Click here

ПЕРЕДНИЙ САЛЬНИК КОЛЕНЧАТОГО ВАЛА (для моделей без контроллера свечей накаливания) УСТАНОВКА

Click here
Click here Click here

PROCEDURE


  1. Click here

    INSTALL TIMING CHAIN COVER OIL SEAL


    1. Apply MP grease to a new timing chain cover oil seal lip.

      Note:

      Keep the lip free from foreign matter.

    2. A01LV45N01

      Using SST and a hammer, tap in the new timing chain cover oil seal until its surface is flush with the timing chain cover sub-assembly.

      09223-22010
      Oil Seal Tap in Depth
      -0.6 to 0 mm (-0.0236 to 0 in.)
      Note:

      • Do not tap in the timing chain cover oil seal at an angle.

      • Wipe off excess grease from the crankshaft.

  2. Click here

    INSTALL CRANKSHAFT DAMPER SUB-ASSEMBLY


    1. Align the key with the key groove of the crankshaft damper sub-assembly, and install the crankshaft damper sub-assembly to the crankshaft.

    2. A01LZQSC02
      *a Hold
      *b Turn

      Using SST, hold the crankshaft damper sub-assembly.

      09213-58014
      09330-00021

    3. Tighten the bolt to the specified torque.

      210 N*m 2141 kgf*cm 155 ft.*lbf
  3. Click here

    INSTALL ENGINE MOUNTING INSULATOR SUB-ASSEMBLY RH


    1. Set the engine mounting insulator RH sub-assembly onto the vehicle and engine mouthing bracket RH.

    2. A01LYYGN01

      Install the engine mounting insulator sub-assembly RH with the 3 bolts and 3 nuts.

      Bolt
      95 N*m 969 kgf*cm 70 ft.*lbf
      Nut (A)
      95 N*m 969 kgf*cm 70 ft.*lbf
      Nut (B)
      52 N*m 530 kgf*cm 38 ft.*lbf

    3. Connect the cooler pipe clamp to the engine mounting insulator sub-assembly RH.

    4. Install the cooler pipe clamp bracket with the bolt.

      9.8 N*m 100 kgf*cm 87 in.*lbf
  4. Click here

    INSTALL RADIATOR RESERVE TANK ASSEMBLY


    1. Install the radiator reserve tank assembly with the 2 bolts.

      5.0 N*m 51 kgf*cm 44 in.*lbf
  5. Click here

    INSTALL FRONT EXHAUST PIPE ASSEMBLY


    1. A01M2J6

      Using a vernier caliper, measure the free length of the compression springs.

      Minimum 41.5 mm (1.63 in.)

      If the free length is less than the minimum, replace the compression spring.

    2. A01M2OAC48
      *1 No. 2 Exhaust Manifold Converter Sub-assembly
      *2 Gasket
      *a Wooden Block

      Using a plastic hammer and wooden block, tap in a new gasket until its surface is flush with the No. 2 exhaust manifold converter sub-assembly.

      Note:

      • Be careful with the installation direction of the gasket.

      • Do not reuse the gasket.

      • Do not damage the gasket.

      • Do not push in the gaskets by using the front exhaust pipe sub-assembly when connecting it.

    3. A01M0TNC01
      *1 No. 2 Exhaust Manifold Converter Sub-assembly
      *2 Front Exhaust Pipe Assembly
      *3 Gasket
      *a Space Between Flanges: 8.5 mm (0.335 in.)

      Install the front exhaust pipe assembly to the No. 2 exhaust manifold converter sub-assembly with the 2 bolts and 2 compression springs.

      43 N*m 438 kgf*cm 32 ft.*lbf
      Tip:

      After installation, check that the space between the flanges of the No. 2 exhaust manifold converter sub-assembly and front exhaust pipe assembly are consistent front-to-rear and left-to-right.

  6. Click here

    INSTALL FRONT ENGINE MOUNTING BRACKET LOWER REINFORCEMENT (w/ Reinforcement)

    Click here

  7. Click here

    INSTALL FRONT SUSPENSION MEMBER REINFORCEMENT RH

    Click here

  8. Click here

    INSTALL V-RIBBED BELT

    Click here

  9. Click here

    INSPECT FOR OIL LEAK

    Click here

  10. Click here

    INSTALL NO. 1 ENGINE COVER (w/ No. 1 Engine Cover)

    Click here

  11. Click here

    INSTALL REAR ENGINE UNDER COVER RH

    Click here

  12. Click here

    INSTALL NO. 1 ENGINE UNDER COVER (for Half Cover Type)

    Click here

  13. Click here

    INSTALL NO. 1 ENGINE UNDER COVER (for Full Cover Type)

    Click here

  14. Click here

    INSTALL FRONT WHEEL RH

    103 N*m 1050 kgf*cm 76 ft.*lbf