БЛОК ДВИГАТЕЛЯ СНЯТИЕ

CAUTION / NOTICE / HINT

PROCEDURE

1. REMOVE COMPRESSOR STAY

   
   

   1. 

      Remove the compressor stay from the cylinder block sub-assembly.

2. REMOVE GENERATOR ASSEMBLY

   
   

   1. 

      Remove the 3 bolts and generator assembly.

3. REMOVE VACUUM PUMP ASSEMBLY

   Click here

4. REMOVE IDLER PULLEY COVER PLATE

   Click here

5. REMOVE NO. 1 IDLER PULLEY SUB-ASSEMBLY

   Click here

6. REMOVE NO. 2 IDLER PULLEY SUB-ASSEMBLY

   Click here

7. REMOVE NO. 4 WATER BY-PASS PIPE

   Click here

8. REMOVE STUD BOLT

   Tech Tips

   Perform this procedure only when replacement of the stud bolt is necessary.

   
   

   1. 

      Using an 8 mm socket wrench, remove the stud bolt from the engine mounting bracket.

9. REMOVE ENGINE MOUNTING BRACKET

   Click here

10. REMOVE V-RIBBED BELT TENSIONER ASSEMBLY

    Click here

11. REMOVE DIESEL THROTTLE BODY ASSEMBLY

    Click here

12. DISCONNECT NO. 7 WATER BY-PASS HOSE

    Click here

13. DISCONNECT NO. 8 WATER BY-PASS HOSE

    Click here

14. REMOVE EGR VALVE BRACKET

    Click here

15. REMOVE NO. 2 EGR PIPE SUB-ASSEMBLY

    Click here

16. REMOVE ELECTRIC EGR CONTROL VALVE ASSEMBLY

    Click here

17. REMOVE ENGINE OIL LEVEL DIPSTICK GUIDE

    Click here

18. REMOVE FUEL INLET PIPE SUB-ASSEMBLY

    Click here

19. REMOVE INJECTION PIPE SUB-ASSEMBLY

    Click here

20. REMOVE NO. 4 FUEL HOSE

    Click here

21. REMOVE COMMON RAIL ASSEMBLY

    Click here

22. REMOVE INTAKE MANIFOLD INSULATOR

    Click here

23. REMOVE DIESEL TURBO PRESSURE SENSOR

    Click here

24. REMOVE NO. 1 GAS FILTER

    Click here

25. REMOVE GAS FILTER BRACKET

    Click here

26. REMOVE ENGINE COVER BRACKET

    Click here

27. REMOVE NO. 2 INTAKE MANIFOLD

    Click here

28. REMOVE INTAKE MANIFOLD

    Click here

29. REMOVE GLOW PLUG ASSEMBLY

    
    

    1. 

       Remove the 4 glow plug screw grommets.

    2. Remove the 4 nuts and No. 1 glow plug connector.

    3. Using a 10 mm deep socket wrench, remove the 4 glow plug assemblies.

30. REMOVE NO. 1 CYLINDER BLOCK INSULATOR

    Click here

31. REMOVE WATER BY-PASS HOSE

    Click here

32. REMOVE NO. 6 WATER BY-PASS HOSE

    Click here

33. REMOVE NO. 8 WATER BY-PASS HOSE

    Click here

34. REMOVE NO. 2 WATER BY-PASS PIPE

    Click here

35. REMOVE NO. 4 WATER BY-PASS HOSE

    Click here

36. REMOVE FUEL TUBE SUB-ASSEMBLY

    Click here

37. REMOVE EXHAUST FUEL ADDITION INJECTOR ASSEMBLY

    Click here

38. REMOVE FUEL INJECTOR SEAL

    Click here

39. REMOVE NO. 3 FUEL HOSE

    Click here

40. REMOVE SUPPLY PUMP ASSEMBLY

    
    

    1. 

       Remove the 2 bolts, supply pump assembly and No. 1 supply pump drive coupling.

    2. Remove the O-ring from the supply pump assembly.

41. REMOVE FUEL HOSE PROTECTOR

    
    

    1. 

       Remove the bolt and fuel hose protector.

42. REMOVE NO. 3 WATER BY-PASS PIPE

    Click here

43. REMOVE NO. 1 TURBO OIL PIPE

    Click here

44. REMOVE NO. 1 VACUUM SWITCHING VALVE ASSEMBLY

    Click here

45. REMOVE VACUUM TRANSMITTING HOSE ASSEMBLY

    Click here

46. REMOVE NO. 1 WIRE HARNESS CLAMP BRACKET

    Click here

47. REMOVE NO. 4 MANIFOLD CONVERTER INSULATOR

    Click here

48. REMOVE MANIFOLD CONVERTER INSULATOR SUB-ASSEMBLY

    Click here

49. REMOVE MANIFOLD STAY

    Click here

50. REMOVE NO. 2 MANIFOLD STAY

    Click here

51. REMOVE NO. 2 EXHAUST MANIFOLD STAY

    Click here

52. REMOVE EXHAUST MANIFOLD CONVERTER SUB-ASSEMBLY

    Click here

53. REMOVE NO. 2 WATER BY-PASS HOSE

    Click here

54. REMOVE EGR PIPE WITH COOLER SUB-ASSEMBLY

    Click here

55. REMOVE TURBOCHARGER SUB-ASSEMBLY

    Click here

56. REMOVE DRIVE SHAFT BEARING BRACKET

    
    

    1. 

       Remove the 3 bolts and drive shaft bearing bracket.