mark on Fuel Tank Assembly
      *e Front

      Copy the fully tightened mark and start of threads mark of the fuel tank assembly.


      1. Copy the start of threads mark and fully tightened mark from the fuel tank assembly to the vehicle body in order to record their locations.

  9. REMOVE FUEL SENDER GAUGE ASSEMBLY

    Click here